How to Replace Engine Water Pump 00-03 GMC Yukon SUV

[@1AAuto]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

[@halfcockedFame]

Your videos helped me replace the front end on my 01’ GMC Sierra 1500. Thank you. Now I’m on to the water pump.

[@chancafer]

KZbin is great, and it would be nothing without videos like this, thanks for uploading this, now off to the garage!

[@1AAuto]

You can feel the hoses before and after the thermostat to see if it's opening and allowing the anti-freeze to flow through the system. If the thermostat is old, it wouldn't hurt to replace it to begin with. They're usually only a couple of dollars. Hope this helps you out.

[@MrAvalanche316]

This video is awesome!! I had a water pump problem and followed it step by step this evening to fix my 02 chevy avalanche. I let it run for about a half hour while I cleaned up my garage and not one single leak!! I'm thankful to finally have the dreaded low coolant light finally gone. Thanks for this great video.

[@1AAuto]

@wavehog41 You may want to replace the thermostat and also try to relieve any air pockets that may be in the system. To do this (when the vehicle's cold) remove the radiator cap and start the truck. Turn the heat on full blast inside of the vehicle and monitor the level of the coolant inside of the radiator. It the level goes down top off the radiator with some fresh antifreeze. Hope this helps you out.

[@231MasseyFerguson]

Love this video! I have an '04 Silverado 1500 LS, 2WD pickup with the 4.8L V8. The truck hasn't gave me a problem yet and it has alittle over 90K miles on it. After watching this video, I know i can change the water pump when it comes time. THANK YOU!

[@1AAuto]

@MrAlnj06 I'm glad we could help. We carry many different kinds of water pumps for Chevy vehicles.

[@russglover9851]

Thank you very much for making this video! It saved me $350 replacing my 2002 Suburban water pump, thermostat, serpentine belt, and A/C belt.

[@warmothgmc]

Handy reference video I used to replace the water pump on my '97 GMC Sierra, but there were a a couple differences. #!, on the '97, no need to remove the tensioner pulley; but, the idler pulley did have to come off to get to the heater hoses. Removing the fan clutch was the biggest challenge. You MUST use penetrator to let it work into the threads to work it loose. I also used lock tight when I reinstalled the new water pump. A clutch bolt wrench is a must here. I used a 15" crescent.

[@tjdinfl]

Thank you for this video! I am not a mechanic (by trade) but am very mechanically inclined; I do all my own oil changes and most repairs. After seeing this video and all the steps made this so much easier! I normally would have saved this for the weekend but after watching, I knew I was going to knock this out this afternoon...2 1/2 hours...and I took my time because the truck was hot. Now, nothing to interfere with the gun show on Saturday! Thanks again.

[@SuperCyril2]

Great job Mike. Thanks for the video. Hey guys, this info is for anyone who's having their engine temp go above normal operating range after new pump install. This is happening due to the thermostat not letting coolant flow to the radiator. What I did to correct this was, first make sure engine is cool. Remove hose from top of water pump. Locate the overflow hose thats runs from the top of fill resevoir to the left side of the rad. Disconnect this hose from the rad. Go back to the hose you removed from the top of the water pump and hold the hose up so you can pour coolant in it to fill up the radiator until the coolant runs out of the hole where you disconnected the hose for the overflow on the radiator. Hook both hoses back up where they go and restart vehicle with the pressure cap off the refill resevoir add coolant as needed until proper level has been reached. Goodluck. Hope this little description helps you out. Cheers

[@1AAuto]

Thanks for watching. If any of our viewers need to make this repair we carry the water pump shown in this video on our website. We also offer free shipping on all orders in the US. www.1aauto.com/engine-water-pump/i/1aewp00021?KZbin&CTA%20Comment&ATony

[@amandalangdon5715]

SuperCyril2

[@blackfishblackfish]

Thank you. Replacing my water pump on my 2001 z71. 187K miles. Your video is just what I needed. Thank you, as money is tight right now, so I can't pay someone to do it, and I don't mind doing it myself, just need to be shown how.

