How to repair concrete ceiling tarnish.

[@handymanag]

Nicely done video. Will definitely use it as a guide.

[@bucky167]

How much would it cost to do one room the whole ceiling

[@lekshmijs4035]

Suggest tha name of an additive used for better grip??

[@amiralikhan061]

Hi thank you. I need to repair the roof but it's wet due to damp what material you recommend me to use.

[@michelghafari8684]

Great video , I did exactly how you told it but the only thing I couldn't get right is the flashing through the paint, I used stain blocking paint than ceiling paint and it still flashes .do you know which paint to use to help with that Please ?

[@jdhrhandymanservices3449]

Thanks for watching the video. It is a bit difficult to know what is happening without seeing at least a photo. So it could be several factors: 1- Do you correct the leak of the roof before doing the work? There are occasions when after correcting the leak you have to leave an adequate time for the concrete to dry and remove the moisture caused by the leak. Such moisture causes stains in the repaired area. 2- If you do not pass a wet sponge to soften the tarnish for the finish this will look very rough and when painting it will be very noticeable. 3- If the paint used did not cover the stain try an industrial type paint (designed for ceilings), Thank you I hope these recommendations help you.

[@rameshchandrashah7107]

Are you serving at Ahmedabad?

[@gmp_gmp]

In commercial building as the occupants change new occupants come as per their requirement they make small holes for wiring & interior works in beams , Columns & ceiling , will it effect the structure in long run say 20-25 years due to moisture entering RCC through these holes ?

[@jdhrhandymanservices3449]

Thanks for your comment. Each situation is different and the climate is different in each place, for which you should consult a specialist in the area where the structure is located. It is advisable to cover the rest of the hole through which the cables pass with silicone to protect the rod from the inside, but if the area where it is very wet this will not stop the deterioration of the rod.

[@chandrashekharbarge4160]

Good information

[@indulkarshailu]

Systematic video. Informative comments section interaction . Looking forward for few more videos,yes subscribed.

[@alisid4947]

I have very similar ceiling corosion in my basememt with bars rusted due to water leakage. I am havig it repaired

[@jdhrhandymanservices3449]

Thank you for your comments and for watching the video.

[@sekirobaba7171]

For how much time Water was leaking???

[@jellyg.8961]

Thanks a lot for the video, I need to repair a hole I have in the roof on my house and this is how I need to do it. My doubts are now with consistency of the concrete mix and that's what I would like to ask. 1. Does the concrete mix has to be very dry with lots of clumps on it or it has to be more watery with little clumps like a cake mix in order for it to adhere and not fall? 2. How much time should I wait after putting a first layer to dry and put the other layers? The hole on my ceiling has some spots that are about half to 3/4 inch deep so I need to fill those firsts. Thanks a lot for all the help!

[@jdhrhandymanservices3449]

Hi, thanks for watching the video. The consistency of the cement is similar to peanut butter, neither too wet nor too dry. You should plug the deepest gaps first and continue to fill evenly until you reach the point of about 1/8 of an inch from the existing ceiling. The cement that I used first (Rapid Set) contains in its composition a drying accelerator and it dries between 10 to 15 minutes, so do not prepare a lot of mixture to give yourself time to put it on. the other cement takes about thirty minutes to an hour to dry depending on the temperature in the area where it is being worked.

[@jellyg.8961]

@@jdhrhandymanservices3449 hey, thanks a lot for your answer and explanation. I was going to use Quikrete green bag mix which has fiber but now I will go with the rapid setting one.

[@danielgichangi1339]

At where place you are , I can do

[@michelghafari8684]

thanks for a great video, my question is the paint that goes over the cement do you have a preference and can i put a coat of mud on top to give a better blend Ty

[@jdhrhandymanservices3449]

Thank you for watching the video and I'm sorry for the delay in responding. Ceiling flat paint.

[@bhushanpolavarapu2086]

give details of 2 chemicals to buy on line

[@jdhrhandymanservices3449]

Hi and thanks for your comment. For the Bonding Agent i used, Tex-Gold Bonding Agent. www.homedepot.com/p/Bull-Bond-1-Gal-Tex-Gold-Bonding-Agent-BA4PTG/202820366#overlay For the first layer and fill until near the ceiling level i used, Rapid Set Cement All Multi-Purpose Construction Material. www.homedepot.com/p/Rapid-Set-55-lbs-Cement-All-Multi-Purpose-Construction-Material-02010055/202188447 For Tarnish i used, Quikrete ready to use Concrete Mix. www.homedepot.com/p/Quikrete-60-lb-Concrete-Mix-110160/100318478

[@atkins8644]

How do you bond old concrete and new concrete (layer).

[@mandywu779]

What red oxide did you use?

[@jdhrhandymanservices3449]

Hello and thanks for watching the video. you can use any brand. In my case I like to use Rust Oleum Red Oxide Metal Primer.

[@TKO67]

zero bond? What brand did you use?

[@jdhrhandymanservices3449]

Hi thanks for your question. The brand i use is Bull-Bond. The product is Tex-Gold bonding agent. here is the Link. www.homedepot.com/p/Bull-Bond-1-Gal-Tex-Gold-Bonding-Agent-BA4PTG/202820366

[@GalactusDaDevourer]

Saludos! Soy de Puerto Rico, del área metro. Tengo esta situación en mi casa. Como me puedo contactar con usted?

