How to Replace Control Arm Bushing 1996-2002 Toyota 4Runner

Buy Now!
New Control Arm Bushing Set from 1AAuto.com trq.video/ia-M...
New Control Arm Bushing from 1AAuto.com trq.video/ia-M...
This video shows you how to install a new control arm bushing on your 1996-2002 Toyota 4Runner. Rubber bushings help smooth out a ride, but are susceptible to wear or drying out and crumbling over time. This bushing is replaceable separate from the control arm, and you can replace it yourself.
This repair was done on a 2001 Toyota 4Runner SR5 3.4L Sport Utility 4-Door 4WD Automatic and the process should be similar on the following vehicles:
1996 Toyota 4Runner
1997 Toyota 4Runner
1998 Toyota 4Runner
1999 Toyota 4Runner
2000 Toyota 4Runner
2001 Toyota 4Runner
2002 Toyota 4Runner
Tools you will need:
• Pry Bar trq.video/oR9-...
• 19mm Wrench trq.video/oUy-...
• 10mm Socket trq.video/oa6T...
• 19mm Socket
• 21mm Socket
• Ball Joint Press
• Door Panel Removal Tool
• 1/2 Inch Impact Gun trq.video/osa-...
• 3/8 Inch Impact Gun
• Air Chisel
• Ratchet trq.video/obxI...
• Swivel
• Torque Wrench trq.video/oaBt...
• Bungee Cord
• Gloves trq.video/oY8-...
• Rust Penetrant
• Safety Glasses
• Silicone Paste
• Chisel trq.video/okx-...
• Floor Jack trq.video/o2X-...
• Hammer
• Jack Stands trq.video/oRS-...
• Sledge Hammer
• Wire Brush trq.video/osp-...
Subscribe: / @trq
Check out our playlist:
Toyota 4Runner 3rd Generation 1996-2002: • Toyota 4Runner 3rd Gen...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

[@Ashoud_Anobetah]

17:36 there is a cup slightly larger than the one on top that presses against the bushing flange and not the inner part of the bushing. I recently did this job and the kit had a cup that fit over the rubber and onto the bushing flange perfectly . Thanks for making this video

[@valectronica]

This bushing are similar as hyundai tucson 2.0 crdi d4ea diesel, thank you for this vídeo 👏, this tip is the most powerfull

[@dalemortensen1825]

Great video. You do such a good job with all your videos. Do you think it would be easier to sawzall the lip off the bushing and then press it out?

[@shadymaint1]

Ive done this job several times. Id rather just buy new control arms with the bushings altrady installed.

[@salvadoraguayo4361]

Thank you for your time.

[@rickyruwawyoch3864]

Main focus is the rust, tackle the rust first den throw in the good parts..