How to remove govenor on Coleman ct200u ex, makes it go way faster for free
Пікірлер: 150
@Everlastandgreen3 жыл бұрын
DUDE this is what youtube needs more of. You went straight to the deal and explained it perfect without any problems. No 10 minute video ! Thank you
@evans_7.33 жыл бұрын
Heck ya dawg, that’s how it needs to be. Your welcome!
@candyapphole96354 жыл бұрын
I tried it earlier and it made my bike go a good bit faster. Went from 20 mph to damn near 30. Not a very big boost but a good one to me.
@notsewstudios62334 жыл бұрын
Same
@shootinnscootin55453 жыл бұрын
Now add a stage 1 kit and you'll be hauling ass like Jennifer Lopez's underwear!
@edwardrosales19862 жыл бұрын
Where can i order the stage 1 kit?
@candyapphole96352 жыл бұрын
@@edwardrosales1986 I bought mine on Amazon. It’s been a long time but I just looked up the bikes full name and stage 1 kit after.
@edwardrosales19862 жыл бұрын
@@candyapphole9635 is it still running good? I just got mine a few months ago
@Deepfried4skin4 жыл бұрын
That’s not the governer. That’s just a throttle limitation screw that limits how far your throttle can go. To remove the governer, you need to open up the engines and take out a little plastic gear along with the governer arm.
@brandondominguez14354 жыл бұрын
Thank you
@shootinnscootin55453 жыл бұрын
I don't recommend that.
@gamingwithalex85443 жыл бұрын
@@shootinnscootin5545 why not
@shootinnscootin55453 жыл бұрын
@@gamingwithalex8544 These engines are only made to withstand a certain amount of RPM's. By removing the governor screw you won't make the bike go fast enough to damage the engine but by removing the actual governor from the engine you risk ruining the valves. Unless you plan on upgrading your entire engine (valve springs etc) I wouldn't recommend removing the governor from the engine. Add a new exhaust, carb with a 0.38 jet and a high performance air filter and a torque converter and you should be good. These stock 196cc engines aren't meant to run at super high RPM's like the Predator or Tillotson engines.
@Deucealive752 жыл бұрын
@@shootinnscootin5545 I don't think that's a true statement. A stock Predator is no more capable to run at high RPM than a stock 196. Both engines will turn about the same RPM at valve float. And the quality of the Predator is no better than most 196 clones. When the governor is removed it is best to get a billet rod and flywheel for safer higher than stock RPM operation.
@OcotilloTom2 жыл бұрын
That's not the governor, that's the throttle stop or limiter screw. On later models it is spot welded in so you can't unscrew it. But you can bend down the metal tab that the end of the screw used to engage with the same results.
@pyrce1590 Жыл бұрын
How fast does it go now?
@TheGameBest73 жыл бұрын
That screw is the speed stop, the governor is associated with the long arm under the engines gas tank.
@skillchamp42082 жыл бұрын
I did this on my mini bike it went 25 but it idles If I quickly get up to speed is that normal?
@victorsanders34394 жыл бұрын
My man, that is not the governor, that is the throttle screw. The governor is inside the motor and typically the throttle screw is welded on by the factory and you just grind it off or bend the tab.
@alleditschris3 жыл бұрын
how do you bend the tab though
@victorsanders34393 жыл бұрын
@@alleditschris frocefully
@onesgone3972 жыл бұрын
With Thor’s hammer
@UltmtDrivng4 жыл бұрын
this helps a ton! LMAO my dad is telling me I cant because it goes to fast but this vid made it possible thanks so much man I will definitely sub
@evans_7.34 жыл бұрын
Thank you nobody here knows the bike and just making hate comments but thank you
@williamhiggins8354 жыл бұрын
Evan Rice you’re the one that doesn’t know the motor you dipshit. Lmfao
@crackerjack96084 жыл бұрын
lmao my man the governor is inside the motor i wish it was this easy tho
@evans_7.34 жыл бұрын
Actually if you knew this bike it’s just the screw, do your research buddy 😂
@crackerjack96084 жыл бұрын
@@evans_7.3 what youre talking about controls the throttle fuck nuts looks it up
@williamhiggins8354 жыл бұрын
Evan Rice you’re obviously the one that needs to research. All you did is remove the throttle adjustment screw, and you don’t have to take the air filter off to do it.