[@brianharrison2357]

UPDATE: Thanks again guys on the video it was extremely helpful. The operation was a huge success thanks to your helpful tips. The only thing I had trouble with was getting the fan/clutch assembly off the old pump. It would slip so that I couldn't get any torque on the nut. I finally went to the store and found a "FAN CLUTCH SPANNER WRENCH". This tool saved the day ; it resembles a large flat open end wrench with two metal pins on the tips that went in to the respective holes on the pump pulley. This allowed me to get the necessary torque to remove the fan. Thanks again and I will be a regular user of of this site for both parts and repair advice! Sincerely, MickeyBro!

[@ScottWConvid19]

I love how you guys fast forward through all the tedious tasks that consume a lot of time. Your videos are super helpful. THANX!

[@1AAuto]

Thank you for watching. Please let us know how the repair comes out! 1aauto.com 888-844-3393

[@1dorepus]

You did a great job in showing us how change a water pump on a 2002 GMC Yukon. It was so easy after watching your video. One thing I think you should put in the video is the Air Compresor belt under the waterpump.Since your are there you might as well change the belt.

[@rossettielectric]

Hello and greetings form Bethlehem PA. Just replaced the water pump on my 2004, 2500 HD Sliverado 4WD@ 150,853 miles. You could not have made it any easier. I would not call myself a diagnostic genius at all,, but once I know what the problem is, I can usually replace the part. The video was exact, and I followed it to the letter. I just subscribed to your channel, great job!

[@1AAuto]

@BloodandSoil1 Usually when your waterpump goes bad it leaks anti-freeze from a small weep hole near the front of the pump.

[@imderrickjed]

The videos you guys offer are great. Ive been working on and building cars for 20 years and you guys are the only ones I see offering all the information needed. We dont do everything the same, but I have not seen anything wrong with any of the videos you offer. Great job guys!

[@1AAuto]

@Mr12mexicans Thanks for checking us out. Have a great day!

[@1AAuto]

That is correct. Most accessory items driver by the belt make a whining noise when they are starting to go bad (alternator or power steering are common as well) so double checking everything would be definitely recommended.

[@jaimemiller440]

Great video!! I do agree with one of the other commentators that the Large Crescent Wrench & Hammer need to be added to the tools list. Other than that I was able to follow the instructions and with the exception of a coffee break, was able to finish the job in about 2 1/2 hours. I did have trouble getting the fan off as easily as you did. Thanks so much for your video.

[@1AAuto]

If you're not careful and you mix Dexcool with the wrong anti-freeze it will clump up in the system. If you want to switch to regular antifreeze you should flush the system out completely, then buy a decent antiffreeze. I had to replace the radiator in my Jeep and just made the switch myself. If was a good time to do it, because I had to also replace the water pump and hoses. Hope this helps you out.

[@mryellowcrown]

THANK YOU FOR THE TIP A FRIEND AT WRK TOLD ME TODAY TO CHECK THE 2 FANS ALSO .. I MAY HAVE TO GET ENGINE HOT ENOUGH I DID 10 MILES FROM WRK TO HOME IT 78 TODAY HERE IN AZ ! BUT FANS DID NOT KICK IN WHEN I CAME HOME . (WARNING FAN MAY GO ON ANYTIME) SO I'LL TRY AGAIN .. THANK YOU VERY MUCH . I WILL LET YOU GUYS KNOW HOW THE OUT COME GOES .. KEEP UP THE GOOD WRK GUYS..

[@1AAuto]

@richcramify If you took the belt off you may want to put it back on, this will put some tension on the pulley so that you can break the bolts loose. Once you break them free you can take the belt back off and then continue removing the bolts.Hope this helps.

[@1AAuto]

The water pump bolts can be reused because they are not torque to yield. Also the water pump should have a gasket used if it is provided or in some vehicles, there is an O-ring.

