NOTE: if you do this procedure and you can’t get your new ignition to pop right in you have to take a big screwdriver put it in the hole and rotate the ignition square all the way back, after I did this my new ignition slid right and and worked great!! Thanks so much, Greg
@flyin2low2c5 жыл бұрын
Thanks for that info !!
@edwardeliyahhamner43403 жыл бұрын
Thanks because that's excatly what I was experiencing.
@jaybrown59852 жыл бұрын
Someone try stealing my truck my key won’t turn at all
@ianconley6673Ай бұрын
In the housing itself or with the new ignition 75%in? I'm doing it rn and feel like I'm going to break something in the housing 😂
@sadiegirlwolfАй бұрын
With no ignition at all in housing stick screwdriver in and rotate back hole that accepts the new ignition
@SonnyThomasShow1 Жыл бұрын
I appreciate you also showing how to replace everything step by step as you put it all back together. Lots of times people just say "reverse procedure to finish it." You actually did it. 👍🏻
@johndefeo264 жыл бұрын
Daninator! This video saved my butt on a cross country trip. Did this as a last ditch effort to see if I could get my truck to start and it did the trick, safely back on the road an hour later! Hats off to you my friend!!
@TheDaninator4 жыл бұрын
Glad the vid helped you out!
@lucasarielbarrera73134 жыл бұрын
You need to go until start position, but put in reverse and after that, turn the key until start position and push the retainer and pull it out. I'm a professional locksmith.
@shawnglover57683 жыл бұрын
THANK U!!!!!!!!!!! Im outside sweating my ass off trying to pull the cylinder out and it did not come out til I did what u said
@wrucker10005 жыл бұрын
The video was great. I have a 1999 Silverado and my ignition lock cylinder needed replacing. I was nervous to tackle it at first, but with the video you created made it a breeze, once I purchase the right tools. The only thing that I would add is: When inserting the new cylinder, you may need to use a big flathead screwdriver to insert into the core space to turn the switch just a little to line it up to receive the new ignition. cylinder. I had to figure that out to get the cylinder to seat properly. When I put everything back together, it works like new! Thanks.... Oh yeah I had the dealer to set the cylinder to match my existing keys.
@anthonyg93892 жыл бұрын
How much did it cost for the dealer to set the cylinder to match the existing keys?
@chrisg13642 жыл бұрын
@@anthonyg9389 did u ever find out??
@anthonyg93892 жыл бұрын
@@chrisg1364 no, I just bought aftermarket ignition lock cylinder from amazon
@carlospaz209 Жыл бұрын
Thank you William, your comment saved my ass tonight. Small turn from 10 o'clock back to 12
@rememberussliberty18225 жыл бұрын
I didnt want to give up my key and have to use a diffrent one for doors and ignition. Took out the lock cylinder like he did, got a very fine file. In my case it wasnt those two little pins causing my problem it was a sharp edge that had developed and it was catching. Rounded a few edges and bingo!! It is very easy to start these trucks without a key i discovered..
@brandenbeaverbone55643 жыл бұрын
I like your pepe pfp good sir I did not read your comment however, that is all.
@webrad982 жыл бұрын
Thank You! I was stuck in the driveway blocking other cars and after getting the covers off was able to press on the lock rod enough to park the truck to the side, I took the car and got the parts and now it works.
@rextorgerson8004 Жыл бұрын
Thanks for posting this video only difference was mine was a 2006 Z71 made my repair easy 👍👍 Just a couple different steps on mine. It didn’t have bolts holding column plastic together so all I had to do was use a small flat screw driver to start separation of plastics. Carefully Oh also I had to hold key all the way forward in start position to be able to push in release button to pull out old lock cylinder. Thanks again 👍
@JeffL12344 жыл бұрын
Thanks, easy to follow instructions. Done in 30 minutes. We did have to use flathead screwdriver to line up inside parts to insert new ignition.
