How to Replace Rack and Pinion Assembly 92-01 Toyota Camry

Buy Now!
New Rack & Pinion Assembly from 1AAuto.com 1aau.to/ia/1AST...
1A Auto shows you how to repair, install, fix, change or replace a broken, busted, bad, loose, or damaged rack and pinion. This video is applicable to the 92, 93, 94, 95, 96, 97, 98, 99, 00, 01, 02, 03, 04 Toyota Camry or Avalon or Lexus ES300
This process should be similar on the following vehicles:
1997 Toyota Camry
1998 Toyota Camry
1999 Toyota Camry
2000 Toyota Camry
2001 Toyota Camry
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/osy/1AX...
• Pry Bar 1aau.to/ofj/1AX...
• 12mm Wrench 1aau.to/ofc/1AX...
• 14mm Wrench 1aau.to/ofc/1AX...
• 19mm Wrench 1aau.to/ofc/1AX...
• 22mm Wrench
• 12mm Socket 1aau.to/osz/1AX...
• 14mm Socket 1aau.to/osz/1AX...
• 17mm Socket 1aau.to/osz/1AX...
• 19mm Socket 1aau.to/oii/1AX...
• 21mm Socket 1aau.to/oii/1AX...
• 22mm Socket 1aau.to/oa8/1AX...
• Vise-Grips
• Channel-Lock Pliers 1aau.to/oaT/1AX...
• Needle nose pliers 1aau.to/ocS/1AX...
• Needle nose pliers 1aau.to/ocS/1AX...
• Torque Wrench 1aau.to/omm/1AX...
• Marker / Writing Utensil
• Rust Penetrant
• Drain Pan 1aau.to/och/1AX...
• Floor Jack 1aau.to/ofF/1AX...
• Hammer 1aau.to/ofg/1AX...
• Jack Stands 1aau.to/ofh/1AX...
• Measuring Tape
Subscribe: / @1aauto
Check out our playlist:
Toyota Camry 1997-2001 4th Gen: • Toyota Camry 1997-2001...
Toyota Auto Repair Videos: • Toyota Auto Repair Videos
For More Info visit us at 1aau.to/h/EI/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@1AAuto]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

[@JuanYRuby1209Marine]

Great video. I have one question. What type ans size bolt is it the one you remove from the rack? Where you use an extension pipe. Mine fell off from my 01 toyota solara, I'm petty sure they are most the same engines.

[@RrRr-th1kf]

Is the rack steering of camery 2005 is same genuine OEM part ? Or its brand of company A1 auto???? How much cost shipping to Bahrain ?

[@racerrick35]

One of the best instructional videos I've ever seen. Plenty of light, great camera positioning, and clear English communication. Very impressive! Two questions; 1) why was the bumper removed, and 2) HOW LONG SHOULD THIS JOB TAKE (on jackstands)?

[@1AAuto]

+Rick Poage Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

[@dougbarker293]

This is the best automotive repair video I have ever watched Well done

[@1AAuto]

+Doug Barker Thank you for the great reply. We love to empower our customers by showing you how-to perform your own auto repairs while installing our high quality auto parts. Have a great day! 1aauto.com

[@breerosky9204]

Thanks for this excellent video! I'm a novice and currently working on installation on a '98 Camry. One recommendation thus far for the video is pointing out the easier alternative of using a ball joint separator to remove the tie rod ends from the spindles if they are really stuck in there. I pounded the crap out of one of the castle nuts before realizing I could just get this tool for less than $20 and do it in a couple of minutes.

[@Hippoteetomus]

I’m working on a 96 right now and the rear motor mount is blocking the bolt for the steering rack clamp and I can’t get the motor mount out because there no room!

[@jerryhatfield7650]

Hi I followed your video to a T on my Camry and everything went beautifully I appreciate the videos you guys make. I have a question though when I completely turn the wheel to left or right all the way the stops my Camry makes a squealing noise. there's a lot of misinformation on the internet and I'm kind of hoping you can clear this up what may be causing this noise! Is it a loose belt is my rack defective or is it a pump issue? Other than turning it to the complete left to right the rack is working beautifully!

[@dylanstoll9681]

Sounds like the belt for the power steering pump. To tension the belt you have to loosen the pivot and lockdown bolts on the pump, pry it away from the engine, and the re-tighten the lockdown bolt while you keep tension on the pump. You may also need to replace the belt, check it for cracks or wear.

[@nutsandbolts7407]

Doing this right now...and this is a very helpful video...