@chucknas24204 жыл бұрын
Evan Rice 🍚
@chucknas24204 жыл бұрын
Evan Rice 🍚
@shootinnscootin55453 жыл бұрын
This won't cause any internal damage?
@Everlastandgreen3 жыл бұрын
Just remove the screw only. Some people cut the end off, some drill the screw away. I'd recommend watching more youtube videos about this. The screw is only there to make it safer for driver so they dont go too fast. Removing it makes you go faster and that's all
@LFUKO3 жыл бұрын
Do you know the top speed without the governor?
@SorryChica3 жыл бұрын
18-20 mph
@SaintJames402 жыл бұрын
Can you make a video showing how fast?
@gamertj17974 жыл бұрын
What socket size I need to get to the switches
@evans_7.34 жыл бұрын
Gamer tj I don’t remember sorry
@julies1ify2 жыл бұрын
QUESTION: I cut mine off as they tack weld them now. Since I did that, it surges at full throttle almost like its not getting enough gas. Anyone have the same issues or know how to remedy ? Thank you
@tristenmccabe Жыл бұрын
The surging that you're feeling is the governor kicking in now that you've removed the throttle screw to get rid of that you'd have to remove the governor and that would involve opening the cover of the motor removing the plastic governor and the arm it's not that difficult and there are videos on KZbin for how to do it but once you do it the motor will spin it much higher RPM and I can get a little bit dangerous
@julies1ify Жыл бұрын
@@tristenmccabe, Thanks for the answer ! I actually adjusted the throttle play so I cant go full throttle and no more surging. Its fast enough for me tooling around my property & farm fields around me. At almost 59 & still a knucklehead, figure the slower the better lol. Thanks again for the advice !
@somewhere-n-Texas2 ай бұрын
@julies1ify how do you adjust the throttle play? Mine was doing the same thing yours was doing, "surging"...
@thomaschicka54923 жыл бұрын
So this will cause no wear and tear on the engine and no problems??
@evans_7.33 жыл бұрын
None at all
@xNELVKALEN2 жыл бұрын
Anyone aware of these screws being soldered/welded preventing them from being tampered with? Right now looking like a grinder job. Perhaps that’s where the cutting idea came from.
@xNELVKALEN2 жыл бұрын
You can simply bend the tab that contacts the screw instead of cutting or grinding it off if you also run into this problem.
@johncarlos31203 жыл бұрын
My screw is welded on there any advice 🤔
@julies1ify2 жыл бұрын
I used a Dremel to cut it off
@edwardrosales19862 жыл бұрын
So if i take off the throttle screw, how fast can the bike go?
@mr.bubbles16212 жыл бұрын
Mine went from around 21 to darn close to 35
@Slicknewt3 жыл бұрын
That screw comes welded now so you have to cut it or bend it
@rdw06933 жыл бұрын
That sucks
@Imnotreal232 жыл бұрын
Could you drill through it? I'm looking to buy a coleman but I found the screw is welded like you said. So if I need to cut the screw off im not gonna get one, instead I'll build one
@julies1ify2 жыл бұрын
I used a Dremel
@spicystuber3 жыл бұрын
what do i do if the screws stripped
@evans_7.33 жыл бұрын
Idk
@spicystuber3 жыл бұрын
@@evans_7.3 i just took off it and im in pst so i gotta wait until tommorrow to see how fast it goes without the bolt
@FKEYYT3 жыл бұрын
My screw melted it’s like welded melted so I can’t unscrew it any suggestions
@evans_7.33 жыл бұрын
Maybe use a cut off wheel or something the years after mine have then welded screw
@firemansam9513 жыл бұрын
Little question, will this cause engine problems?
