In this video i'll show you how i replaced FZR fork seals.
Пікірлер: 106
@Jungleland334 жыл бұрын
I always come to "how to change fork seals" channels when I want to listen to heavy metal.
@danielchris10004 жыл бұрын
🤣🤣🤣🤣🤣🤣
@jaymesoctane57323 жыл бұрын
No very helpful. Stupid music.
@stevewatkins30813 жыл бұрын
Funny that every time I hear heavy metal I want to change fork seals
@coolbreeze15642 жыл бұрын
This just sucks. They should remove this
@bobmyersco4 жыл бұрын
Way too fast, don't need the crappy music nearly as much as some good commentary about how to do it - especially the completely missing part about seating the new seals!
@mamutas36923 жыл бұрын
this video helped me a lot to replace the peugeot xps 50 fork seals
@TAPASBLITZ3 жыл бұрын
Whwre did u get the long extension tool from I need one to change my forks and I can’t do it without it
@flex36684 жыл бұрын
How did you seat the seals? That's what I'm fighting with.
@derekguidry90326 жыл бұрын
How much do you stroke the rod ,Or do you keep going until the contents empties?
@aidentaylor66716 жыл бұрын
Thanks for replying, only asking causd just got my bike, and never really needed to buy tools before until now. And my folks are leaking a small bit. Just ordered a seal mate. I'll see how that fairs
@wilmersegarra15745 жыл бұрын
Are these forks from a Moto Guzzi? How many miles should the oils on folks should be replaced?
@ohstv_photopro4 жыл бұрын
How much fork oil did you put in?
@gixxeride88motovlog3 жыл бұрын
how about gixxer? do I need to remove the inner tube.
@gummitarzan85453 жыл бұрын
gotta love the camera angles
@johntray14623 жыл бұрын
Hi I think this is the first time i have seen some one using a very long socket to be use as inserting into the folk to aid the removal of the Allen bolt at the under bottom of the folk housing my question is what is the name of this extra long socket ? and are they only needed some times thank you in advance , john from Manchester England
@barty1111113 жыл бұрын
Hello John, it's just long threaded bar with pair of nuts tightened against each other - very cheap gadget :-)
@johntray14623 жыл бұрын
ok thank you i will watch the clip again to see what it looks like if i can pause at the right time
@aidentaylor66716 жыл бұрын
Hi fella, what's the chance you could list the tools needed to change the folks
@barty1111116 жыл бұрын
there is no unusual tools needed, only special tool is the long key to loose nut on the bottom inside fork which can be made out of usual stuff as a threaded rod with 2nuts on it (size depends on your type fork), set of alan keys required.
@ranveerkumar4106 жыл бұрын
200ml shocker 100ml+100ml eingein oile=200ml super best idea
@joseamador29285 жыл бұрын
Hola Amigo, buen video, solo tuvisteis un herror, no mostrastes la cantidad de aceite que le aplicasteis a los amortiguadores. Saludos desde Honduras.
@mandarzambre4384 жыл бұрын
THANK YOU
@ricky495 Жыл бұрын
nice video, but how much oil i have to use ?
@brentsmith56472 жыл бұрын
Brilliant video thank u, 😍👀👀👀👀😀😀😀😀😀👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍
@vulcanizer444 жыл бұрын
ok i see another problem at 6:13, you're pouring in fork oil back into the fork tube, did you just reuse your oil fork oil? and what about the bottom 6mm allen bolt I didn't see you install and torque that bolt into the damper rod
@masheercatchers30106 жыл бұрын
plz explain tool name. how many needs tools???
@qaisarilyas19484 жыл бұрын
Ap hame cd 200 ke front shock seals no bata sakty hai please reply fast
@sokratissokratous99134 жыл бұрын
Does anyone know how much oil need each fork for honda shadow a.c.e 750cc 1999;
@charliebrown4214 жыл бұрын
all the reassembly part is missing
@meranwilson12514 жыл бұрын
You completely missed out the point where you reseat the new seal and fit the circlip. That's my biggest headache.
