Thank you, finally someone actually shows replacing entire assembly and not just repacking the valves. I also appreciate your in-depth explanation on how you can tell if it’s a cracked pipe versus valving issues right up front.
@stephanieray6587 Жыл бұрын
It's a pleasure to watch a pro at work. Thank you, Hammerpedia guy 🙂
@CivilianDan Жыл бұрын
I love this guy. Great video. I bought his plumbing course and it was worth every penny. Thanks for everything sir.
@Hammerpedia Жыл бұрын
Wow, thanks!
@gmax75814 күн бұрын
Wow lots of respect for what a plumber has to know to do this kind of job
@oldporkchops Жыл бұрын
Good to know that this solder joint meets code and will stand the test of time. Thanks for sharing.
@m.w.h.9253Ай бұрын
I have a similar job coming up. I'm not a plumber but I'm not really watching to learn how to do the job but the little tips and tricks you gave while doing the job. Thanks👍
@TheDavidcrockettАй бұрын
One of the best videos to explain step by step. Great job
@garyjelsma8820Ай бұрын
You are an excellent plumber. And, you make an excellent video explaining all you do and why you do it. Very well done sir.
@Nappylox715 ай бұрын
Holy cow! I think this is one of the best videos I’ve ever watched. Plane and simple and to the point. Love the graphics too. Made me a follower today!
@c8089923 Жыл бұрын
Best plumbing instruction video I have seen. Just subscribed. I would have installed a 1/4" turn ball valve and access panel for future access. That's just me...
@garyjelsma8820Ай бұрын
Yes!
@fromdil64704 ай бұрын
Wow, you've done an amazing job here. Thank you for making things so simple. I had to watch many videos to understand what's going on, but yours was the best. I wish I had watched it earlier. Please keep up the great work!
@Hammerpedia4 ай бұрын
Thanks for the kind words
@ThomasOsseck Жыл бұрын
Excellent explanation and instructions. Thank you for making it sooo much easier.
@edrogers95308 ай бұрын
Many people drove cars with no antifreeze. Freezing water can crack engine blocks. happened to a buddy.. Good video. I replaced a frost free last year. Love this learning on KZbin.
@jeffreynolds91174 ай бұрын
Great video! I now understand the leak, how it happened and how to fix it. Great Job!
@Greyskydies8 ай бұрын
This is so clear! I really like these videos. Super helpful.
@rtel1238 ай бұрын
thanks for a good video, but wondering why not just solder a female threaded connector inside and screw in the new faucet? Saves the valve from solder heat stress, only that one solder joint, and might save another sheetrock cut later.
@attheendoftheday89695 ай бұрын
Good point. Now wondering about different options myself
@Ccb516lira4 ай бұрын
U don't understand its not supposed to be for next plumber present
@ernestorojo63332 ай бұрын
Yeah, but the next "plumber" could be the home owner that can just unscrew the fixture and then screw in a replacement. Job costs $20 and not $100s
@garyjelsma8820Ай бұрын
Very good suggestion!
@jhelpj8 күн бұрын
Excellent instructions in this video.
@MelissaMHarden Жыл бұрын
You’ve made this so easy to understand. Excellent video! Thank you!
@Hammerpedia Жыл бұрын
Thanks Melissa!
@kimchiman10005 ай бұрын
Thanks and looking forward to your follow up video on rebuilding one of these.
@lanettelopez1007 Жыл бұрын
Excellent Information! Thanks for taking the time to make this video. "God Wins" ❤️
@twistedj8083 ай бұрын
Im looking forward to your rebuild repair video
@danielvaeth93633 ай бұрын
Very good video demonstration
@Zenkai767 ай бұрын
this explains why my faucet was leaking behind my brick wall only when it's on. Thanks! have a like
@jmcguire566 ай бұрын
Great video! This helped me do my first hose bib replacement.
@Hammerpedia6 ай бұрын
Great!
@reymundoheraldo6281 Жыл бұрын
Good day sir, hope you make videos like this, it's so informative. Thank you for sharing your knowledge.
@Hammerpedia Жыл бұрын
Thanks for your kind words.
@MrGoncalvesful18 күн бұрын
Great video! Thanks a lot for sharing!
@DerickTharp6 ай бұрын
Great details/ installation. I’m trying to teach my 17 year old.
@jameskendrick6909 Жыл бұрын
Awesome stuff.
@Lewkie81527 Жыл бұрын
Excellent information!!!!!!!!!!!! Thank you!!!!!
@davidd5712 Жыл бұрын
Very well done I had to go thru almost the same on one i did
@Hammerpedia Жыл бұрын
Thanks!
@ibrocn4 ай бұрын
Fantastic and clear explanation. Thank you!
@MrKewlkid197 ай бұрын
Excellent display
@suespitz5195 Жыл бұрын
Awesome information!!!!! Thank you!!!!!