[@tommymilam5032]

I😅

[@angelmacias8754]

good video I just did the same repair on my 2000 gmc sierra 4.8L saved some money by doing it myself thanks to this video why pay somebody when u can research the repair and do it yourself thanks alot for the step by step video!

[@1AAuto]

Thank you for watching. Glad we could be of help. Please let us know how the repair comes out! 1aauto.com 888-844-3393

[@1AAuto]

Great little trick for getting all of the screws in the correct places.

[@avguillen1]

Great instructional video! I just finish replacing the water pump, upper & lower hoses, thermostat, ac belt and the main belt on my 2004 silverado. I was a little leery on doing this work myself but after watching this video I felt confident enough to perform the job. All went well. Thank you very much. Great video's, keep up the great job..

[@iandukeman]

pretty nice video, I found it comforting to see each step, although nothing hard in this process it was good KNOWING there was nothing hard prior to starting...whole job about an hour for a first timer so seeing ahead really paid off...no hunting for "what's next" - Thanks a Bunch!!

[@1AAuto]

No problem at all. Have a great day.

[@robertovargas5340]

Highly recommend the videos these guys put out. Easy step by step instructions. If you are up for the challenge, you can not get it wrong with this video. Mechanic all my life and can speak from experience that the info these guys give you is precise and complete. I have not ordered parts from them but will be looking to give them a try next time I need to order parts. The videos, all I have to say is job well done 1A AUTO! Tampa Florida

[@1AAuto]

+Roberto Vargas Thank you for the great reply. We love to empower our customers by showing you how-to perform your own auto repairs while installing our high quality auto parts. Have a great day! 1aauto.com

[@CorruptedWorld100]

was going to pay to get this done but i never realized how simple it was this will be my project this weekend thanks guys!

[@1AAuto]

+CorruptedWorld100 A little know-how can go a long way. Please let us know how the repair comes out! 1aauto.com 888-844-3393

[@Ktonrider]

Great video!! I was able to replace my water pump today with ease thanks to your tutorial!! Bravo!!!! No more leak for my Silverado!!!!

[@1AAuto]

+Ktonrider Congratulations on the successful repair. We're glad the video helped you out. 1aauto.com 866-403-3393

[@1AAuto]

@danielbeaty The bulletin only applies to Savanna and Express full size vans.

[@1AAuto]

@ballershanelle It may have four small bolts that hold it on. If it does not, and has one nut in the center as shown in the video, than you should be able to use it using the same method. Hope this helps you out.

[@rotus7]

After watching your video, changing my water pump was a piece of cake!! Excellent job!

[@1AAuto]

Jason Kanak You’re welcome! Glad we could help 1aauto.com 866-403-3393

[@brianharrison2357]

This is awesome! You didn't talk like anyone watching was a dummy! It (the video) helped me think of replacing my water pump was not such a daunting task. It looks like it will be easier than when I replaced the pump on my Lumina! Thanks I will fill you in on the final results of my install. You guys are a life saver I will definitely recommend and use you in the future! Sincerely, Mickey Bro!

[@1AAuto]

Thank you for watching! These repairs are easier than most people think. Below is a link to the Water Pump for this application. 1aauto.com 888-844-3393 www.1aauto.com/1A/WaterPumps/GMC/Yukon/1AEWP00021?KZbin&Banner&OverlayCTA?VideoReply&VideoReply&ATony

[@1AAuto]

Thanks for visiting us on KZbin. Have a great day!

[@1AAuto]

The gaskets have those rubber pieces on them to seal them against the block. you can see them in red in the video. Hope this helps you out. Have a great day.

[@farmerdave286]

Thanks for making this video. I saved big $ and time by fixing it myself. Parts, new belts, coolant and a catch pan ran about 212 bucks for an 04 Yukon:)

[@wbadair2]

I was having a lot of trouble getting the fan off, but the tapping on the wrench with the belt on worked great! Thanks for the video!!!