@johnorosz74773 жыл бұрын
NOTE: if you do this procedure and you can’t get your new ignition to pop right in you have to take a big screwdriver put it in the hole and rotate the ignition square all the way back, after I did this my new ignition slid right and and worked great!! Thanks so much, Greg
@webrad982 жыл бұрын
Same Here. Glad I had a flashlight to see why things weren't lining up.
@JBoysbarbershop4 жыл бұрын
One thing I'd like to add that happened to me while I was replacing the switch was ,When I took the switch out and went to put the new one in. Inside the ignition itself, moved in there. so the new key switch wouldn't go back in until I put a flathead in there and turned it back the match the key cylinder ,Then it fell right in . Thanks for posting
@JBoysbarbershop4 жыл бұрын
P.S. There was no 4m bolt in there. just used a finish nail to remove the switch.
@chilarue62794 жыл бұрын
You save my life!! You need a reward lol I couldn’t figure out why it wouldn’t fit!! Thank you so much
@minnesota70103 жыл бұрын
Did mine for 12.99. Thanks. If you lived close id buy you few beers... Locksmith wanted 300.00
@salvadorbernal9392 Жыл бұрын
Finally a straight to the point video nice work you made it look easy thank you
@williamrush8370 Жыл бұрын
VERY GOOD INFO DIRECTION EXPLANATION AND PIC OF ALL POINTS NEED TO FIX THIS PROBLEM, THIS MAKES YOU MY FRIEND INDEED! THANK YOU THUMBS UP TO YOU. KEEP UP THE GOOD WORK!
@gw42037 жыл бұрын
Wow, thanks for posting this! You saved me another almost sleepless night and an expensive tow. Not to mention the mechanics charge.
@AgnesM6 жыл бұрын
G W you did it all yourself and it worked out?
@tommurphy2206 жыл бұрын
Bless you, my new friend. I watched another video to diagnose and understand that this was something I could do. But I couldn't get the top housing off the steering column of our 2003 Chevy S10 until I saw you identify the problem bolt, AND suggest using a 4 mm socket wrench to get it off. (Watched 3 other videos before yours, and they suggested removing the steering wheel and airbag to get at it. No!) You saved me tons of time and money!
@TheDaninator6 жыл бұрын
Good deal! Thanks
@gagewade29463 жыл бұрын
Someone broke into my truck and snapped that part off so thanx for the video now i can replace it myself thanx man
@urbanbluecollar78133 жыл бұрын
Me too
@gagewade29463 жыл бұрын
@@urbanbluecollar7813 sorry to hear that i got a new part put it in and got theft insurance👌
@thycarguru42523 жыл бұрын
@@gagewade2946 did it work
@gagewade29463 жыл бұрын
@@thycarguru4252 like a glove i appreciate this guys video
@deejay48395 жыл бұрын
Thanks just replaced my ignition switch appreciate the video saved me $150.
@TheDaninator5 жыл бұрын
Awesome!
@CreekyGuy7 жыл бұрын
Totally pro! Excellent tutorial. Even the volume gain was good (often lacking elsewhere).
@iwinzeazy8 жыл бұрын
Be sure and try a factory key first. I had called the locksmith and told them I was gonna try key first. I had given my wife a key to my truck when I bought it 9 years ago and lucky for me she still had it and boom! It started right up!!!! Basics first :)
@nuttinbetter2do4512 жыл бұрын
Thank you very much for posting this video my truck recently got broke into and they ruined my Ignition switch so I'm going to have to change it out. this video helps a lot thank you.
@stefansmyle9369 Жыл бұрын
This video was very helpful for me because I learned how to pull the cylinder out mine was broke on the on position if your key won’t turn you need to push both pins in by sliding something that will lift them out and then it will turn to the start position I need to crank it all the way over to push in the pin you will see that if you buy a new lock like I did this video is very helpful thank you A+
@mattcox33734 жыл бұрын
Thanks for this video. You saved me a lot of money and stress. My key wouldn’t turn, but a flathead and hammer freed it up pretty easily.
