How to Replace Ignition Lock Cylinder 1994-2004 Chevy S-10

Buy Now!
New Ignition Lock Cylinder from 1AAuto.com 1aau.to/ib/1AIMX00157
The ignition lock cylinder provides security by requiring a key to start your vehicle. If there are problems with the lock cylinder, you'll have trouble starting the engine! This video shows you how to install a new ignition lock cylinder on your 1994-2004 Chevy S-10.
• Check here for more videos on the 1994-2004 Chevy S-10 • Chevy S-10 2nd Generat...
This process should be similar on the following vehicles:
1994 Chevrolet S10
1995 Chevrolet S10
1996 Chevrolet S10
1997 Chevrolet S10
1998 Chevrolet S10
1999 Chevrolet S10
2000 Chevrolet S10
2001 Chevrolet S10
2002 Chevrolet S10
2003 Chevrolet S10
2004 Chevrolet S10
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oabq/1AXAA00013
• Trim Tool Set 1aau.to/oxQ/1AXXX00006
• Ratchet 1aau.to/oahu/1AXAA00016
• Socket Driver
• Socket Extensions 1aau.to/oaaX/1AXAA00015
• Pick 1aau.to/opK/1AXAA00037
Subscribe: / @trq
Check out our playlist:
Chevy S-10 2nd Generation 1994-2004: • Chevy S-10 2nd Generat...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

[@toastyghostyofdeath3909]

What do you do to remove the lock cylinder if the key won't turn to the start position? Because thats the reason im replacing it.

[@frankschwartz7405]

Thanks for the explicit tutorial. It would have taken much longer, or been a complete "fail" without it. I never would have found that torx bolt in the top plastic, it fought me hard coming out....now it's an "extra part". The tumbler also put up quite a fight, but after many invectives, I finally prevailed, and then with much celebration. The new one slapped right in, and reassembly was a breeze. Just like new. Thanks again.

[@dewaynedurham9258]

Not to split hairs but you might want to go try and take apart a 95 s10 and see that you should adjust your parameters cause the old dash is way different and has a full circle around the ignition on the top part of the column

[@dizzyassklown4424]

I replaced my ignition lock but i didnt have to take off the dash bezel...

[@sped6954]

I'm down to that part about removing the old lock cylinder. The video says to turn the key while holding the lock in the start position and pushing down in the hole that was created when removing the connector around 3½ minutes into the video. The whole reason for changing it is because the lock wont turn at all. I put the key in, the door open chime sounds, and nothing. It wont turn in either direction.

[@christopherworkman9070]

Nice, detailed video! I love that it shows in-depth how to take the dash and steering column apart. 👍

[@nealbeach4947]

Just finished a 2000 S10 and this video was a great help. No issues at all just took it slow and followed the instructions.

[@TRQ]

+Neal Beach Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-TRQ

[@Tony-dz6yf]

This is a great video i just finished my 2000 Chevy Blazer only issue is that now i have to keep both keys one to access entry and the other to turn on lol better then where i was originally 👍🏽👍🏽👍🏽 thank you for your videos

[@trevorpritchard2985]

Been beating my key with a hammer to unlock the ignition along with a whole lot of jiggling things around lol thanks for the video!!

[@DragonsGarage]

You guys are awesome, thank you!

[@jrbinkard1900]

This is the only video showing how to twist the inside with screw driver to align cylinder Thanks

[@seangorham5626]

I just watched your video and dam a video that actually helps thank u.

[@joesheppard8000]

GREAT video thanks for sharing

[@tjhulsey5837]

Very Good Video... Well Done...

[@donlance9574]

Great video. Would've never thought to have removed that small white connector/pin nor figured out where to push to get it released without breaking it. I did do a small deviation to the procedure in that instead of trying to remove all the electrical connectors ( I have 2wd) from the bezel I just pulled it out/away and Bungy-corded it to the rear view mirror. I did so because I previously had trouble removing the airbag switch which was brittle and broke some tabs so glue was holding it in place and I didn't want to disturb it.