[@notrickyspanish1441]

Very good videos. I replaced my 2002 honda civic radiator today with one of their videos and now I'm doing my Camry thanks a lot guys.

[@sweathe3819]

Thanks for the video, I was able to do this repair. A couple things, the rack came with both bushings, so I didn't have to do the bushing change shown in the video. One of the main bolts would come out, I had to cut it out with a grinder - looked cross-threaded. Also, I ended up taking it out and putting it back in four times to get it right. So, yes, you can do this, and save hundreds of dollars, but it ain't easy.

[@1AAuto]

+S Weathe Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1AAuto.com

[@jeromeduffy9270]

4 times

[@e.o.s.470]

Thank you for an excellent video. One thing that I didn't see(pertaining, at least to a 1992 Lexus ES300) is the fact you have to loosen the clamp around the black baffle of the steering column(inside passenger compartment) and then pop out the center cap that is around the steering column shaft and loosen the 12mm bolt holding the splinned shaft, push the shaft into the steering column coupling and then you can easily slide the connector onto the rack spline shaft. If you don't do it, it's nearly impossible to separate the connecting point from column to rack.

[@ReyLaFleur]

U forgot to say use a HEAVY AF hammer to release the tie rod....I had to use a jack to put upwards pressure and a sledgehammer to knock it loose

[@nutsandbolts7407]

Or just use a tie rod puller/pitman arm puller ...works like magic

[@496elcamino2]

That was a clear and understandable R&R, thanks guys.

[@norcoauctions]

after watching this, I may have to sell my camry now

[@realskater31]

I'm doing it right now on my avalon no biggie minus the yoke for steering shaft

[@west_park7993]

do not use vise grips on the sway bar link. there is hexagonal hole in the nut for allen wrench. use allen wrench and 14 mm box wrench

[@nsummy]

Does anyone else like the background music of these 1A videos? Its like a combination between the Jason Bourne theme song and a porn. Makes me feel badass while I'm fighting rusty bolts on my 99 corolla.

[@1AAuto]

Thanks for checking us out. 1aauto.com +Nick Summy

[@mightymoe4u2]

Just did a 1996. The steering intermediate shaft does not collapse enough to remove it, i dropped the back 2 sub frame bolts to make enough room to remove that shaft and on the 96 you will need this room to remove the 2 rack 19mm bolts. The setup is not the same on a 96 with a 4 cylinder as what you are working on

[@1AAuto]

Thank you for the feedback! +mighty moe

[@DavidHernandez-ue4fz]

How many hours you done? I just trying to it on a 94 camry 4 cyl but I got scare.

[@justcn09]

I've run up against the two 19mm mounting bolts. I'm gonna have to get the car up higher so I can fit a 24 inch pipe on my socket wrench. Like he says, it can be done on jack stands. But a lift makes it 10 times easier.

[@user-we8zl1ij5d]

The very best instructional video I've ever seen! I'm feeling pretty confident to tackle this thing on my own. I will let you know how it turns out... :)

[@1AAuto]

+Jamie Kirkham Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

[@spikespergel4940]

I wish you could show how to get the steering shaft off the rack splines better. Do you just hammer it up and off?

[@rontakabuda4474]

Very helpful video,👍👍Thank you so much.🙏

[@ahmadjahan4213]

Comparing to other Video in YT, you've done pretty damn good job I must say. TY

[@billysanders3143]

1Aauto is the best out here show how

[@siskip]

Helps to take the o2 sensor out of the way.

[@efrainr.rodriguez596]

Hi do you have any video replace and rack and pinion Toyota Camry 2014

[@benjaminfuentes1618]

Great explanation and illustration. From Puerto Rico, Benjamin Fuentes

[@jonsalido2382]

Great Video! Good step by step instructions, I was able to replace rack and pinion assembly on my 2001 Lexus es300...it is practically identical, THANK YOU!

[@t.g.c9311]

i have a 2007 solara convertible. all was relatively ok for me until I tried getting the high pressure lines back in. not threading in for me. any tips?

[@VENUEATHENS]

None of the pressure lines were replced with the rack?

[@qrs_tuv1925]

Excellent production.

[@latinainthecity9648]

The slow motion power steering fluid spill was funny....double entendre?? Haha

[@sanchezsanchez5744]

good video friend rack & pinion of toyota avalon 2004 fits for toyota camry v6 2000

[@Agustus824]

Quick question, is there a “how to” video on how to replace the rack on the left? Mine seems to be leaking, need help! Thanks

[@1AAuto]

+Gustavo Avila We currently do not have an auto repair video on that particular repair. Thank you for asking. 1aauto.com

[@AppleAK47-sf4ev]

Can you make a video for a 2001 - 2005 Honda civic

[@west_park7993]

i can disconnect the muffler connection and remove the 4 19-mm bolts that hold the subframe. This way it makes more room for work. Is it worth?