@mattcox33732 жыл бұрын
@The Masked Hoodie luckily no. I was just careful
@mattcox33732 жыл бұрын
@The Masked Hoodie my ignition switch wouldn’t even turn for me to be able to get it out to change it. So I had to stick the flathead in where the key goes and hit it with a hammer until it broke lose. I was changing the switch out anyway so I didn’t care if I messed that one up
@DrSexiiful2 жыл бұрын
@The Masked Hoodie you could stick a flat into the ignition while using vice grips to turn the ignition itself have to remove the plastic ears first though make sure u clamp onto metal
@tiffiny692 жыл бұрын
Bro!!! Thank you so much for this video. I'm having this exact problem, and no man in my life to help solve it. Lol I should be able to fix this no problem! You are a life saver!!! Bless you!!! 🙌
@captprice1b-064 ай бұрын
Thank you sooooo sooooooo much, this helped me and my grandpa ALOOOOOTTTT 5 Stars! ⭐️⭐️⭐️⭐️⭐️
@Ray-hg3ie7 жыл бұрын
Thanks!!!!! I spent all afternoon trying to get the top plastic cover off. Never would have found that 4mm screw without your help. Probably would have had to rip that piece out before I found that damn screw.
@TheDaninator7 жыл бұрын
Haha. I'm sure that happens alot!
@brucejamison78092 жыл бұрын
It is not actually a 4 mm screw. There are star sockets that are the correct tool for this.
@anthonytorres56487 жыл бұрын
Thanks for the video bro now my 02 escalade has a functioning ignition switch again
@TheDaninator7 жыл бұрын
Awesome!
@Janzer_2 жыл бұрын
this is great. an option is to buy an "un-coded" ignition lock cylinder and code that (there's videos on how to do that) so you won't have to use two keys.
@trueopsimath8 жыл бұрын
Good video. I've got the same problem, and now I'm confident I can fix this myself. I'll give it a try this week.
@TheDaninator8 жыл бұрын
Happy repairs!
@trueopsimath8 жыл бұрын
I decided to tear into it this week. Apparently the previous owner had struggled with the problem. To begin with, getting the covers off the steering column was a snap because he didn't bother to put the retaining screws back in. With only a moment's struggle, I was able to extract the old cylinder, to discover that it had been liberally slathered with grease. That would explain why everything worked fine when I bought the truck, but started going downhill soon after. I popped in the new cylinder without any issues and replaced the covers. The whole process took only a few minutes. Thanks again for posting your video!
@lovetofly322 жыл бұрын
Just had mine all appart because mine was stuck in the crank position. That little gold plate under his tool on the tumbler at 3:57 was popped out. The corners of it are stamped into the casting of the aluminum tumbler. It looks like it holds the springs in the lock. I tapped the spots back down in the corners to stamp it back in place and now it works again. It's very soft aluminum. Mine does do the same thing this guys did and I also thought it was the pins catching on those ramps but I can hold them both IN and it still catches. I think its the little black block on the side of the tumbler that sticks out just a fuzz when the key is out but then goes in when the key is in. I believe it's what prevents you from turning the tumbler without the key in. I don't think it's coming out of the notch where it rides in the female part where it goes into the column. It seems a little cockeyed. I believe that's what catches and not the pins.
@johnnybrents913 жыл бұрын
The ignition not turning has absolutely nothing to do with the spring pin as you referred to. It has to do with worn wafers in the lock that are not matching up with your key. All you would have to do is go to a locksmith and get him or her to replace the wafers and your lock is good as new. And you wouldn’t have two keys. You could’ve had the new lock rekeyed to match your old key so everything is on one key but then again you spent money on a new lock that was not necessary. That groove as you called it you said wore out does not happen. Always a good idea to ask a pro. You save money and you don’t misinform people with this nonsense.
@goldenstatepicker Жыл бұрын
Johnny is Mr. Know-it-all. Those guys are the ones you want to avoid taking your car too. @@jaysmokey
@CSpad Жыл бұрын
Well Johnny know nothing. A locksmith is gonna cost you between $100- $180 to make you a transponder/chip key. While for $100, I got a new lock cylinder& 2 new transponder keys that I was able to program myself.