[@1AAuto]

+Weldon Adair We're glad the video helped you out. Thanks for watching. 1aauto.com 866-403-3393

[@apexsrv]

Thanks for the vid. Saved me about $400 doing it myself...with your help. I'll be using you as a resource in the future for sure!

[@1AAuto]

As long as the water pump is not leaking, you should be fine. If by chance you end up having to redo the job, you should definitely make sure that the water pump is torqued down correctly.

[@1AAuto]

@krazor8 We recommend using the torque wrench, it is your vehicle so how you repair it is ultimately up to you.

[@1AAuto]

It looks like your on the right track. You may want to change the fluids, and give her a tune-up, also check the brakes.

[@1AAuto]

@blakegotanewface What you can do is WHEN THE TRUCK IS COLD, take the radiator cap off, blast the heat in the cab and start the truck. This will help any air pockets to find their way out of the system. Top the radiator off with antifreeze if the level drops, and top off the overflow tank. If the heat is still luke warm at best, feel the hose on the other side of the thermostat going to the heater core to see if it's warm. If it is you could try flushing the core with a hose.

[@1AAuto]

@mryellowcrown 210 still isn't all that high. You may want to take a look at the fan, if that's higher than it usually runs to see if it's acting up.

[@1AAuto]

@SoccaGal23 The chain should last quite a while longer, but if you wanted to put a new on in as perventative maintanence. It's not going to hurt anything.

[@stupidstt]

Just did this repair myself, this video was a great help!! Thanks.

[@1AAuto]

@1981shooter1981 We currently do not have an auto repair video that shows this particular repair.We'll keep this in mind if we end up doing this repair in the future.

[@1AAuto]

Yes you are correct. If it's worn you may want to replace it with a new one.

[@tiledave621]

Thanks! I did my water pump on my 04 Silverado last weekend. Thanks again

[@1AAuto]

+tiledave621 thanks for watching! 1aauto.com 866-403-3393

[@chitownbangin]

Another awesome and helpful video from 1A Auto. Probably all-around the most helpful people on the net!

[@1AAuto]

+Paul Bunyan Thanks for checking us out Paul. We carry the replacement water pump shown in this video on our website if any of our viewers needs to make this repair. Here's a link to them www.1aauto.com/1A/WaterPumps/GMC/Yukon/1AEWP00021?KZbin&KZbin&CTA%20Comment&

[@Mathius18]

Thanks for the great and detailed video! Much appreciated! 👍🏻 I replaced a water pump in a 01 Ram about 15 years ago and this video really showed me how much extra work I did just from lack of knowledge. My Sierra thanks you very much 😂

[@1AAuto]

+Matt C. Thanks for checking us out. Shop for high quality auto parts on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c

[@1AAuto]

If it's threaded you could use a little tefelon tape to help seal it up.

[@amzoeller]

This video is exceptionally helpful and took all the guesswork out of the job. 2 hours including clean-up, and all is well. I was not familiar with 1aauto.com, but will certainly check you out the next time I need parts. Thanks again!

[@1AAuto]

@Mr59strat You should be able to just use a thermostat gasket that comes with the thermostat.

[@silentbravo]

Just replaced my water pump yesterday, with help of this video. Great resource here! Thanks

[@1AAuto]

+silentbravo Thanks for watching. If any of our viewers needs to make this repair, we carry the auto repair part shown in this video on our website. Here is a link to them www.1aauto.com/1A/WaterPumps/GMC/Yukon/1AEWP00021?KZbin&CTA+Comment&LzBTC0SRk

[@EEnsign97]

Your videos are some of the most informative step by step videos out there. Ive used you guys several times and will continue to in the future. Thanks so much

[@1AAuto]

+Eric Ensign Thanks for watching. If any of our viewers needs to make this repair here's a link to them replacement part shown in this video on our website www.1aauto.com/1A/WaterPumps/GMC/Yukon/1AEWP00021?KZbin&KZbin&CTA%20Comment&ATony

[@jjsushi6234]

did the job. thx for a great video one tool a friend brought me was a hose clamp pliers. made the job quicker

[@48funkingrv]

Thanks for the informative video! Saved me $500 from the local shop. As others have said not that difficult more intimidating than anything. If it's an older vehicle go ahead and replace those belts and hoses. Since you have the thermostat out, might as well replace that also.