[@jdhrhandymanservices3449]

Hola gracias por ver el video. Lamentablemente no estoy prestando servicios en Puerto Rico. Gracias.

[@raymondsworld106]

Yo tengo él mismo problema en mi casa y grabe estoy esperando a vivienda para ayudarnos y siguemos en la espera porque mi suegra tiene condiciones y la casa se empezó afectar desde Maria

[@Charlieant2887]

Lo mejor, es tratar de exponer la varilla lo mas posible para poder limpiarla, luego q este expuesta, limpiar la varilla bien para sacar la corrosion lo mas posible. Yo le daria una manito de inhibidor para neutralizar la corrosion y luego le puedes poner el oxido rojo. Y si consigues pintura epoxica de metal seria ideal, creo que home depot o national la puede vender al Igual que el oxido rojo. Luego es meterle cemento, existen slgunos que tienen inhibidores tambien. Pregunta en Home Depot. En Puerto Rico sufrimos mucho en techos pues nuestros techos muchos son FLAT y al no desaguar el agua busca por donde entrar. Es importante ver por donde esta entrando el agua, porque sino te seguira pasando… Suerte y Exito

[@ravindradigambarlingade3859]

I have house of RCC 15 year old and my old slab was not in good condition that is leaking every rainy season and I build 2nd floor 2 year ago but my 1st floor kitchen slab is little bend what I do

[@jdhrhandymanservices3449]

Hello and thanks for watch the video. Although this is not related to this video, it may be for several things that the kitchen slab is curved, without observing it and verifying it in person it is a bit difficult to know why it bent, but according to you, it seems it was after building the second level, so it may be If the weight of the second level is too much, you must reinforce the ceiling of the kitchen with resistant beams. Consult a specialist in your area of residence. The video is as a reference of how I did the work, I am not responsible for any accident or problem that occurs to anyone who follows these recommendations. Always consult a professional and check the building regulations in your area of residence . Thank you.

[@lui26g50]

Im with the same problem preferably sa kitchen ground floor. I dont know any specialist to inspect the said area. It bend already when we build second floor,tiled also the second floor.😩.

[@shafiyullah3527]

Price per sqft with labour and material?

[@jdhrhandymanservices3449]

Hi and thanks for watching the video. Sorry but prices vary depending on the area.

[@loganathapandian8904]

After paint with red oxide all the important steps means name of the bond and chemicals We could not read as it did appeared quikly

[@loganathapandian8904]

Corrections dis appeared quickly so we cannot read and benefit

[@aswathrumba5431]

Tq very helpful..

[@jdhrhandymanservices3449]

Thanks for your comment!

[@gladysorsos6538]

thank you. i have same problem that i need to fix..

[@jdhrhandymanservices3449]

You are welcome

[@lissa2m]

Did you add any framework after to hold cement in place?

[@jdhrhandymanservices3449]

Hi, thanks for your comment. The cement is added in layers, allowing each layer to dry enough to continue adding the necessary layers until it reaches the ceiling.

[@ahmedm9557]

Is it save to do the same of this video for area about 1×1 meter ?

[@jdhrhandymanservices3449]

All work is completely different, you should check the building regulations and consult a professional in your area of residence. If the rods are very thin you should reinforce them, I have done this work in areas of 3 meters by 3 meters without any problem, it will take longer to do it. The video is as a reference of how I did the work, I am not responsible for any accident or problem that occurs to anyone who follows these recommendations. Always consult a professional in your area of residence. Thank you for your comments and for watching the video.

[@206flyer3]

Thanks for the video. Why do you use two types of cements ? Using two types adds strength ? Is it OK to use the Rapid Set to cover and finish the affected area ?

[@jdhrhandymanservices3449]

Thank you for watching the video and I'm sorry for the delay in responding. Use the Rapid set first to fill in and the quikrete for the last layer for finishing. The reason why using two different is: Rapid set for its ability to dry quickly helps you to do the job faster and the Quikrete is slower drying that helps you make a more professional finish. Thank you.

[@edwinarcenal5770]

you must replace the damage rebar

[@TKO67]

no you do not have to

[@jdhrhandymanservices3449]

In this case it was not necessary to replace the rod, there are cases that the rod has rotted so much that it has become very thin, in that case you can add new rod next to the thin rod and weld it to reinforce that area. But if all the rods that support the concrete are so rotten and have all become very thin, it would have to change the roof of that entire area. The video is as a reference of how I did the work, I am not responsible for any accident or problem that occurs to anyone who follows these recommendations. Always consult a professional and check the building regulations in your area of residence . Thank you.

[@Loonypapa]

@@TKO67 Yes, you do.

[@VRocksAshinAlphy]

👌

[@jdhrhandymanservices3449]

Thanks for your comment!

[@williamoseo3277]

Must be in actual footage

[@jdhrhandymanservices3449]

Hi, thanks for watching the video. The photos are of a work done by me and are real photos taken by me.

[@gduppyz2103]

Do not use a sledge hammer

[@WWEENETWORK]

Renovating a 1950s mid center modern beach house. kzbin.info/www/bejne/hmanoZ6LoJt4ppI Have this going on downstairs in my laundry room. Thinking of repairing it like this. But then putting Concrete Board...or the green sheet rock for the celing then tiling the entire walls which are mokd prone up to said ceiling. The laundry room is on the seaside and will double as a small catering kitchen and a wet space.