@dodgepolara727 күн бұрын
Where is the love button!!
@jmaus2k5 ай бұрын
Why not use the threaded connection so if this happens again they can just thread in a new spigot? Also did you measure the level and make sure it drains out? That is a critical step and that could be why it froze up in the first place.
@garyjelsma8820Ай бұрын
Good point!
@brendanroach65044 ай бұрын
Great video. Any thoughts on quarter turn valves vs the style you've got shown in this video? Thanks
@Cheerdad138 ай бұрын
Perfect video
@tkaramrai4 ай бұрын
Thanks a lot your video is very informative and helpful.
@kencolvin75539 ай бұрын
Your on the team.
@dariandarian955810 ай бұрын
What software do you use for drafting your plumbing videos ? I have a customer that I would like to demonstrate the planning/reviewing for his plumbing project 👍 Thank you for your videos! They are great
@FernandoRodriguez-ds5ri3 ай бұрын
Nice. New sub
@pugrolly7196 Жыл бұрын
Nice job dad
@Hammerpedia Жыл бұрын
Thanks Pugrolly 😁
@clintthornton1068 ай бұрын
Freaking awesome video man!
@AaronSheffield-j5y3 ай бұрын
Great video! Nice graphics also. How did you know it was a sweat connect vs threaded from the outside? I need to replace an outside faucet and cannot tell - afraid to crank it with a wrench to see and risk breaking it.
@gjcarrow18 күн бұрын
Holy Christ dude youre the man
@LoriBear-zx3pp Жыл бұрын
Great video!
@TomOsseck Жыл бұрын
Very helpful video, thanks!
@Hammerpedia Жыл бұрын
Gracias Primo 😂
@jamescarrillo81956 ай бұрын
Excellent explanation! Good work!
@socab2 Жыл бұрын
more videos! your explanations are great!
@sangyounhan257210 ай бұрын
This is amazing video bro❤
@michaeltammaro4826 ай бұрын
Excellent and informative - Thank you. My hose bib is leaking from the spindle when I turn it on EXACTLY as to your description of a burst pipe due to not disconnecting the hose BUT there is absolutely NO water coming into my inside wall where the housing passes through THANKFULLY. Frankly, I'm baffled. It's NOT coming from the packing nut. It LOOKS like it's shooting out from the holes in the spindle that turns (OPEN/CLOSE) within the housing of the hose bib assembly.
@garysimmons30239 ай бұрын
Great and thorough video. I’m confused thought because I didn’t see you adjust the slope. I thought the last one failed because it didn’t drain properly. Won’t this one fail too now?
@theironkiwi29485 ай бұрын
There is an angled spacer that goes behind the faucet, which creates the slope.
@KBiyce-ph2dz Жыл бұрын
Very helpful. Thank you!
@peggytappendorf9567 Жыл бұрын
Thanks for the information!!
@nicholasmarshall31915 ай бұрын
1st rate video! I have that same problem, but our kitchen cabinets were built around where the hose bib enters the house. 2 plumbers have looked at it and scratched their heads. Apparently, it cannot be replaced without tearing out some cabinetry. 😢
@richardshortz19475 ай бұрын
Nice video, I am trying to locate the heat barrier pad you used, not finding stick on types, thanks for any information you can share.
@jimmyfavereau Жыл бұрын
GOLD... thank Brother!
@Daniel-pm7np4 ай бұрын
Thanks a Bunch!
@fresh2death101010 Жыл бұрын
Amazing bro just hit the follow button 🎉🎉
@billk6952 Жыл бұрын
I like to clean the pipe BEFORE i make the cut..;)
@younangurgies69024 ай бұрын
Nice video. Where did you get those adhesive heat pads, and what is the brand? Thanks
@jamesedwards26876 ай бұрын
Great presentation. Thanks.
@mikel95246 ай бұрын
Great video! Thank you
@gabrielmartinez71918 күн бұрын
Crazy how he never posted again after this video
@kennethwood20892 ай бұрын
Bro--FWIW--I always use a big piece of white bread (no rust please!) to 'plug up' lines that have residual water in them before I solder. Like the line to your final coupling getting soldered. When done just turn on the water and the bread will liquify and disappear out the faucet when turned on.
@skydivingcomrade16486 ай бұрын
Extremely white bread stuffed in the water pipe is helpful to keep it dry and dissolves with water flow.
@donwolfjr1 Жыл бұрын
I guess I'm gonna need to replace my outside spicket now!! Excellent video and WELL done!!! I'm receiving your emails now but forgot to subscribe!! Lol. PS... I'm subscribed now!! 🙂😉👍
@Hammerpedia Жыл бұрын
Thanks for subscribing :)
@benoit18053 ай бұрын
That angle doesn't affect the join between the copper pipe and faucet when using shark bite??
