How to repeat or boost a weak public wifi service into a building

[@techydiy]

Visit the techydiy Amazon com shop and help support the channel: www.amazon.com/shop/techydiyorguk

[@techydiy]

Piyush Tripathi The TP-LINK WA5210G specification is for 2Km (1 1/4 Miles), but it depends on the environment, whether you have good line of sight, the equipment used at the other end etc.

[@duguder]

1:09 Can I use ethernet to usb adapter for my chromebook?

[@techydiy]

+Phong Nguyen Yes as long as you can chnange the ip address on the adapter it will work fine.

[@josephbarnett2613]

So does a computer need to be hooked to the system at all times or just for the setup?

[@techydiy]

Just for the setup

[@aleksandrcrypter648]

Спасибо 🙏 помог очень!

[@samimsekh]

Thanks for uploading the video...

[@techydiy]

Thanks for the comment!

[@yulivalverde3964]

Hello how are you. I liked your video but I have some questions I would like respondieras. 1. why it must be configured in client mode Ap router? 2. ¿porque not simply in client mode and connected to an access point? 3.- Being configured as you say, the tp-link WA5210G transmits only wifi or cable? I mean: I can connect via wifi to tp-link WA5210G without using the tp-link WA701ND? I really hope you clarify these doubts. Thank you very much for your input and video. A greeting.

[@techydiy]

I don't really understand your question but there are several reasons why you might want to use this setup: 1. The wifi signal you are trying to access is physically shielded and you are unable to access it from your location. For example, if you are inside a building and the wifi service is external to the building. The configuration described in the video can extend the signal into the building where it can be accessed by any wifi device. 2. The service you are trying to access only allows one device to connect to it and you want to connect several devices to that service. Several wifi services limit the number of devices associated with one login. 3. You are trying to access a distant weak wifi service with a device that has a poor antenna. Most tablets and phones have poor antennas. An external antenna with direct line of sight makes a huge difference. Hope that helps.

[@yulivalverde3964]

Thank you for answering, helped me a lot. Anything else; Does the outside antenna is connected when and retransmits the air wifi signal? or the acces point which emits the signal? A greeting!

[@techydiy]

+Yuli Valverde 5210g is located outside and connects to the WiFi service. The 701 is inside and connects to your devices (Phone, tablet, laptop etc.). The 5210g has two built in high gain antennas, it can also operate with a higher power output than normal.

[@javedsipra8730]

techydiy sir , I have some questions here , 1- can this device direct on mobiles phones , tablets , laptops ? How much capacity for users maximum on this device ? Or please suggest me Device who direct connect with mobiles for outdoor wifi business ? 360° coverage with maximum range 200 meters to as possible +point to point to multi point , and for maximum users capacity from 200 users to 5000 users as possible ? Plz come on whatsapp [phone] Javed Sipra is my name

[@chess2u]

Yuli terminaste la ultima palabra en espanol,nose si el abra entendido lo q le dijiste anteriormente

[@exkinky]

This seems really simple until I tried it with my MAC, nothing matches and got really frustrated so had to quit, i would thing things would match but they dont come close, do you have this for MACs?

[@tonytony01]

thanks was very informative. so only works with 2.4GHz extenders? what about other routers? I have an asus RT-AC3200. I am on NYC that has in some places free public wifi but the first time you need to sign on putting email address

[@techydiy]

The method should work with most types of access point / routers

[@TakKerna]

can i just connect the outdoor cpe to my pc to access the internet instead of running it through the indoor access point or does the indoor access point serve some purpose beyond just repeating the signal wirelessly?

[@techydiy]

Yes, you can do that.

[@jhepots]

is it possible to add or make a LAN connection through WA701ND? I'd like to add a 24 port switch hub on it. thanks

[@techydiy]

Yes.

[@jhepots]

+techydiy so, i can use any "4 port" wifi router instead of using WA701ND (let say TL-WR740N)? and one more option.. From WA5210G to TP-link(PoE, LAN), from LAN directly to 24 port switch hub. is it possible? sorry if i have a lot of questions sir. Thanks so much.

[@techydiy]

+Efren Junior You can add an ethernet switch or hub between the WA701ND and the WA5210G. You should then be able to connect another ethernet device into the hub with it configured for dhcp. e.g. A laptop connected with an ethernet cable You might be able to power the WA5210G directly from the switch over POE if the switch is compatible e.g. Same voltage etc. otherwise you would have to use the POE adapter. I don't know if the WR740N will work as a replacement for the WA701ND in this application. Thanks, Nigel

[@jhepots]

thanks nigel. i hope it all works for me.

