How To Replace Laundry Sink Faucet

We wanted to replace the laundry sink faucet because the operating knobs were harder to twist open and close to operate.
Here's the link of to the faucet:
www.homedepot....
Thank you for watching and appreciate the support!
-Sam

[@stevensrodas2695]

Great help with video

[@garyfriedman7953]

Thank you! I was able to change out the faucet thanks to your help. Saved me from paying a plumber.

[@TheAsisami]

Looks easy peasy…now watch me eff it up….😂😂😂

[@johndesaavedra1040]

What about sealant around the stems to replace those nice rubber washers the original came with? This will slowly drip each time water splashes against the base. Also the threads are not the point of seal so the teflon tape is for looks only. The seal is from the end washers on the supply lines.

[@DaleGuiney]

Great finger tight and finger loosening job, what about old one being wrench tight. Any tricks to that?

[@Tendertroll1]

Nice faucet

[@carlosprovyrivera8522]

Thx for sharing this. It would seem to me that you just hand tightened all the connections. Correct?

[@thisandthat5571]

you can use faucet wrench.. something like this: www.amazon.com/dp/B09T5XXCFR/ref=sspa_dk_detail_2?psc=1&pd_rd_i=B09T5XXCFR&pd_rd_w=0d8ou&content-id=amzn1.sym.386c274b-4bfe-4421-9052-a1a56db557ab&pf_rd_p=386c274b-4bfe-4421-9052-a1a56db557ab&pf_rd_r=MH2V6ZJ5JZW0YRJ1ANAM&pd_rd_wg=2QZGd&pd_rd_r=01451eaa-246c-4ec7-b60a-40f9794deab2&s=hi&sp_csd=d2lkZ2V0TmFtZT1zcF9kZXRhaWxfdGhlbWF0aWM&smid=A1EVUZ0YF1PQVS

[@cobrabtc]

I had more difficulty removing the laundry room’s 17 year old faucet … so corroded and rusted.

[@LetsReflectOnIt]

Thanks for sharing. Just purchased to install. Question if I may- is the tape needed or you just wanted to use?

[@thisandthat5571]

Thanks.. use the teflon tape. It's so inexpensive and gives you better water seal to the hose: www.homedepot.com/p/1-2-in-x-260-in-PTFE-Thread-Seal-Tape-PTT-5/204286187?g_store=&source=shoppingads&locale=en-US&&mtc=Shopping-B-F_D25H-G-D25H-025_012_PNEUM_FAST-NA-NA-Feed-SMART-NA-NA-PneumaticFasteners_Smart&cm_mmc=Shopping-B-F_D25H-G-D25H-025_012_PNEUM_FAST-NA-NA-Feed-SMART-NA-NA-PneumaticFasteners_Smart-71700000080178040-58700006732570910-92700066574864457&gclid=Cj0KCQiAkZKNBhDiARIsAPsk0WhmzYNS1t56FId7KCM2oH1CQXb2DRHm9R-DzUUkszJ04xtXlTujEgMaAi4iEALw_wcB&gclsrc=aw.ds

[@LetsReflectOnIt]

This and That Will do. Thank you!

[@AgentOffice]

@@LetsReflectOnIt no don't use Teflon when there's a gasket

[@Finny-kx3fk]

Thank you!

[@rayebner6457]

Tape not needed on the threads.

[@antwoinescars266]

What tool did you use on the water line? I’m having a hard time fitting anything back there

[@thisandthat5571]

Surprisingly I twisted it by hand. Can you a faucet hose tool similar to this: www.lowes.com/pd/Kobalt-Faucet-Change-Out-Tool/1002797772?cm_mmc=shp-_-c-_-prd-_-plb-_-ggl-_-PLA_PLB_208_Plumbing-Repair-_-1002797772-_-online-_-0-_-0&ds_rl=1286981&gclid=CjwKCAiA5t-OBhByEiwAhR-hm_HPpUilFKlKCIsVGXUxrLvdzO3CUwkNx9izL129cPJTZr-8omlw4hoCqBwQAvD_BwE&gclsrc=aw.ds

[@AgentOffice]

Try a basin wrench 🔧

[@derickbrown8471]

Why didn’t you show the proper tools to use?