[@1AAuto]

@valtierra2966 There could be an air pocket in the system somewhere that keeps making the fluid level drop, or you may also want to pull the dip stick to see if any gas is getting into the oil.

[@juangarcia4465]

Hey you A1 deserves a high five. .. thanks man . .. exelent job . U are a good help..

[@1AAuto]

Thanks for watching 1aauto.com 866-403-3393

[@cwinaz5862]

Thanks for the video. I was able to do replace the water pump myself. I used the clamp method to keep the fan belt from moving and a pipe wrench to remove the fan clutch. I had good leverage with the pipe wrench and the fan clutch loosened very easily.

[@1AAuto]

You may want to take a look at the pulleys and motor while it's at idle to see if anything seems to be off.

[@gamesa777]

Gracias 1A auto: con sus videos hacen que se mire tan facil y la parte mas mejor es ,cuando terminas y todo sale muy bien . gracias a ustedes 1A auto. Installe water pump.

[@1AAuto]

Thanks for watching. Have a great day! 1aauto.com 866-403-3393

[@1AAuto]

@surfflyfish4striper Yes these require the Dexcool or compatible antifreeze.

[@xUNLUCKYxSEVENx]

thank you so much for this video, they were trying to charge me $650 for this at the shop, so i ended up doing it myself, bought all parts brand new, also bought a new alternator, and an econ book for college all for about $500

[@1AAuto]

+Saul Sanchez We're glad you found utility in our video. It sounds like you made the rational choice. 1aauto.com 866-403-3393

[@1AAuto]

You should run what's recommended for the vehicle. You may want to flush the system out and replace the anti-freeze if it has over 100,000 miles on it.

[@1AAuto]

You may want to take a look at the heater core to see if that's the issue.

[@davidg9167]

This video help me to replace the water pump on my 1997 K1500 4.3. Not quite the same but close enough. One whack (or two) on the fan nut didn't do it for me. I kept at it for 5 minutes and grabbed the belt to help it stop moving but finally got it. The hardest part was getting the bolts started on the replacement pump, it's tight and down low on the 4.3. TYVM.

[@1AAuto]

Thanks for checking us out. 1aauto.com 888-844-3393

[@aaronyanez]

Awesome video. I always look your videos up before I start a job just to double check if there's anything that'll surprise me. Your videos are the best. Thanks for posting.

[@1AAuto]

Thanks for the kind words. Glad to hear we could help you out. 1aauto.com 866-403-3393

[@peterhorn9934]

Thanks for your video. This was my first auto repair, and you made it easy. You have a great price on the water pump, too.

[@1AAuto]

I currently don't have those specs to look at. As long as everything is snugged up fairly well you should be okay.

[@popeyeandy959]

Mostly a realistic video of the job. I like how you don't edit out things like dropping a bolt (which probably rolled to the exact center of the truck - as they always do). I say mostly because I've never heard you curse at a stuck bolt or a slipped wrench. LOL. Nice job on these videos

[@1AAuto]

Normally the belt making noise either means coolant got on it and now it is is junk or it could just be from old age. At this point I would suggest replacing the belt with a new one.

[@craigkrage2689]

Thank You guys for another clean cut instructional video.

[@1AAuto]

+Craig Krage Thanks for checking out our videos! If any of our viewers need to make this repair, we carry the part shown in this video on our website. Here's a link to them. www.1aauto.com/1A/WaterPumps/GMC/Yukon/1AEWP00021?KZbin&CTA%20Comment&ATony We also offer free shipping on all orders in the US.