[@G-spotGeorge]

This is how you do it on the pre facelift models 1. Remove plastics on top and bottom behind steering wheel 2. Turn key all the way then push the tap down while pushing out on the old cylinder 3. Once you get the cylinder out a little ways pry on it with a flathead or something while removing whatever you used to push the tap down with in step 2. 4. Once you have the old one out reinstall top and bottom plastics 5. Insert new cylinder and turn key back to off position and you're done

[@timothyhines7697]

I appreciate it real good video

[@aaron552]

Thank you so much for this detailed video, I was able to change out my ignition in 30 minutes, and I am not car savvy lol. You saved me money by doing it myself much appreciated!

[@danakibby627]

Great video

[@kennyboy6284]

Thanks for the help

[@robinfreshour7388]

What if you don't have keys

[@wendyream2360]

Great info

[@williamrice2976]

U should do one with no keys problem

[@JimmyEatWorm]

Hello bought part, do I have to reprogram after installing?

[@Artemis03Lian]

what is the tool for the inverted torx bolt?

[@everywares6010]

How can I remove the key switch if I can’t remove the top cover... my top cover is actually wrapped around the key switch. I can’t do it in the order you did. I have to pull out my key switch first to remove the top cover.

[@young1macdaddy]

Straight to the point

[@TRQ]

+young1macdaddy Thanks for watching our video! 1aau.to/m/Shop-TRQ

[@fivenightsatgoldenfreddys4912]

Cam you use the stock key if you replace the cylinder

[@cyranoburleson4240]

Thanks man

[@aaroncalhoun9713]

I changed mine and the lock doesn't retract brack after cranking it, I have to pull it back slightly so it isn't in full cranking position... any suggestions?

[@pariahsogodly]

Hey, currently trying to do this repair on my 2000 zr2 since some tweekers cracked the ignition when they stole it… only issue is that my old cylinder is locked into place, how should/could I go about removing that without damaging anything else?

[@williamrice2976]

That's the same problem I have

[@jaredadams731]

Some probably here. Except the got the cylinder loose and know it’s hanging down from the wires and I’m not sure where to go from here

[@davidjoeseph2646]

Have to remove the wheel and a bunch of stuff

[@cinos78579]

What is the small harness at the 4 minute mark? In my vehicle it is not there and the wires are on the other side of the column cut and taped together.

[@fredromo5891]

Any know what size the inverted screw size is?

[@tylerseitz6337]

What about the 1994 S10? Same equipment. Different interior. My steering column is one piece. Im pretty sure i have to remove the steering wheel to get to the source. Any tips or tricks?

[@garyhawthorne1678]

what size is that tork head

[@alexmajor6579]

My key won't turn at all so how do I replace this without placing the key in the on position

[@calvinballew5411]

Good question. I have the same problem

[@alexmajor6579]

@@calvinballew5411 hey dude don't know if you've found a fix yet. I ended up replacing the entire ignition lock assembly housing on mine. I followed a video on KZbin called " 02 chevy avalanche ignition case replacement procedure - passlock fix" I bought the housing and a new tumbler with keys as well as a steering wheel puller and a plate and a steering collumn compression tool to remove the lock ring. I used the part number for the adapter plate is J-42137 K-M USA just Google that and it will come up. Any steering column compression tool should work with it. As well as any steering wheel puller with spots for opposing bolts

[@alexmajor6579]

@@calvinballew5411 you have to remove the airbag and steering wheel as well as the shrowd around the drive shaft that video had every thing I needed once I had the tools and parts. Hope that helps you or whoever else sees this

[@patrickcahilljr8384]

YOU HAVE TO DISCONNECT THE BATTERY AND TURN THE KEY ALL THE WAY FORWARD ( TO THE CRANK OVER POSITION) AND PUSH IN THE WHOLE FOR IT TO COME OUT...IT EILL NOT COME OUT ANY OTHER WAY

[@SIMPLYME-bu1me]

What size torx driver is used under the steering column to take those 2 mounting bolts out? Thanks

[@SIMPLYME-bu1me]

I am going to answer my own question. That takes a T25 driver.

[@MadMax-yq9ix]

Might have this problem with my 2000 chevy blazer 4 wheel drive I'll update if it fixes it

[@josecortes6385]

What i do my truck was stolen and I can’t take off the switch any recommendations??