[@techydiy]

If you try it please let me know how you get on. Thanks N.

[@abdorrahmanlachgar4655]

Hi is working on any router i have tp link wa7210n

[@rroberge418]

Hi i have a site (motel) with 7 small buildings (wood wall). the entire site have 290 meters long x 100 meters large. I want to give wifi internet access to my customers inside and outside the buildings. it will work with that type of device (cpe210)? i plan to install one as an ap router wired to my pppoe provider, and 3 other on the roof of a building on the center of the site (ap client router). thank you and sorry for english errors i speak french!

[@techydiy]

+Ronny Roberge Yes it should be able to cover that distance.

[@rroberge418]

+techydiy wow what a fast reply ! you think that at this distance of the outside antennas will be strong enough to have descent connections on mobile devices inside buildings? alors do you know the number of possible simultanous connections ?

[@techydiy]

+Ronny Roberge I can't say for certain as it depends on many factors. If you site them high with line of sight of the buildings then it sounds reasonable. My advice is buy one unit and try it.

[@stilessimon]

Hey, I'm watching this video for the third time now and I'm just trying to wrap my head around all this to hopefully include this setup in my camper (I'm doing a 2 yr long trip and this would really help). The internal router can run it's own network for my devices to connect to, and doesn't need to repeat the original network the WA5210G connects to correct? Secondly for mobile purposes, I would be changing the connection point often, how would I control which network the WA5210G connects to, can I authenticate with networks that need a login (accept terms of use) like starbucks or mcdonalds, and better yet is there a way of automating that process?

[@techydiy]

Simon Stiles The configuration is basically designed to do what you are asking. To select an external network then you need to access the configuration menu on the WA5210G, select Wireless, wireless mode, then select the survey button to see what services (SSIDs) are available. You can then connect to the service that you require. Access to services like McDonalds Wifi works fine, you connect to the service (SSID) as above and then use one of your devices web browser to enter any authentication details required in the normal way. The service will see all of your devices as one device so you will only need to authenticate on one device. As for automating it, yes it is possible but you would need programming/scripting skills. Hope that helps Enjoy your trip!

[@donaldscottyperri8364]

Hi! I want to pick up a public wifi signal better, I almost get it in my home but occasionally the signal cuts out. I want to spend as little money as possible. Thank you! Scotty

[@chilkenito]

great thank you friend

[@techydiy]

Thanks for your comment

[@richiam1701]

+RUBEN CASTILLO (maestropirata) Hablas español ?

[@stefanos9831]

will this solution cut the bandwidth as repeaters do?

[@parjacpar3077]

can this be used to extend bt wifi with fon ?

[@techydiy]

Yes I. Did try that a while back. Also SFR WiFi (France) with a BT Fon login..

[@parjacpar3077]

Ive found a lot cheaper way of doing this by turning a pc in to a WiFi router which can also still be used as a normal windows pc

[@cepek221]

hi. can the same configuration repeat the weak signal line from wimax signal?

[@techydiy]

No, I don't think so.

[@cepek221]

+techydiy do you know how to?or where i can refer to?

[@techydiy]

You really need to give a lot more information about what you are trying to achieve. I would ask your service providers technical support or post the full requirement to a forum that deals with wimax.

[@subhajitchakraborty9405]

hey i want to cover a housing complex g+3 wifi and a area of 200x200 mtr ...what should i do....

[@techydiy]

+subhajit chakraborty I dont know, your question did not contain enough information, but generally if you need advice consider taking your requirements to a local networking company and see what they suggest. Thanks.

[@nazmify]

Hi can i install outdoor TP-Link WA5210G in a room and not outside and then would it provide a wifi signal in another building at a distance of near about 150-200 metres. If not then is there any device that can do so. And if yes how strong will be wi-fi signal. Thank you.

[@techydiy]

It depends on lots of different factors that affect the transmission path. Generally these devices work best point to point and line of site, any obstructions will reduce the range.

[@emperorubby]

Would this work for a secure public wifi hotspot that require authentication?

[@techydiy]

Yes

[@emperorubby]

I did not see a step in your video to authenticate to the secure network on the service provider portal. Do you have anything additional on that?

[@picklerick6759]

You didn't mention the conflict of IP's. It would be better to place it into a bridge mode or at least program the WA701D to use the WA5210 as the DHCP server. That way only one device is controlling ALL IP's. Otherwise you would need to create a separate network of IP's, (Your image of the configuration for the WA701D was on the .2 network NOT the .1 network) If that was intentional then I think you may want to mention that. (I would prefer a bridge mode OR just repeat the existing network) depending on your needs or situation. I just find either of those are easier as bridge mode allow FULL forwarding of any and all traffic to the WA5210, including DHCP requests. Of course the Repeater mode would just Re-Broadcast the signal to other devices a piggyback.