[@timmorford6711]

This video made it very simple for my father and I to do (he watched, but gave guidance as I did it). By having laptop on the fuse box of my 2003 Silverado, we easily were able to stop and go by how the video was done. Many thanks!

[@1AAuto]

No problem. We're glad the video helped you out. 1aauto.com 866-403-3393

[@1AAuto]

It may be. If it isn't and that pulley is bad, you sould replace it anyway, because what will happen is that it may fail on the road and throw the serpentine belt off of the motor (had this happen before), luckly wasn't far from home and was able to limp my truck back.

[@sreilly]

Great video. I'll be replacing my water pump on my 2003 Silverado tomorrow. Thanks!!

[@1AAuto]

There should be a weep hole under the water pump that it would leak from when the water pump fails.

[@1AAuto]

The water pump comes with the gaskets for the pump. We do not carry a thermostat for this vehicle.

[@RicJac]

Mission accomplished! 2001 Silverado LS 5.3 10/4/11. Thanks!

[@scottbender4936]

Great video, it walked me right thru it. Just be sure your adjustable wrench is big enough when taking off the fan. My 10" wrench was too small, I had to use a pipe wrench.

[@briankowald6465]

Thanks for the video it helped me out. Mine was leaking from the gasekt on the left side. It was incorrectly installed at the factor. No telling how long it has been leaking. The original gaskets were just the red squares with nothign to hold them, so they slipped during installation. The new one I installed had copy gaskets with rubber square inserts.

[@brio2323]

Great job bud! I'm very impressed with the detail you went into. I will be sure to pass this video to my friends. Hope to increase the traffic on your site. Thanks again!

[@Gdawg685]

man thanks im only 16 and i did it all by myself very good video

[@FireEater]

Great video with good lighting,a pleasure to watch. Thanks

[@1AAuto]

Thank you for watching! 1aauto.com 888-844-3393

[@chadwelsh9513]

You guys rock! You help me make money period point blank.

[@MrAlnj06]

This video is absolutely great!!! Thank you for taking the time to record and post.

[@akabigo135]

Great video! It helped me out immensely! Since I'm a novice, the job took me about 2 1/2 hours! I could really use a video on changing out the front hub/ bearing ABS sensor. Thanks!

[@IamAmerican69]

Thanks, Your video helped me remove and install a water pump, on my 1999 Gmc Sierra.

[@1AAuto]

You're welcome

[@bobjones3846]

Be sure the new pump has all the parts ,Mine came with out the gaskets, e-mailed them on that . Mike Green is wright 1a auto is GOOD on what he says , They took good care to send me another pump in two boxes to be sure I got all my parts I ordered.

[@1AAuto]

+BOB Jones Thank you for the feedback. We're glad to hear you contacted us and we were able to resolve the matter. 1aauto.com

[@torrescesar71]

good video. how do i know if the water pump is bad. my tahoe start to leak coolant from the water pump but dont know if its just the seal or the pump its bad

[@MrKaarons]

Wow what an awesome video. I do have one question though. Can the thermostat be replaced by putting it on the water pump while it is still outside the vehicle? It seems like it would be a bit easier to do it that way and then install the entire assembly.

[@WxManII]

Yes. Also, the thermostat housing can remain attached to the water pump during removal.

[@1AAuto]

@warmothgmc The 5.7L in the '97 is somewhat of a different beast.

[@ryanhowell6537]

Great video! Thank you for the "tips and tricks" Pretty easy job but it's nice to have a video to walk you through it!!

[@1AAuto]

+Ryan Paterson You're very welcome!

[@1AAuto]

@TheBubbles069 We currently do not have an auto repair video on that particular application. If we make this repair in the future we'll keep this in mind.

[@TopwaterTony]

great video.. im going to tackle mine this saturday !!

[@swss12]

noooooo!! not the dex cool.. haha never heard anything good bout that stuff. anyways great video. it's gotta be the best DIY ive seen. cheers