@321chol7 ай бұрын
Hey @Hammerpedia how did you know it was a sweat connection before cutting the drywall to see it? And along that same thought, is it possible to find out if you have a screw in without being able to see the line inside the house? (i.e behind drywall)
@garyjelsma8820Ай бұрын
You cut the drywall to discover whether it's a screw fitting or other. You could do more damage if you start twisting from the outside when it's not a threaded connection. Good question.
@johnacosta14175 ай бұрын
Thanks
@rrd943415 күн бұрын
Can I get advice? My Frost Free Faucet is leaking from what I discovered is called a "weep" hole. Your diagram does not show this feature. What should I replace?
@jakecasper84165 ай бұрын
Can you use pipe connections without soldering?
@robertwaldvogel36197 ай бұрын
Mine isn't like that at all. Under a crawl space where I can't pull the pipe out and what I have there's no pulling the pipe out so I have cut the pipe where it is and try to install one where there's soldering.
@jamesscheidt4278 Жыл бұрын
Great job. Do you have one for a leaky one of these?
@Hammerpedia Жыл бұрын
Not yet, in the works.
@TheOtherDerek4 ай бұрын
We're all here because this faucet didn't work and now we have to replace it.
@pucktoad3 ай бұрын
Nah mine is just leaking due to age.
@wazkey86163 ай бұрын
Mines bent
@solracer663 ай бұрын
I'm dealing with a Arrowhead hydrant with a leaky stem that is threaded on the inside as well as the outside. There is a 90 degree elbow attached to it with threads on the hydrant side and a soldered coupling to a copper pipe on the other end. Ideally I just need to replace the stem but there are no stem kits for the length hydrant so I need to purchase the whole thing. Theoretically I should be able to unscrew the old hydrant but it's tricky as I don't want to apply force to the elbow. Alternately I could just strip the stem out of the new hydrant and leave the existing body in place. I am still deciding what the best approach is.
@mpxz9995 ай бұрын
My original spigot enters the basement JUST BELOW the plywood subfloor of the level above. This prevents me from achieving any kind of slope away from the home. In this situation, would I still a new hole, lower than the original spigots penetration, and then fill in the original penetration?
@HenryLinder-s9x Жыл бұрын
good
@NitinGautam814 ай бұрын
awesome
@r1kid51610 ай бұрын
What’s this software?
@Hammerpedia10 ай бұрын
sketchup
@filamfamadventures10977 ай бұрын
What would the charge for something like this? I am not looking for a formal quote just curious. I was quoted a little over $500.
@richardmitchell39782 ай бұрын
Why not put a joint in where the faucet can screw on in case of another failure down the road then the drywall would not have to be cut out
@KewlQT6 ай бұрын
I just cannot locate the inside end of my freeze proof spigot for replacement. I know it's inside the utility area of my basement but I have no reference points and so many wires & pipes in a small location. Any tips?
@Ommarrie4 ай бұрын
Do you guys have an email? I’m interested in to buying one of your books but it’s not a physical book. I was wondering if that option is available instead of a digital copy?
@Hammerpedia4 ай бұрын
Sorry we don't have a physical book at the moment, just the digital. hammerpedia.com/contact
@Bathygnostic3 ай бұрын
Thank you!! Sub!
@rawimpact2 ай бұрын
Insulate the copper pipe with foam so it doesn’t fail again
@cynkal120327 күн бұрын
you just explain the obvios. what if you dont have accses behind the foucet how do you remove it without breaking the pipe can you explain that ???
@darealmaul3 ай бұрын
Wait....so....should you not try to future proof that as much as possible for easier disassembly going forward? As a homeowner, I feel as though you should have utilized a different connection method(if it exists) for if ever the home owner is in this situation again. Now if it happens, the cutting procedure has to occur all over again. Is there not a design that us as homeowners can use that can just unscrew?? I noticed that there is threading on the pipe of the spigot, so that hints to me that there is. How come you didn't use that??
@davidbutler12097 ай бұрын
What if you have no leaks, but top of faucet is broke, has no cap for the top...
@vietcong4118 ай бұрын
Why not just unscrew it? Isn't the screw on piece soldered already?
@KE-op4vb Жыл бұрын
Why don't you use a shark bite coupling instead of soldering
@michaeltammaro4826 ай бұрын
What if in the future the housing (the whole hose unit), has to be replaced AGAIN? When you unscrew it from the wall and the water connection I would HAVE to believe a SOLDERED connection vs. a SHARK BITE connection would be less likely to leak when you're done. No?
@shannonbailey7580Ай бұрын
Mine has a cheap plastic handle i could easily break it.
@mikepollock59995 ай бұрын
Thank you so much for that super-helpful instructional.