@Gumby40911 ай бұрын
You’re the bastards people need to stay away from . Why the Fuck ramble on about this . Stay dumb
@yaboi56863 ай бұрын
@@CSpadunless you got a remote I’m sure you’re not worried about your ignition key not matching with the door anymore, better hope that battery doesn’t run out
@surftoryblue8 жыл бұрын
Thank u! I just fix a my Girlfriends 96 Chevy 1500 Silverado Ignition Cylinder , it took me a minute jiggling it back and forth but slid out, thanks for the pointer !
@TheDaninator8 жыл бұрын
Awesome! Glad my video helped.
@andrewstartek58462 жыл бұрын
Looks like you were able to turn the key lot of help
@KennethLittle-u3r11 ай бұрын
Excellent video about 30 minutes and I was up and running
@encoencomen83612 жыл бұрын
Great video. Some amateur Jackass broke into my truck this morning and boogered up my ignition switch. Didn't get the truck. If only I was up I could of put 6 slugs through his partner's windshield.
@martytruelove50264 жыл бұрын
THANKS Buddy,nice to know the tools required going into something
@1320Jason2 жыл бұрын
Agreed
@whistlinframer68124 жыл бұрын
Where are you man? This helped me so much that I want to buy you a case of beer
@eshacooper87412 жыл бұрын
Thanks for the thorough explanation. Top cover was giving me a time.
@spamwagon3 жыл бұрын
So, my ignition switch would NOT move, NO way to rotate to the start position to remove/replace. I pried the plastic off the switch and located the keyway that pops up to lock the cylinder. The springs can fail and the keyway does not disengage from the housing. It's basically right where the arrow on the plastic is. I used a die grinder to cut off the shoulder of the cylinder right where that keyway is (careful not to damage anything else). Put the key all the way into the switch. Then, I took a baby (very small) flathead screwdriver and pushed the keyway down (back into the cylinder slot), tapping the screwdriver in as far as I could. Had to help turn the cylinder with some channel locks, but I got the cylinder to rotate clockwise to that start position and I could then pull it out. New one popped right in.
@ireuel3574 жыл бұрын
Key won't turn...except that yours does, so it's easy to switch out the cylinder. Not helpful.
@boggy60602 жыл бұрын
È
@romangarza6037 Жыл бұрын
79 dodge brougham rv installed new ignition
@geraldturner8377 Жыл бұрын
Same issue
@davidhoneycutt1965 Жыл бұрын
Take the key out and smack it with a screw driver handle and keep working it. She'll give
@jasonboyko Жыл бұрын
@@davidhoneycutt1965smack her around a bit, and she'll comply, lol
@ramirez234568 жыл бұрын
gracias amigo me ayudo mucho tu video llevo 2 anos con ese problema porfin pude arreglarlo thanks
@brainyak7408 Жыл бұрын
For $28 + around $12 shipping, you can get one with a GM stamped key from Classic Industries. That GM stamp is important to some folks.
@robertrutherford94383 жыл бұрын
THANK YOU FOR THIS VIDEO!!!!!!!! This is the easiest serious problem I've ever fixed. Life saver for real!
@5150santana6 жыл бұрын
this video saved me alot of money by doing it myself thanks
@ksduathlete2 жыл бұрын
Just changed mine and your video was awesome. It still doesn't want to turn from the off position but once its out of off position its like butter. Should i have greased the new one?
@andyandycapt79472 жыл бұрын
Best I’ve seen yet
@nolancushing28112 жыл бұрын
Thanks so much for the video! It totally came in handy. I didn't want to pay an arm and a leg to fix it. Thanks
@eugeneirby2286 жыл бұрын
ALL I CAN SAY IS THANKS THAMKS THANKS MADE IT SO EASY, DAM GOOD VIDEO!!!!!
@1320Jason2 жыл бұрын
I gotta do this to dad’s truck. Thanks for the video!!!!
