How to Replace Front Outer Tie Rod 92-00 Toyota Camry

[@1AAuto]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

[@johnbruin5547]

Note that he said use a 17mm socket to loosen the old castle nut but then said use a 19mm socket to put the new castle nut on. I have seen when new replacement nuts sometimes have a different outer wrench size than the old nuts for replacement parts.

[@williamclick9771]

I'll check mine. It's a 2000 Camry LE 4 cylinder. Thanks much for the video.

[@7vanzzy7]

Doesn't wanna fit back in the spindle too easily. Can i hammer it in?

[@AmerShojaei]

Good luck my friend 🎉🎉🎉🎉🎉🎉🎉

[@ZenRyoku]

I ordered this part from 1A auto, and it was NOT the same tie rod that is featured in this video. the rubberized boot on this outer tie rod is more elongated and more cone shaped. also... there is no metal point on the other side of the tie rod as well.. Im changing the part right now... ill update later whether or not it makes any difference.... ...im sure its not a big deal... but these are the little discrepancies that DO matter occasionally.

[@Scouty208]

Is it possible to break the cotter pin? I haven't been able to get mine off after trying for 10 minutes and I'm afraid I might break it.

[@brizad187]

I don't know if you will get this in time. I just got 2 tie rod for both sides.. the tie rods look completely different. is that ok? or did I get the wrong part by mistake.

[@1AAuto]

+brizad187 If it is a part that you had ordered from us; if you would like to call our sales staff at 888-844-3393 we can take a look into your order for you. Hope this helps you out. 1aauto.com

[@brizad187]

1A Auto Parts I emailed.. called .. I text them on Facebook. they keep saying they will look into it.. I went to advanced auto juat to ask them. they said they believe it's right...I've been waiting days.. I order my ball joint for my truck a while back.. it went bad already.. I need another one of them also.. I missed 3 days of work just trying to get a answer. and it's prob the correct ones

[@1AAuto]

+brizad187 If you would like to call our sales staff at 888-844-3393 we can take a look at your order for you. 1aauto.com

[@SvsRyder]

Do you have a video for the replacing of the transmission mount ?

[@luisbriano8506]

They do

[@kenjenkillasounds]

What are the symptoms of bad tie rods I already have replacement ones ready to go in but only based off my mechanic saying I need them

[@Axe0403]

When you go over bumps you feel your car wiggle, another is a loose steering wheel when you make turns

[@allenpruett5525]

Any reason why my new tire rod end didn’t come with a new lock nut or a serviceable joint?

[@1AAuto]

+Allen Pruett If this is in relation to an order placed with us, please contact our customer service department so we can assist further with this.

[@farazsm2013]

What is the reason for torquing the axle after installing the wheel and lowering the car than before it?

[@1AAuto]

+farazsm2013 Thanks for watching! It is not safe to apply that much torque when the vehicle is on jacks and jack stands or on a lift. You need to have the vehicle stable and on the ground, suspension loaded.

[@justty394]

How would you take off the castle nut that keeps spinning but won’t come off??

[@1AAuto]

+Tyee cooks It sounds like the ball joint stud is spinning along with the castle nut. You will have to get some vice grips on the end of the stud and remove the castle nut with and open ended wrench. 1aauto.com

[@justty394]

Thank you very much this helped my problem

[@brunoverano3066]

Will this be the same steps on a 2002 Toyota Camry?

[@1AAuto]

+Bruno Verano At this moment, the closest how-to video we have to your request is for this vehicle, which is very similar to the one you have. The steps may not be 100% the same, but should contain an adequate amount of information necessary for accomplishing this task! 1aauto.com

[@brunoverano3066]

@@1AAuto thanks!

[@SportsMusicCars]

Our passenger side outer tie rod is FROZEN in place. Used PB Blast, MAP heat and the two wrench method - NOTHING. No movement at all. Only a shop with a rack and an extra long bar for leverage is gonna free it.

[@CoinHuntingDrew]

5:00 What's that black bar below the tie rod?

[@1AAuto]

+CoinHuntingDrew The black bar below the tie rod would be the sway bar.

[@larryclark1281]

My tie rod won’t come out and the castle nut is starting to mushroom

[@1AAuto]

+Allen Pruett Thanks for the tip!

[@juanpacheco8654]

what is that bottom bar called?

[@1AAuto]

+Juan Pacheco It sounds like you might be referring to the lower control arm. 1aauto.com

[@juanpacheco8654]

+1A Auto Parts at 4:37 you are pointing to the inner tie rod. I am talking about the bar that is right under the one you are pointing to.

[@1AAuto]

+Juan Pacheco Ok, that should be the sway bar. It looks as though it is a different design on this vehicle. 1aauto.com

[@juanpacheco8654]

+1A Auto Parts do you have a video showing how to replace that sway bar then?

[@sipmeister3611]

do not use a hammer ......

[@lastingrod56]

This says tie rod, NOT tie rod (END)!!!!!