@evans_7.33 жыл бұрын
Well it’s been 7 months I’ve had the same motor and it runs fine, send it my man 🤘🏼
@firemansam9513 жыл бұрын
Evan Rice yeah, im gonna be getting a trail master mb200 this christmas its gonna be sick!🤘
@GMC.Sonoma.4.33 жыл бұрын
I’m trying to get a tractor supply mini bike. Coleman ct200uex same model as this one but in jet black.
@Sam_k7213 жыл бұрын
@@GMC.Sonoma.4.3 I just got that one a month ago fantastic bike looks so slick
@user-zm7dd5ib7l4 жыл бұрын
I fought the governor was inside the motor
@evans_7.34 жыл бұрын
jacob Thompson if you didn’t know about these bikes I’m pretty sure the screw is the governor on these bikes and you can only undo the screw on 2017 and under models 2018 and up they’re welded
@509ryan4 жыл бұрын
@@evans_7.3 thats not a govenor
@williamhiggins8354 жыл бұрын
It is inside the motor, this kid just took out the throttle adjustment screw. Lmao
@westonporter97353 жыл бұрын
Evan Rice that’s not a governer bruh were you raised in the woods
@killdoize58293 жыл бұрын
@@evans_7.3 nah bro that’s the throttle screw the governor is under the engine
@jeffreyferris35594 жыл бұрын
Doesn’t work on new 200uex bought one brand new in June of 2020 at tractor supply they put a small spot weld on the head of the throttle screw making it impossible to adjust or remove with a screwdriver have to cut screw off
@evans_7.34 жыл бұрын
Jeffrey Ferris I’m pretty sure it’s either 2019 or 2018 models and older have the screw, the new ones have the spot weld
@jegammer13243 жыл бұрын
U could just bend back the meatle tab that the screw hits that's what I did and it works
@altraveling70192 жыл бұрын
@@jegammer1324 How is your Coleman running now? I bought one yesterday 2021 and it is welded but I’d like to try your method
@michaelmiller98704 жыл бұрын
The governor is inside motor.
@duggiebadd28044 жыл бұрын
My screw is welded on so I just bent that little bracket that’s in front of it back so it doesn’t hit
@jaytee35654 жыл бұрын
I ran into same issue.. dam welded screw 😩
@duggiebadd28044 жыл бұрын
@@jaytee3565 Does your spring extend more now? Picks up close to 10 mph more
@jaytee35654 жыл бұрын
@@duggiebadd2804 yes I also added a ziptie to the spring connected to the governor arm. That really helped out with top end. Does about 35mph now.
@ConstantStone124 жыл бұрын
Mine was also welded but you can easily cut it off for the same result
@goose2363 жыл бұрын
What bracket
@LFUKO3 жыл бұрын
There was a weld on it so me and my dad just grinded it off
@jvince66523 жыл бұрын
On newer models that screw is welded in. But it isn't the govenor.
@georgekershner66263 жыл бұрын
Ok its not the GOVERNOR BUT FOR THE PURPOSE OF GOING FASTER AND NOT BLOWING UP THE MOTOR YOU CAN BEND DOWN NEW ONE OR UNSCREW OLD ONE, I LOOSEN UP CABLE TO LET SPRING COME BACK A BIT, I THINK YOU WANT YOUR SPRING THERE TO PUT YOUR THROTTLE BACK IN PLACE SO YOU CAN GIVE IT GAS AGAIN IF YOU MOVE THAT SPRING ALL THE WAY BACK OR TAKE IT OFF YOU'RE GOING TO HAVE ONE LOOSE ADJUSTMENT THAT'S GOING TO GO ONE WAY AND STAY WIDE OPEN. THE GOVERNOR IS INSIDE THE MOTOR TO KEEP THE MOTOR FROM BLOWING UP IS NOTHING THAT THESE PEOPLE NEED TO BE MESSING WITH MY NEW MOTOR IF YOU WANT TO DO THAT
@RealestateKingThe14 жыл бұрын
Bruh that is not the governor the governor is inside the motor that is the screw that keeps the throttle from not going to fast
@sheepdogpleb15093 жыл бұрын
Thank you for the video 👌🇺🇸
@markt51294 жыл бұрын
throttle screw is not govermor
@tracyazevedo2 жыл бұрын
How exactly did you remove the screw I’ve tried with a screwdriver and drill but it keeps trying to strip it
@billyschannel9972 жыл бұрын
Your screw is probably too tight
@gamingjoni51112 жыл бұрын
they are welded on
@julies1ify2 жыл бұрын
Mine was tack welded, I cut it off with a Dremel. Much faster but surges @ top end ?