@drolnady6 жыл бұрын
Replacing the rubber shift lever 'boot' while in there is also a good idea. And, if you have tow/haul switch, the orange wire is prone to breaking because factory stretched too tight.
@ConnieFoster12 жыл бұрын
Well, great video. I was able to get thru all the steps until the part where the key has to be turned on in order to release the lock cylinder. But that's my problem! The key won't turn. Very frustrating
@angelrosario60522 жыл бұрын
Did you ever figure it out?
@bghankhernandez7 жыл бұрын
Perfect instructions. But when I pulled ignition out,inside tumbler turned so new ignition wouldnt go in...aaahh thought for sec then i used a 5/16 closed end..to turn a little to line up,went right in. Thanks.
@johnorosz74773 жыл бұрын
Special Note: if you do this procedure and you can’t get your new ignition to pop right in you have to take a big screwdriver put it in the hole and rotate the ignition square all the way back, after I did this my new ignition slid right and and worked great!! Thanks so much, Greg
@pedjastanich43476 жыл бұрын
Thank you for sharing. You are a gentleman and a scholar.
@TheDaninator6 жыл бұрын
Why, thank you kind sir.
@cemetery765 жыл бұрын
don't know if mine froze up from moisture got in it,or it's jacked up. I sprayed PB Blaster in the key hole got it to turn,it's not gonna hurt it. you can use WD40 to it should work, hope this helps.
@joaquincarranza75692 жыл бұрын
Thanks alot it was so helpful thanks you very much appreciate
@midos67674 жыл бұрын
My 1995 Chevy S10 has the same problem with the ignition switch not turning sometimes. I just jiggle it a little and it works. But I like to keep it that way so that my girlfriend can't drive it. I don't want anyone else driving my old truck but me.
@texantracey Жыл бұрын
Excellent video!
@NickMattia448 ай бұрын
Mine won’t even turn to the second position at ALL. So I can’t remove the cylinder. Any advice?
@jasontodd69304 ай бұрын
It will turn you just gotta play with it. I have to fiddle with mine for 30 minutes sometimes before it finally turns. If all else fails you can tap it out with a screwdriver and turn it since you’re putting a new one in it anyways.
@bobthomas1433 жыл бұрын
How do you get the cylinder out if the key won't turn to the on position???
@bobthomas1433 жыл бұрын
Got it out by getting a thin metal strip and pushing the tab in. After that 15 minutes , new one installed and job complete.
@minnesota70103 жыл бұрын
@@bobthomas143 Thanks Bob did mine today I got a thin piece of metal like you said and it work thankkkkkkk youuuuuuuu! I want a by you a case of beer if you drink... Peace out....
@Beliefacy2 жыл бұрын
@@bobthomas143 please can you be more descriptive? Thin metal for what piece? Wtf
@johnorosz74773 жыл бұрын
1996 Chev. C-1500: This works great but the fact is you need the ignition to go forward in order to even remove the core/barrel. I cannot turn the key at all. So it refuses to let me remove the barrel cylinder and replace it. Both keys refuse to work on this ignition. May need to call a specialist.
@wallace21572 жыл бұрын
im in same situation key broke off and 2nd set was a gmc set from csnada?
@wallace21572 жыл бұрын
just got it towed bit took column apart can get out of park still wont turn ignition though
@DirtRoadDude5 жыл бұрын
great help! thank you! just did mine and found out have to turn the key to the "start" position to remove the cylinder. so unhooking the battery is the way to go.
@angelrosario60522 жыл бұрын
What if you can’t move the key to start
@ultraman502 жыл бұрын
Great video. Thanks. I R/R one on my 1995 f150 long ago and it was so much easier. Didn’t have to take anything apart. But still looks easy enough. Thx agsin !
@ericvaughn28752 жыл бұрын
Saved me 100. Thanks
@YuoseB27 күн бұрын
very big thank you so much😀
@jonwatts19182 жыл бұрын
Dude you saved my butt today.
@Master_Yoda19904 жыл бұрын
That works if you can turn the key, but I can’t turn my key as state in the title, so this video is more or less useless for me others expecting to see you fix a cylinder lock that won’t turn.