[@carlincedras6881]

after replacing my ecu on my 2001 toyota camry the security light came on solid and the car doesn't want to start. please help

[@jimpeveler7574]

Very Good video where are the better ones that I’ve seen give you an a plus

[@1AAuto]

+Jim Peveler Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1AAuto.com

[@firebird14420]

If I did push in the inner tie, you said you'd have to center the rack intermediate shaft again to be centered, what would happen if I didn't? Could I take it to a alignment shop and them still fix it? Because I did and my steering wheel was way off. I told them I may of had the steering wheel off and rack shaft not centered and he said his computer would tell them all and could fix it. Is this true or should I take it all back out and do it the way you say and go get a alignment again? Thanks!!

[@firebird14420]

Can you help me with this? Should I redo the whole rack and center steering wheel and rack and get it aligned again? Thanks again!

[@johanngarcia7290]

appreciate it this videos guys....keep goinggggg!!!!

[@1AAuto]

+Johann Garcia Thank you for watching. We will keep going as long as the feedback keeps coming in, and the requests pile flow through! 1aauto.com

[@benghez5608]

Hi it is a very instructive video, but you have not shown what brand of fluid you have used for the power steering. Because there are few brands in the market besides Toyota brand. Thanks

[@BenDover-lx1gh]

Does this fit 2000 Toyota solara sle v6 been looking at your page but says it does not fit and cannot find it on there even if I enter the correct information

[@nameentered8501]

Ive been a tech for over 12 years and toyota requires atf/dex3 not ps113 or standard power steering fluid with what looks like gm and or honda ps fluid. The rest of your video was on point and i want to say well done. But fluid types matter

[@gballa2730]

I've noticed where the 19 mm bolt goes that piece of medal that the bolt goes through has detached from that cross member.. What can I do about that??

[@miguelgutierrez8054]

Thank you very much for all the videos! I have a question and can't seem to get the answer. What do I do with all the old parts? I don't want to dispose of them, if I can get paid for them by recycling? I can't seem to find a place that does it, so my question is, are the Rack and Pinion, Struts, Whole knuckle assemble just scrap or can i get recycling money for them?

[@mannyman874]

Dude hell of a job.!

[@1AAuto]

+mannyman Thanks for watching. If any of our viewers needs to make this repair, we carry the auto repair part shown in this video on our website. Here is a link to them www.1aauto.com/rack-and-pinion-assembly/i/1astg00003?KZbin&CTA+Comment&At7tChYYvY

[@TheRichard4098]

I could not find your video on this same car that shows how to align the steering wheel like you said in this video, can you share the video are tell me exactly how to align the steering wheel like you did the rack? thank you

[@donaldmussaw2982]

I notice a bit of FF on removing the clamp from the spline. If neither one moves (rack or clamp, how was this remove without allowing the rack to move away from the clamp?

[@rontakabuda4474]

Very helpful video,Thank you so much👍👍

[@raph11spd]

I have a question I'm doing this project on a chevy tracker and we're at the point of re connecting the power steering lines to the rack and pinion. we're not sure which one was the top and bottom line.... does it matter their positioning?

[@ranapratapsingh3416]

High quality video. Good.

[@kim7018]

Why do you disconnect the oil lines before setting the steering wheel? Is this not stressing the steering pump?

[@sw3attynipps]

I’m getting ready to change out my 94 Camry rack and pinion but there are two different racks that could have been used depending where the vehicle was assembled. One was North American and one was Japan and are left side drive. Can you tell us which one you worked on? Great video btw.

[@1AAuto]

+Speedy Banana Thanks for the inquiry! This part fits all 1992-2001 Toyota Camrys (left hand drive). Please let us know if you have any additional questions.

[@nultari1]

I can’t get those 19mm bolts off…. Unless I lift the car much higher and put a pipe over the breaker bar. Also struggling to separate the spline after removing the bolt

[@svlotoy]

What's the toque spec for the bolt from rack to frame???

[@dingodyno9016]

would this be the same process for a 2003 Toyota Celica GT?

[@thomassmith2056]

paid 987 for 96 Camry steering gear remove and replace at shop. free oil change,lol. yes, it ain't cheap. oh, had outer tie rods replaced to as it comes with inner.