[@techydiy]

If I remember correctly it was configured that way to allow multiple clients to connect to one account on a WiFi service.

[@RebahanPremium]

can you help me ? I have CPE210 I had following the guide for using to AP mode but the problem I can't connect the wifi signals from the AP (CPE210) there's no connection anymore (like disable access) what should I do ?

[@deccanvintagebritishmotorc6385]

i have an open wifi near my house but icant fix the other pair of CPE on the building from which iam getting open wifi i tried a lot of tricks and right now iam having 2 15dbi tp link omni directional anteenas and they are connected in my modem but the signal till my house is very weak i dont know what to do can i fix one pair of CPE and connect it to my wifi router will CPE work in my case

[@abhishek00024]

Hi, i have outdoor CPE. and I want to extend wifi signal upto 2 km or more .

[@techydiy]

You would need to have directional antennas on both ends

[@demartinsm8479]

I agree. I just put up the 5210 model on the roof of my home and pointed it at another building 200' away. I was only able to pick up a signal of -74dBm. That's crappy. Not happy with this product.

[@georgewillis7849]

Gosh I sure wish I knew about this stuff. I'm just actually learning about it. Anybody have any ideas where I should start?

[@turayyusif1380]

Good morning to all my best teacher on internet, but how can i have full note on those modul

[@simplykrys4502]

Will this work on xfinty public wifi??

[@techydiy]

It works with most types of public wifi

[@0dra757]

Hi, I'm from Italy In my case I need an application to access at the public wifi network of my town. How can I bypass this type of authentication?

[@AbhinabDas86]

Is this going to work if my public wifi is on a different subnet?

[@techydiy]

Yes, it uses network address translation.

[@khalidanwary]

so what is the difference between TL-WA5210G and TL-WA7210N ?

[@techydiy]

Speed 54Mbps & 150Mbps

[@khalidanwary]

So if I buy any of those, then I also have to buy TP-LINK CPE210 as POE, right?

[@techydiy]

No they are both capable of POE. CPE 210 is a 2.4Ghz 300Mbps alternative.

[@lazerrunnerlibya]

Hi I'm using mikrotik routerboard 951 configured to generate a username and password . How can I configure my TPlink TL-WA5210G access point to extend the WIFI coverage in my coffee shop Best regards

[@DRGN1992]

hello..i clicked the reset button for E CCPE device but its not opening in default gateway 0f its 192.168.1.254 ...plz help me..how I can know / change the ip of my device . I forgot the changed ip of that device so I couldn't do setting.

[@NH-hf8yp]

Hi great video My WiFi signal is transmitted 100m to another area I can connect to Internet but an IP camera will not work any help would be fantastic.

[@picklerick6759]

Try to make sure the camera has the SAME IP and subnet and gateway as your network. Also check to make sure you have the DHCP enabled so all device can get the same IP info, If not, just make sure you place the camera into the same network as your router.

[@LeninRodriguezHd]

Hola, se puede utilizar un router como punto de acceso con la TP-LINK CPE510, sugerencias por favor.

[@lenovopieroit]

Lenin Rodriguez Hi, Hola tengo el mismo problema, con la cpe210, son de la misma familia.

[@panospan7678]

i do it my laptop can conect but my smartphone no can you help me

[@imcoolpiush]

range of repeated wifi??

[@alexclark9292]

Clear your cache

[@mikeatyouttube]

You configured the 510 to be a DHCP server starting at 192.168.1.101 but you then configure the 701 to have a fixed IP of 192.168.1.100. Why not leave it as dynamic and let the 510 provide the IP? I'm trying to use your video to boost a public Wifi AP using a CPE210 and an older cisco wireless router (linksys configuration software). The 210 default address is 192.168.0.254 (just to be different) and I connect the wire from the LAN port on the POE device straight in to the cicso router 'internet' input. The router's default IP is 192.168.1.1. Do you have a tip to get this config working? Should I change the router IP to 192.168.0.1 (and the gateway to 192.168.0.254)? Thanks.

[@techydiy]

If you assign a fixed ip to the 701 then you can access it's configuration via wifi without connecting it to the 5210. It just removes a potential problem and makes tracing faults easier. Both devices ethernet ports need to be in the same subnet to communicate, it doesn't really matter what it is, as long as its the same. So 192.168.0.1 sunet 255.255.255.0 and 192.168.0.254 subnet 255.255.255.0 is ok. Let me know how you get on.