@sleepytime46492 жыл бұрын
I could turn mine with a screwdriver, it sucks but it’s better than nothing
@Master_Yoda19902 жыл бұрын
@@sleepytime4649 I ended up tapping the key with a hammer while turning it to unjam the cylinder lock.
@wallace21572 жыл бұрын
at if your key broke off in thebignition its on a slant so very hard to get out
@Master_Yoda19902 жыл бұрын
@@wallace2157 try a key extractor, lock picking sets usually has one.
@wallace21572 жыл бұрын
I gave in bought new ignition
@poolnoodle53113 жыл бұрын
Awesome video. My 1999 also have the GM Jiggle. You didn't have to program your new ignition to the pickup?
@jamarlewis30507 жыл бұрын
Hey man just wanted to say thank you for your guidance ...
@TheDaninator7 жыл бұрын
Glad it helped you out
@DavidSmith-by6gr Жыл бұрын
That doesn’t tell anyone shit if their key will not turn. Great job dingus
@thewhittierlocksmith1217 ай бұрын
kzbin.info/www/bejne/eImsc4yMa7yZrrM
@xinoss50863 жыл бұрын
this is so helpful! my granddad left me a 2000 chevy Silverado 1500 and he ended up loosing the key so I had to buy a replacement switch
@discmotoslots5 жыл бұрын
perfect! just what I needed for my sticky key! thanks
@lilgrover694 жыл бұрын
That's the AC delco that costs 258 bucks right?
@desigualteam56682 жыл бұрын
Tks , it helped a lot
@tupito458 жыл бұрын
thank you it worked good for me and I didn't have the old key so I just used my new key to turn it as I put pressure with bar and boom...thank again
@edpotts91685 жыл бұрын
very well done, straight and to the point..kudos !!
@thumbelina27256 жыл бұрын
Thank u...been without my vehicle for 8 months...2000 Suburban 1500..towing and repair would have cost $500 at the local mechanics. Guess they sure know how to rip people off if u r at their mercy. Sad
@abrahamaragon33653 жыл бұрын
Thank you very much for the information
@stephanlapointe67716 жыл бұрын
Thanks for the video! When I put my new cylinder in it fit but it won't turn all the way back to off. Does this mean something else is wrong?
@truthaboveagenda8 жыл бұрын
. Well stated, well done video. -Joseph
@mikemckenzie17963 жыл бұрын
Saved me a pretty penny thanks!!!
@bassaddicts57444 жыл бұрын
Will this work if you don’t have the factory key. I lost mine and the locks have previously been changed. Thinking about doing this instead of having it towed to the dealer ship for someone to make me a new one
@MrPaul53253 жыл бұрын
AWESOME Thanks very GOOD
@temirovich6 жыл бұрын
Its not two small pins you talking about in the video,its your key wore out or inside cylinder,I did have the same problem and replaced with new cylinder,if you look at your old cylinder and when you put key in,small plate on the side supposed to slide inside to make a free turn
@TheDaninator6 жыл бұрын
Cool. Thank you for the info!
@minnesota70103 жыл бұрын
Einstein
@24chikillin7 жыл бұрын
Wow that was fast thanks for the help
@jorgefernandez65553 жыл бұрын
I can say is thank you so much for that video
@dakotariddle57152 жыл бұрын
Very informative
@roadstar4998 жыл бұрын
wow..I have same exact problem in my 2001 Silverado and even worse in a 2005 gmc 1500...I watched another video and he removed wheel and looked like a major pain in the sack..this seems very doable. .but I will spray some lube on that area first to see if that helps...thanks for the great job!
@TheDaninator8 жыл бұрын
Yes, very doable. Easy fix. Oil may do some good.
@roadstar4998 жыл бұрын
+The Daninator I used liquid wrench silicone spray lube and works way better...thanks
@TheSchyllerwade Жыл бұрын
Hi, someone tried to steal my truck last night and they messed with the cylinder-I can’t even get my key in there now. Can I still replace it using this method?