[@seahawk9435]

Say you can be done with a jack stand but you used a lift how you use a long breaker bar with jack stand

[@danbeuscher14]

When tightening those links, there is actually a torque hole on the back side you can use instead of clamping a vise grip on it.

[@1AAuto]

+Dan Beuscher Thanks for the feedback!

[@ptkrishanmaharaj3917]

Video Very nicely done in detail Thank you💖👍

[@jayt1784]

This video saved me hundreds of dollars and I learned so much. Thanks.. 1998 Camry 225K

[@jorgevillegas3663]

Jay T Excellent tutorial thanks

[@1AAuto]

+Jay T Thanks for watching. If any of our viewers needs to make this repair we carry the part shown in this video on our website. Here's a link to them www.1aauto.com/rack-and-pinion-assembly/i/1astg00003?KZbin&CTA%20Comment&ATony

[@qualityreno9689]

good job. thank you for postimg this

[@1AAuto]

+Quality Reno Thanks for checking us out! 1AAuto.com

[@christopherkrause3255]

How long does it take

[@jamest163]

what happen to my angel sensor always faulty after replacing rack and pinion?

[@vulcan03]

Did what was shown but the tire shop said the wheel needs adjusting more to the left because it's too much to the right? How to adjust so it's just right with the rack, thanks.

[@vulcan03]

*steering wheel

[@1AAuto]

+vulcan03 Thanks for watching! It sounds like the steering rack may not be centered. Please follow the process shown at the 20:00 minute mark in the video. 1aauto.com

[@carlosfigueredo3327]

this is a very profesional video i liked a lot . it look like a movie.

[@racilpz5753]

Can you do do piston ring please man my car is burning old

[@riperoni861]

Is this the same vehicle as a 2001 Lexus es300

[@supercharged517]

would I be able to just turn the new the steering rack all the way to the right along with the steering wheel before installing it instead of trying to center it ?

[@1AAuto]

+Brian Leabo The alignment will still more than likely be off. You should install it in the same position as the factory one. 1aauto.com

[@nathanield.4527]

There are o-rings needed for installing the lines at 25:22 which are not included with the rack and pinion and 1A Auto does not offer the o-rings for sale. Make sure to purchase a new set of o-rings from the stealership before you start your replacement.

[@joebriggs9599]

Great information how do you lock the steering wheel just by putting wheel to center and turn key off? or use a strap also?

[@1AAuto]

+Joe Briggs Thanks for watching! Just center the steering wheel like he shows you in the video and turn off the car. You do not need to us straps or anything like that, it should stay in place. 1aauto.com

[@GermanBlueMax]

The tie rod bolt, where the castle nut goes, is just spinning when the castle nut gets to a certain point. How do you keep the tie rod bolt from spinning while getting the castle nut to 35 ft lb torque?

[@martybeach6704]

Put a hydraulic jack under it and put a little pressure on it and give the outside of the casting a couple wraps with a hammer as you tighten

[@narachan291]

Can you show me Rack and Pinion Assembly Toyota 2003 Highlander V6. I want to made it

[@1AAuto]

+nara chan We do not have a video for this repair right now, but we'll keep this request in mind for a future video! 1aau.to/m/Shop-1AAuto-c

[@eugeneflintroy5555]

Why not center the steering wheel before taking any thing off?

[@Reebang]

Excellent video

[@Lasurge1982]

I have 2011 Toyota camera hybrid. Is this process pretty much the same for that year model ?

[@1AAuto]

We currently do not have an auto repair video that covers this particular repair. We will keep this request in mind in the event that we need to make this repair in the future. 1aauto.com +Lasurge1982

[@brent52]

Hi Do you have a how to video for RACK N PINION replacement for 2008 Honda civic sedan

[@1AAuto]

+Brent Hannon We currently do not have an auto repair video that covers this particular repair. We will keep this request in mind in the event that we need to make this repair in the future. 1aauto.com

[@jtee2860]

Amazing job! Would this be the same process for a 91 lexus ls400?

[@1AAuto]

+j tee This procedure might be different for your application. We do not currently have a how-to video for this particular year, make and model. Thank you for asking! 1AAuto.com

[@third763]

Could youplease make a video of how to remove FWD subframe like toyota honda?

[@edwinortiz6392]

Great video. Just like yourr parts. Top notch!

[@1AAuto]

+Edwin Ortiz Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c

[@johnfay6662]

Will this video help me with my 1999 RAV4 rack and pinion too?