[@antlil4545]

what do you do if your ignition won't lock in place to put the new key cylinder in. please help

[@gregtaylor8414]

What if I put the new cylinder in and didn't tighten the snug and screw and it turned backwards passed auxiliary and stuck

[@immapopcha]

I have a 2002 sonoma and lost my keys. Any clue what choice I have if any? I need help lol

[@sprayarm]

Do you not have to disable the airbag?

[@anthonysolomon9891]

Thank u

[@erniesanchez4860]

Is there seniors in there that would cause gauges and blinkers not to work? Reason I think it is because my gauges aren't working and my blinkers aren't working. Beeping sound like key is in the ignition but not turned on and battery light. Battery and fuses are good

[@TRQ]

+Ernie Sanchez We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

[@craigscott3225]

I have a 1996 GMC Jimmy / Chevrolet Blazer. This video shows trim that is not like mine. It is not like the neighbors blazer or pickup either.

[@luisparamo9402]

How can I removing the cylinder lock if my key will not turn too be able too remove cylinder

[@pjwoo276]

same prob. I guess no one knows. I have asked same question 6 different places. no answers

[@andresespinoza9961]

@@pjwoo276 gonna have to call a locksmith to remove it for you.

[@danielholguin2740]

Is this the same with the Manuel’s?

[@TRQ]

+Daniel Holguin This procedure might be different for your application. We do not currently have a how-to video for this particular year, make and model. Thank you for asking! 1aau.to/m/Shop-TRQ

[@timthemechanix]

1996 is different. the cover does not split around the key. the top cover goes down and around the key lock.

[@lauraluna2739]

I changed the cylinder ignition switch on my 2000 Chevy Astro and it still won’t start. The panel won’t register.

[@big6pun07]

Any luck yet

[@pjwoo276]

Can someone refer me to a video showing how to replace door lock cylinders on 2003 chevy S-10 ?

[@ladonnagauchat6428]

Google

[@ronsmykowski7850]

Why can't you drill a hole about where that pin is and stick a coat hanger in and release it and not have to go through all that extra work.

[@HansZuerner918]

how to reset ignition switch

[@daltonwood8294]

What if I can’t turn my key at all

[@user-nh1gt4ou6i]

94 to 97 total different!

[@anthonykeeler8814]

94 GMC Sonoma is way different than that

[@billyhogan1863]

So what if you don't have any key's and still need to replace the switch????? I guess just replace the column

[@gustavomarin7680]

What if my steering wheel is locked and can’t get it to loosen so that I can turn my key over ?

[@ladonnagauchat6428]

Jiggle the wheel while trying to turn the key

[@yousuckdicks1]

did you get it figured out? I have the same issue after a break-in

[@joemorriosn3761]

what if you don't have a key ?

[@davidboen9649]

Some one trip to steel the truck broke it all up

[@jamesturner3067]

I don’t have a key tho

[@kelleykayschmidt6902]

Education

[@toxsickdog]

how do you remove the damned lock if your key is gone? I lost mine. should I get out the Sawzall ?

[@adrtru]

shove a skrewdriver in there

[@charlesfischer450]

I destroyed my tumbler trying to get it out. Then I destroyed the housing trying to get that off..... like I'm not mechanically retarded, but Jesus fuck every vehicle I've ever owned never ends up being easy peasy like this.

[@carlosbenavides1566]

Me neither didn't have to remove half of that

[@thatredchicken7580]

So my question is what if you've lost the key and want to replace the cylinder

[@Kelly-kr2wr]

Ive the same problem

[@mikemercurio6025]

I’m a locksmith and we know how to do it but it involves picking the ignition

[@ronaldcotner4710]

The cylinder will not come out

[@keenanboone]

U didn't afto program the key to it

[@user-zb2nf7oq5q]

This will not work wrong steering column

[@Kelly-kr2wr]

Yeah how about with no key

[@jgonzalez8250]

Friends?! Calm down Ross.

[@robinfreshour7388]

No keys

[@user-zb2nf7oq5q]

I asked without the key