How to remove your 2013-2015 Lexus ES300H rear bumper | ReveMoto

Learn how to quickly remove your 2015 Lexus ES300 or ES350 rear bumper cover. You only need a wrench and a flat-head screwdriver!
Where to purchase: bit.ly/13-15_LXES300
Visit us: www.revemoto.com
0:00 Start
0:13 Intro
0:52 Bumper bolt location
2:20 Remove the lower bumper bolts
2:52 Remove 2 push-pins
4:10 Bolt locations on each side
4:40 Remove center bolts & push pins
6:12 Remove the top bolts
7:22 Rear bumper removal
8:24 Unplug the sensor harness
9:04 Recap
9:31 Outro
Thank you for watching our Lexus ES300 rear bumper cover removal. We aim to provide a detailed tutorial on our parts removals and installs. These jobs are a lot easier contrary to what most people think. Hopefully, you can save some money and time by doing this DIY job yourself. We removed this bumper to repaint it. As you can see, there were some gashes on the side.
TOOLS NEEDED:
You will only need a 10mm socket wrench or plain wrench. Feel free to use and impact gun to make things faster. You will also need a panel clip removal tool. If you are like us and love to torutre yourself, you can use a flat-head scewdriver.
PROCESS:
This is very simple bumper removal. We love working on, what is essential a Toyota. Toyota really thinks about the simplicity in their structural design. Once you get passed the fear of working on a car, it's super easy
First, we started by removing the top bolt on the ends of the bumper. We demonstrated this on one side of the bumper but the process is the same for the opposite end. There is one 10mm bolt connected to each bumper bracket that needs to be removed. After that we moved on to the lower bumper. We started with side we were on, but there is a total of 4 bolts and 4 push-pin clips on each side. Use your panel clip removal tool to take off the clips, it's pretty easy. There are 4 bolts in the middle of the bumper and 2 clips total. Now you can move to the final two bolts which are located behind the trunk. Lift that trunk up and locate the two small squres or bolt covers. Pop those off and use your 10mm socket wrench to remove the last bolts.
Now we can dismount the bumper by pulling each end out and working towards the middle. If you ES300 has sensors, be sure not to let the bumper fall and disconnect the wire harness. Just press down on the clip and separate the connectors. You are closre to being a pro now. The install process is the same just work in reverse. Good luck and thanks for watching!
Follow Us on:
FB: / revemoto
IG: / revemoto
Twitter: revemoto?lang=en
_________________________________________________
#ES300H #paintedautoparts #revemoto #lexuses300 #lexus #highquality
#ES300 #paintedautobodyparts #paintedcarparts #sideviewmirror #diy #replacementmirror #howto
DISCLAIMER: While ReveMoto tries to make the information in this video as accurate as possible, we make no claims, promises, or guarantees about the accuracy, completeness, or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself (DIY) projects entail some risk. It is the sole responsibility of the viewer to assume this risk. ReveMoto is not responsible or liable for any loss, damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@ReveMoto]

Thank you for watching! Please follow the link below for the rear bumper or any other part you may need! Where to purchase: bit.ly/13-15_LXES300

[@tonyhull5539]

Good video, it gave me great info on how to remove my bumper. BTW, the small cover inside the trunk, the description for the strap is a 'Retaning strap'.

[@ReveMoto]

That you so much! I couldn’t figure out what that thing was called. Appreciate it. Go to www.Revemoto.com

[@richardbell8329]

Nice Job!

[@ReveMoto]

I really appreciate it! Let me know if you had any questions

[@bonearchetype]

Thanks for the instruction. It wouldv'e taken me much longer to find those hidden bolts behind the rear wheel

[@ReveMoto]

You are very welcome! If you ever need replacement parts hit ⬆️ www.Revemoto.com

[@augustineacunia3215]

2014 GS350 FSport pretty much the same procedure? I didnt know the center four were 10mm bolts I thought it was just plugs. Mines ripped out when I snagged a curb. Nice vid.

[@ReveMoto]

Hello! It should be the same process. I think the only difference is the lower valance on the GS, and that should have a bunch of clips holding it on. Thank you for watching!

[@AugDaug]

@@ReveMoto yes the lower valance has clips. Ordered those. Now I just have to replace the valance with my new one. Thanks again.

[@sayedmurtazahussaini5434]

Thanks

[@ReveMoto]

No problem! Please subscribe, it helps our channel grow 😃

[@robertallums6636]

I have a small gap by the taillights what did I miss and what should I do?

[@pericaperko1031]

Hi do you have a video of 2010-2015 rx350? And do you know if its pretty much the same process for removing the back bumper? Thank you

[@ReveMoto]

Yes these Lexus have a very similar removal process. When you remove thee side and under bolts/push pins. Then it’s still stuck try removing the taillights that might have a bolt also holding bumper

[@ReveMoto]

If you need this bumper give us a shot at www.ReveMoto.com

[@suezulauf1605]

Want to replace bumper , can I take sensors off & put on new one ???

[@ReveMoto]

Hello and yes you can. The sensors are not hard to remove once the bumper is off. A majority of the time, the senor just plugs in with no calibration needed. They are often clipped on to the bumper which makes it easier. Sensors are expensive, so make sure you only buy the ones you need. Thanks for watching!

[@jado4you]

Parking assist malfunction lights on. How can I check the sensor which one is bad?

[@ReveMoto]

Sorry that I am not to sure. First I could look at which sensor has any damage, then go to dealership if none has visible damage to see if they can locate

[@emmanuelperez4379]

would it be the same for a 3rd gen gs350?

[@ReveMoto]

Removal and install yeah very similar. Please go to www.ReveMoto.com if you need parts

[@bigstranger5789]

Hi I have a 2015 es 350 lexus, what is that wire/ plug called that you disconnected with the sensor?

[@ReveMoto]

Hello! We're unsure on the proper name. The harness is for the parking sensors for the rear bumper, so if you were to tell Lexus, they should know you are referring to the rear bumper sensor harness. Where that plugs into, that should be the main wiring harness. Thanks for watching!

[@bigstranger5789]

Ok, so the harness stays with the bumper? I bought my car crashed and it was missing the back bumper, so that part stayed with it. It has 2 wires? Thank you. I found some that were close, but not the same.

[@user-hj4mf7uw7s]

thx~

[@ReveMoto]

You are very welcome! Go to www.ReveMoto.com for more car parts

[@jrdabossleelee3289]

Is it the same as the es 350

[@ReveMoto]

Hello and yes, it should. I believe the es350 just has a different style lower valance but it should be near identical. Thank you for watching!

[@sayedmurtazahussaini5434]

Please make all model s

[@ReveMoto]

Hi Sayed! Are you requesting for sports model if this vehicle? Like the F sport?

[@sayedmurtazahussaini5434]

@@ReveMoto I mean all luxes models Subaru and etc

[@ReveMoto]

If we can we will! Please subscribe 😃

[@MrDewnay]

Hi does the bumper have to be removed in order to change out the bottom reflectors on the bumper?

[@ReveMoto]

Hello. I suppose, if you loosen the bumper enough to reach behind the bumper to loosen the reflectors, no. Good luck!