[@1AAuto]

+John Fay Great question! Search our video library for more on this vehicle: 1aau.to/m/video-library-c

[@Elinternetsecurity]

absolute perfect explained thank you. xD

[@linhpham-rt4yi]

Nice work

[@muhammadsaeedakhtar5921]

Beginning of video you used the floor jack, how come you are standing under the car.

[@dgoode31c1]

My end links are covered how do I remove the cover without destroying it

[@mikebradford7780]

Nice video, but not near as easy on jack stands.

[@breerosky9204]

Any additional suggestions for getting the steering shaft off the splines of the steering rack? Its hard in the video to see how exactly it comes off. I'm assuming the joint in the steering shaft folds and it should just move upward so its fully off the steering rack shaft. I've pulled at it with a pry bar from the top and hammered at the bottom of it with a pry bar. The video implies it should come off without too much force.

[@1AAuto]

+Breer Osky Thanks for your question! Once the pinch bolt is removed the steering shaft should move off the steering rack with a pry bar. Some penetrating oil may be needed to get the shaft off. Thank you!

[@breerosky9204]

1A Auto Parts Thanks for the prompt reply. Should the pinch bracket be oriented in a particular way or should the joint flex in a particular direction? I have this thing lubed up and loose. Have even jammed a screwdriver in the bracket slot to loosen it up. But can't lift it more than half way off the rack spindle. Next strategy is a longer pry bar for more leverage. Can't think of much else because the thing is obviously loose and free. Just can't get it to lift.

[@breerosky9204]

Thanks! I figured I would go ahead and proceed with the rest of the disconnection steps. After I removed the frame bolts I was able to get enough wiggle in it to pull it off.

[@geraldmartin3625]

Does a 2001 Camry 3.0 v6 feature the same locking nuts on the mounting bolts?

[@1AAuto]

+Gerald Martin Thanks for watching! The part in the video is the same for the 2001 Camry 3.0L, so the process should be pretty much the same! www.1aauto.com/rack-and-pinion-assembly/i/1astg00003?KZbin&CTA+Comment&At7tChYYvY

[@kim7018]

Is the power fluid that is boiling over not going to mess your car paint?

[@1AAuto]

+Kim M The fluid that shoots out will not damage your paint! 1aauto.com

[@dennistaylor9795]

Bravo very good video

[@sonnykhoeblal9473]

is there a difference between RH and Lhand driving ?

[@BPoweredLove]

Yes. On a right-hand car, the steering wheel is on the right side.

[@miguelotrejo2253]

excellent video thks

[@meshal4048]

Great job and explanation...thanks a lot

[@1AAuto]

+Meshal Al-Anbar Thanks for watching. Hope this helps you out. Have a great day! 1aauto.com

[@lawearsmith9851]

What happened if it still stiffness AFTER?

[@ronaldcharles9120]

Can I use that same rack for my Nissan Note 2015 please?

[@1AAuto]

+Ronald Charles We do not have a video for this repair right now, but we'll keep this request in mind for a future video! Your vehicle would not take the same rack as what is used in this video. 1aau.to/m/Shop-1AAuto-c

[@ronaldcharles9120]

@@1AAuto Thank you for the quick response.

[@mizanurrahman3027]

sir help me about car diagonasis by scanner

[@johnfay6662]

Is this similar to a 99 rav4 manual transmission 4WD?

[@1AAuto]

+John Fay We don't have a how-to video for your vehicle right now, but the basic steps in this video should be enough to do this task. Buy this part for your vehicle on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c

[@isthathowyouwanttoplaymerr5708]

What happens when me the dummy watches this video after he messes everything up?

[@sesarman]

Is this the same part as the 98 sienna? Just wondering if tools required will be the same, ty.

[@1AAuto]

+arman sesar Your 98 Sienna would use a different rack and pinion. This particular one would not fit your vehicle.

[@sesarman]

1A Auto Parts but also wondering if the process is the same as well as tools required, thank you.

[@RyanUnded]

Is this the same procedure for a 1998 Toyota RAV4?

[@1AAuto]

+AntiAntihero It may be a diffrent procedure on that vehicle. We currently do not have a video on this particular repair. Thank you for asking 1aauto.com

[@2023_Max]

Those two bolts are tight Going to have to heat them up

[@Torchi0]

It's the same for the Lexus RX300, but the bolts in the rack are 17mm not 19mm.

[@1AAuto]

+Rafael Torchio Thanks for watching. We carry the new rack shown in this video on our website. Here is a link to them www.1aauto.com/rack-and-pinion-assembly/i/1astg00003?KZbin&CTA+Comment&At7tChYYvY