@kelekilla4 жыл бұрын
Should be called how to chango oil fork i didnt see more than that
@owaiskhan6 жыл бұрын
Which oil you used for it?
@barty1111116 жыл бұрын
owais khan Any fork oil with recomended viscosity (as manual says) or you can choose the viscosity to be hard or soft as you want
@larrymckenna35036 жыл бұрын
love the tune who is it please vid good to !
@erikchavez89056 жыл бұрын
what size nut did you use to remove for the inside of the fork?
@barty1111116 жыл бұрын
Erik Chavez Hi mate, it depend on your type of bike, fork. Do some searching on google for your bike's fork :) (I think, mine was 16mil hexa)
@jonsavary56676 жыл бұрын
For my 2000 Kawasaki KL250G Super Sherpa I used a bolt head that was 7/8" or about 22 mm.
@NnandhakumarR5 жыл бұрын
Bro... Today I changed fork oil also by the mechanic. But now front fork suspension is harder than before. Is it ok ? Or after some kilometres it will be ok? What can I do bro?
@barty1111115 жыл бұрын
Hi man, could be different viscosity of oil, or there was a little bit less oil before the change :-) If it's not really bad, I think it's nothing to worry about.
@dayanandkamble53085 жыл бұрын
Bro atakta huaa socp ok hota kya
@veenabissa20825 жыл бұрын
Thanks
@barringtonanthony2875 жыл бұрын
Veena Bissa Vic.
@travelfoodandnature47826 жыл бұрын
how much shocker oil u filled in it ....
@bhalhakhadyhan5 жыл бұрын
Mine does not have any indication on how much oil it has.
@bhalhakhadyhan5 жыл бұрын
In the manual i mean
@aegisaxhari8687 Жыл бұрын
What bike fork is this
@gehleeace5 жыл бұрын
How much fork of honda125
@jellebel2226 жыл бұрын
Mine are leaking pretty bad i was hoping you could chainge them without taking the forks apart😅
@kirkgrishamavecilla19956 жыл бұрын
jellebel222 hahahaha me too finding a video like that
@Typhlosion1006 жыл бұрын
Take them apart and clean them up or take them to your local motorcycle shop
@craigdyas36546 жыл бұрын
looks like you accssidently cut the part where you fitted the oil seals totally from the video
@mrdorey59475 жыл бұрын
The only bit I wanted to see.
@philhill79732 жыл бұрын
Didn’t show how to get the seals in !!!!
@sachinsarpal29596 жыл бұрын
shocker brn da asli trika mere kol
@bidyutbairagya8224 Жыл бұрын
Honda cb shine sp bs4 kithna ml froge oill totaha
@davekendrick72315 жыл бұрын
You didn’t show the viewers how to seat the seals. Waste of time
@loyddaez21466 жыл бұрын
My fork seems leaking little by little but not a lot.
@richardfields32482 жыл бұрын
like the white t-shirt with oil and grease mine would not stay white lol
@zankobal72425 жыл бұрын
Songs name?😍🤘
@MicMurphy19816 жыл бұрын
Man in this video you are going too fast brother you got the video going too fast slow the video down some a little bit
@josedaniel47256 жыл бұрын
Dig the guitar on video, who plays it?? Joe Saturani
@jamieforsyth52815 жыл бұрын
Jose Daniel must be a secret.
@mdsshahid69925 жыл бұрын
Fork oils kotu garm dite Hobe
@hultclovis5 жыл бұрын
The video does run a little fast. My biggest complaint is that U skipped actually installing the seals. Sure! U hit the seal with the ol' meat hammer a couple whacks but I'm thinking U had to use more than that. Didn't earn a sub from me this time...