[@mikeatyouttube]

Thank you for your help. The CPE210 software looks different to that in your video and by looking carefully at your video I determined I was not using the correct initial configuration. There is a mode called Client on the 210 but what I needed to select was AP Client (WISP). Once I'd done that everything started working much better :) My cisco (linksys) router has additional ports on it (unlike your 701) so I decided to leave the address of the router as dynamic (since I could always attach a cable to connect and reconfigure the router). But I shall remember your point about wireless connecting for reconfiguring.

[@regan220982]

Anyone can suggest me an idea.... I have internet connection in my laptop through usb stick and at present using connectifyme as a hotspot for my mobilephones..that ranges only a few meters... Can i use TP-Link CPE510 to supply internet from my laptop through ethernet and access in mobilephones for few hundred meters? Can i get clear wifi signal for at least 5km?

[@techydiy]

+Regan Jeya Antony A few hundred meters is possible, 5km is not unless you have two devices with high gain directional antennas. I am not familiar with connectifyme, but it may be possible to use this and an external access point like the CPE510 or simply repeating the wifi signal might give you the increase in range you are looking for.

[@digitalworld6649]

Sir how could i connect my 5210g to my router wirelessly?

[@vikasr2903]

can i use it as normal wifi router, if yes, what will be its range. i want to set up wifi zone for lan gaming with friends about 200 meters, is it possible with this device, if not can you tell me any other devices that i can use to create wifi zone of about 200 meters, one more thing how can we use tp link ant2424b 24dbi antenna with it, will it maximise my wifi range. antenna box say range up to 56km

[@techydiy]

+vikas R I assume your talking about the 5210g. Yes. The range depends upon the environment, 200m should be possible. The 5210g has an external antenna connector so you can use the parabolic antenna. Remember that the parabolic antenna will be very directional. The antenna built into the 5210G is pretty good.

[@vikasr2903]

+techydiy , yes im talking about 5210g, so it will work like normal wifi, like what we use in indoor

[@techydiy]

Yes it has 802.11 b/g. The wa7210n and cpe210 are some of the other external devices.

[@404Steff]

can you do it whit a TP-LINK CPE510 ?

[@techydiy]

The CPE510 operates at 5GHz, so yes if that's what you need. The config method will be different as well, but the principle will be the same.

[@404Steff]

Ok, tnx! :-)

[@menmencrafter178]

So I can with this device TP-Link CPE510 my wlan extended to outside (private network)?

[@lenovopieroit]

Hello form Italy, i need help about the configuracion. May i have your e/mail.Regard

[@berniebaatjies3382]

Hey there..I'm really a technologically handicapped idiot....Can anyone assist me. Me and my wife moved to my father in law farm and our house is about 30m from the main house. I was advised to purchase a TP Link CPE 510 to get the wifi from the main house at our house (30m away) After I purchased it I now see all these configurations and numbers that is frying my brain. I thought it just plug into router and plug into the new CPE 510 thing as instructed and we will have the signal. Please help. Do I have to plug it into a computer first and do all those numbers 🤯. Does the antenna have to be in sight of the house we are in. How far from the router can the antenna thing be. If it's really complicated maybe it best to get a new wifi connection from my service provider 😪 I'm just so blown away with all those numbers. Can you (anyone) please give me the most layman's explanation. Thank you very much in advance

[@andyopreshyn9811]

I understand nothing!

[@pekpsnkh3782]

TP link wa5210g

[@duguder]

Can I connect WA5110G directly(not wireless) to my chromebook ?

[@techydiy]

+Phong Nguyen yes, it has an ethernet port

[@kokosmokodokodoko2445]

evxaristo papapapara poliiii file mou eisai telios

[@techydiy]

Thanks

[@JasonOfWales]

confused as fuck

[@victormariera1361]

how do i connnect to a secured public wifi using this process?? WPA2

[@techydiy]

You would select the secured ssid with the survey button in the same way. Then you would set WPA2 and the password under wireless - security settings. ( I haven't tried it )

[@deepkhanderia5270]

Can u help me? I know my friends WiFi password but he is living 300 metres away from me and I have a TL-WA5210G with me so I can use his WiFi ? At my home using that above mentioned device? If yes then plz say me how to do it I have a router also in my home at it is TL-WR740N.

[@techydiy]

That's what this video teaches you how to do!

[@digitalworld6649]

@@techydiy but if i didn't connect the 5210g with my friend's router through wire may i connect 5210g wirelessly?