@landonjones78213 жыл бұрын
Thanks my dad put the throttle screw back in because he didn’t trust me lmao
@theglizzymaster26923 жыл бұрын
Mine is welding
@dylanwatts86094 жыл бұрын
Thats the throttle screw not the governor
@trokiandocuh53504 жыл бұрын
You call 25mph scary
@evans_7.34 жыл бұрын
tilyer Ochoa it was u til I got used to it, first mini bike man
@UltmtDrivng4 жыл бұрын
@@evans_7.3 yes sir that's true also don't listen to that guy there are a lot of toxic people on YT
@UltmtDrivng4 жыл бұрын
@@evans_7.3 Also im curios does this actually make a difference because people are saying its not the governer
@JAIW34 жыл бұрын
Swift Killz yeah is this safe? , I did this to my warrior 200 .. lol I’m not tryna blow off a leg
@trokiandocuh53504 жыл бұрын
@@UltmtDrivng it's not a governor it is just the throttle screw
@Jolene_4003 жыл бұрын
On mine they welded the nut in
@automotiveaudit11353 жыл бұрын
That’s not a governor bud
@lantz864 жыл бұрын
That's not the governor.
@evans_7.34 жыл бұрын
lantz86 then what is it? I’m curious to know.
@lantz864 жыл бұрын
@@evans_7.3 all that is, is a throttle limiter. It just causes the throttle to not be opened up all the way. You can adjust as need be, or remove it like you did. The governor is a small gear inside the crank case that causes pressure on the crank shaft when it is running. You have to open the crank case to remove it. You can do it I'm sure!
@JAIW34 жыл бұрын
lantz86 yo is doing this bad ?
@lantz864 жыл бұрын
@@JAIW3 depends on which you're talking about. Removing the throttle limiting screw is not bad at all. However, puting a zip tie or something to restrict the governor is. It needs to be completely removed or you could easily destroy the engine.
@Dezmon2jz4 жыл бұрын
Yeaa no this isn’t the governor, it still boggs out
@evans_7.34 жыл бұрын
Dezmon Ballard wym did you try it
@effyoo60814 жыл бұрын
I took out the governor. Watch redbeard garage if you haven't already. Put that screw back in. The governor is what makes the engine surge back down to the set rpm. 3600 I think. It literally pulls the throttle back down via an internal gear. If u want a burst of speed, pull back (to the rear)the other bar, the long bent one under the gas tank. It bypasses the gov. and gives u an idea what its like. You MUST take the side of the motor out and remove all parts. While your in there take out the oil float that kills the engine when u hit a bump too.
@brandondominguez14354 жыл бұрын
Mine is Weld
@garrett.w80244 жыл бұрын
Yeah mine was too if you go to where the screw is and take a hammer and maybe a Flathead screw driver and can kinda jam that little metal tab down then the screw will go right past the barrier basically doing the same thing in a harder fashion.
@alexree22734 жыл бұрын
Same
@MotivationDaily1723 жыл бұрын
@@garrett.w8024 I don't wanna brake my bike 😂😂
@garrett.w80243 жыл бұрын
KSMA Clan yeah I know how it is, I was pretty scetched our when I tried it but it turned out fine after about an hour of tinkering. But it’s all worth it now cause when me and my cousin race I always win😂