@dftsp33ddemon143 жыл бұрын
I'm having trouble because the person before me that sold me the truck had all this in a mess and things tapped in place using electrical tap but after removing the tap the truck won't start and I noticed that those wires ain't there so they were either not on my truck or they were removed and if that's the case and if it is part of the security system in anyway I'm wondering if that's why it won't start anymore
@kevinschmidt23018 жыл бұрын
I did what another video showed drilled a small hole in the cover and came out fine ,but it was not the problem it is the ignition switch,on to find those videos now.
@lowpricekeys66294 жыл бұрын
Thank you for sharing this detailed amazing video great job 👍⭐⭐⭐⭐⭐
@vozdetrueno52393 жыл бұрын
Thank you so very much! This was easier than. 1 2 3 Uno, Dos , Tres 👍
@seeyeshua7 жыл бұрын
thanks buddy. ..u made it look easy & it was thx again
@TheDaninator7 жыл бұрын
Awesome!
@Val_Halla7775 жыл бұрын
Nice job. Thanks for this..exactly what I was looking for. I think I have related issue..in my situation it takes several random turns before the key actually engages the starter/ignition..do you think this is also some type of wear on the cylinder ? Thanks again - great vid👍
@TheDaninator5 жыл бұрын
Val Halla it’s possible. But I would guess that may have something to do with your ignition switch...but that’s just a guess.
@Val_Halla7775 жыл бұрын
The Daninator ok..Thanks for the reply. Really appreciated. Cheers
@everybodystaycalm50902 жыл бұрын
I just came across this video looking to fix my truck someone try to steal it the other day and broke the aluminum part where the blue mark is and the ignition cylinder is there a way to replace the whole thing? Any help would be appreciated! Thanks
@sage36015 жыл бұрын
Okay we have a 05 Tahoe that does the same thing but it won’t start right away Ana there’s a clicking noise on the passenger side of the engine? Been wanting to know what it was and if this could also be related to it not starting properly.
@TheDaninator5 жыл бұрын
Sage Listo the clicking noise could be a problem with the starter.
@MILESHERLONG-me6sk3 ай бұрын
The key was worn. The ignition lock cylinder did not need to be replaced. You cannot trace the old key, you must cut a new one to the original factory depths ( usually done at dealer or with a locksmith). I worked at a GM dealership for over 30 years.
@jorgefonseca92257 жыл бұрын
nice vedeo mate good help i need replace on my suburban 95 regards from norway
@TheDaninator7 жыл бұрын
jorge fonseca cool! Glad my vid helped you out way over there! Happy repairs!
@jorgefonseca92257 жыл бұрын
i take some time but i fix as well great help i need help for electric problem!! dam speedometer not working after a modification (i remove a automatic trans. tu full manual trans. 5speed NV4500) now is not working i don"t understend why!! all cables and conectores is in right place and no damage i"m so sad i try undred thinks and still not working i need find some fella understend a GM electric shematic"s anyway thanks mate i apreciate if someone can help me
@BM-xc9sq8 жыл бұрын
I had a problem with not being able to turn ignition completely off to remove key. Replaced the ignition switch and lock mechinisim. worked fine for a short time, now it's doing it again. "97 S-10 pickup
@meatyman9258 жыл бұрын
Thanks for the video worked for me I have 2002 chevy Silverado
@davidcollins69567 жыл бұрын
Jonath an
@Lore-wv5mt6 жыл бұрын
Jonathan did u haded to program it???
@brendancheung8 жыл бұрын
Great video - I did the whole swap over and installed the new cylinder fine, but the car won't start with the new cylinder. Does the Cylinder need to be recoded for it to work properly. I am in a 2007 Avalanche and the starter and switch should be fine. The truck starts fine just the key gets stuck often and I have to wiggle it to get it started. Any suggestions?
@johnorosz74773 жыл бұрын
The electrical on the other side of your ignition sounds like it could have a short but you would need to meter it out as well as test the current on the entire ignition system.