@chillytheibault25356 жыл бұрын
Dude, waaay too fast !! Can't decipher WTF you're doing due to the SPEED & BAD BAD BAD CAMERA ANGLE. LAY OFF THE METHYLATION]
@durgeshjohndurgeshjohn68755 жыл бұрын
Chilly Theibault
@CrisDosGiulio6 жыл бұрын
Damn, you should SHOW APART the SENSE of the OIL SEAL RINGS are mounted 🤦🏻♂️👎🏾
@paekeajiab47433 жыл бұрын
I have changed fork seal and it is leaking a little again... Why??
@barty1111113 жыл бұрын
Perhaps the piston surface has some scratches or the seal was damaged during the instalation
@vulcanizer444 жыл бұрын
you made a mistake, because I see at 5:15 you are about to install a new oil seal onto the inner fork tube, but you cleaned off both inner and outer bushings, you really should replace the inner and outer bushings also with new because by just changing the oil seal on your fork it is going to leak again and you'll have to change out to new oil seals again, to do this job right change out the inner bushing you see there on the lower part of the inner tube, and the outer bushing that you removed and cleaned off then re-installed on the inner tube, reusing the washer that goes on next is ok then install your new oil seal and after all that is installed and set up on the lower outer tube, then install a new dust seal, and rub some fork oil around on the inside and outside of that new oil seal so it can slide down onto the inner tube easier without doing that with a dry oil seal
@MMKJ5 жыл бұрын
Thanks 😂
@roby145 жыл бұрын
Too fast Dude. Love the guitar work though.
@luki25255 жыл бұрын
Music sucks....
@GurmeetSingh-mt8jr6 жыл бұрын
Slow work please
@mr.singhss6 жыл бұрын
Bhai tu slow bana ta to sahi tu galat ka r raha h
@allurandomoran72305 жыл бұрын
Whats fuckin wrong with you pal??.is your video doesent know how to play in normal or in slow motion??.just asking man.tnx that youve read my txt and now your video is in normal and pleasant to the eye..from philippines with love..
@westlake90963 жыл бұрын
You are kidding 😂
@leeberry31554 жыл бұрын
No explanation,music is annoying ,got 10 seconds before turning off m8 😒
@timdougall5415 Жыл бұрын
Sorry mate, didn't get any of that
@helixsohra5 жыл бұрын
Too fast
@MrHevychevy5 жыл бұрын
Lose the muzak
@rimtibhowmik83275 жыл бұрын
Baal
@teddysgunshop23185 жыл бұрын
I’m ready to throw up can u go a little faster
@gregjacobs85443 жыл бұрын
You ok teddy?
@chriscs90803 жыл бұрын
Muteee
@nathantaylor45383 жыл бұрын
Christ what’s with the music?!
@darekwilinski79473 жыл бұрын
Na cholerę ta zastana muzyka Gitarowa ?Co to ma podkreślić....
@crispinswainstonharrison90424 жыл бұрын
Useless. Can’t see what’s going on
@bobgibb27813 жыл бұрын
This is not an instructional video , it's a " Hey look at how clever I am " video . Pointless .
@corjuleskandou82583 жыл бұрын
Bullsheet !!!!
@taylorpatnode67893 ай бұрын
This DOES NOT WORK on 90% of forks.
@stevenharris77882 жыл бұрын
Not good
@tartantam34054 жыл бұрын
Too annoying, couldn’t be bothered watching. Just cut to the chase!
@tvdinner325 Жыл бұрын
Please. Lose the horrible music.
@johnranallo4242 жыл бұрын
Stoopit music gave me a headache.
@motoryzen2 жыл бұрын
Stupid.....stupid. (facepalms) Also, there's this thing called MUTING something. You probably have a dedicated keyboard hotkey ( if you were on a desktop when you watched this days ago), and also if not...worst case...you can LOWER the volume other ways be it turning your speaker knobs, or if on laptop...I'll bet you anything you had a dedicated mute button there. If you were on a phone, you already knew where the volume buttons were.. It's not like this video's host said anything in the video. Go cry a river back to teenie bopper radio station catering land.
@williamdewarrenne58482 жыл бұрын
Made a mess of the vid by playing it too fast,,and not every body likes headbanging 'music'.when trying to concentrate.