How to Replace Oil Pump 2007-2013 Chevrolet Silverado

[@TRQ]

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

[@BanditWon]

Truly an excellent example of how to perform the procedure. All example and no extra wasted time talking. Excellent production, great lighting and camera. Very professional. Well done! 👏🏼

[@MintMonte87ACSS312]

This guide is fine and dandy long as it’s a 2wd your working on. On a 4x4 you have no choice but to drop the front diff if you want to take the oil pan off to replace the pickup tube. If your doing just the pump, you can put a wire in around the bolt that holds the pickup tube to the pump, and break it loose with a small 10 mil wrench, then use the open end to take it off. The wire is so you don’t drop the bolt but if you get a piece of thicker wire that holds it’s shape but can still be bent, and use it during reassembly to hold it against the bolt flange, and use your open end wrench to get it started just like you used it to take it off to begin with. You do not have to drop the pan to do it like most people believe.

[@larryphillippe9750]

Oil pressure went to zero. Stopped 2010 Suburban (165,000 miles) and restarted, pressure was low about 20 pounds. Replaced sensor, no change. Upon replacing the oil pump noticed the Oring on the oil pickup tube had shrunk causing air leakage. The oil pump was not at fault.

[@wishiwsthr]

Extremely well done video thanks, you didn't mention the timing chain oil cover seal might need replaced or inspected

[@jagboy69]

Nice demo... Best part, after you go through all this asspain, your oil pressure won't be any better than it was before!

[@almost1988]

Gotta love the handy dandy battery powered knuckle buster...good shit bro... bought a used 2013 ppv at 160k, im pretty sure this will be my next step. Oil sensor slows just goes from 35 to 10 over a 5 minute span, then low pressure shut engine alert on the dash info screen appears. engine still purrrrs, no knocking, but still fill it could be an issue.

[@TheStevedie]

I have a P06DE code on my 18 colorado and this is looking pretty similar to what I think I'm going to have to do. Great video

[@Vanguardsystem]

Thank you for this video. Very well done and super informative.

[@TRQ]

+TJ Hydro Thanks for watching our video! 1aau.to/m/Shop-TRQ

[@Vanguardsystem]

Thanks!

[@devinkirkpatrick6179]

what about priming the new oil pump?

[@talentsfaith6641]

Excellent walk-thru. Explained better than other videos on youtube. I see others are commenting about priming the oil pump. I know there is a plug in the block that can be removed to do this, right behind the power steering pump. I've seen others fill the pump when installing it, but that seems less effective. And, while you didn't mention it, I see that my front cover gasket set includes the seal that fits the harmonic balancer shaft. Should this always be replaced when the gasket is? One other thing you mention installing a new harmonic balancer bolt. Are these single use bolts?

[@bomkerful]

Great Video my guy !!!!!!!!

[@vincentforsberg4102]

You guys have it easy with a vehicle lift. Rest of us aren't as fortunate

[@omarrodriguez9957]

I really hope I dont have to do this 😂, currently dealing with low oil pressure replacing sensor tomorrow but I have a major feeling I’ll be dealing with this next 07 VortecMax

[@caliguy1500]

Great video but you forgot to do the pump alignment. Put the pump bolts on hand tight and then rotate the crank one full revolution. Then tighten down the pump bolts. Failure to do this can result in premature pump wear and failure. You also need to prime the pump after install.

[@recordmister1766]

Hello, do you need to prime the oil when replacing the oil pump and oil pickup tube for first startup?

[@tomference4618]

..excellent presentation!

[@savr4429]

Is this the same for a 5.3 liter - 09 Tahoe?

[@9014jayvictor]

ty ,.. great demo !

[@oldheadneverlacking7010]

Gahhhhhhdayuum. Might as well take the engine out

[@HuhXcontext]

Very well explained

[@michaelnichols1614]

Prime the pump? Alignment tool for the front timing cover?

[@elmergarcia818]

Job like this how much should it cost ?

[@pcdetail602]

Do you need to prime pump before installing ?

[@brandonchustz]

What is the part name of those side covers at the rear of the oil pan? I’m kissing one and having a hard time finding a replacement. At 16:46

[@BennyPrice-l8j]

Yeah front seal should be changed and mine. has. Oil cooler lines other than not changing seal and he could have said some had oil. lines He done a. Excellent job

[@mattblack133]

No shimming the oil pump before you torque it down and no alignment of the crank seal???

[@andriianhelovskiy7003]

What about shimming this pump?

[@ravamclaine6308]

What about priming the oil pump?

[@georgerivas8929]

Can you guys make a video for 2014-2018 Chevy Silverado (version) plz

[@billhackley3540]

is the procedure the same for 5.3LT

[@gjoniny]

how about putting oil in first, then the coolant, then starting the engine?

[@jdrissel]

Oh man. I have a '11 z71 and I am getting inconsistent oil pressure and the rear main seal is leaking.... I suspect that I am in for a big repair bill. Just the rear main seal was quoted at $2500.

[@9014jayvictor]

liked and subscribed

[@davydoom]

Did it work though?

[@lylegoodluck]

Is that crossmember removable on 2wd?

[@TheOpinionSports]

I believe my oil pump is going bad on 2008 Chevy avalanche, how much do people normally charge to fix these?

[@dannynguyen6374]

I don’t like how you have to take off the diff just to get to the pan.. doesn’t seem efficient 🤦🏻‍♂️

[@andrewdestin]

Awesome

[@alangalindo9051]

Hello, how are you? I have a question, how much do you charge for a job like the one you just did? 😊

[@daman7517]

Not true I have had mains down 4 times due to oil pick up tube o ring , piston removal twice and removal of original gasket leaking an never removed diff and I was laying on my back.

[@dannynguyen6374]

Same engine inside of a 09 GMC Sierra?

[@buckwild6587]

What is the sensor at 20:00?

[@buckwild6587]

Ok nvm I wasn't patient enough 😂

[@travisbaseball13]

Is this a 5.3 or 4.8?

[@billmonroe8826]

You didn't shim the oil pump. In my observation, it shouldn't be that big of a deal but is that the reason you didn't?

[@imjonky]

What puller size

[@johnshanahan6439]

You never mentioned anything about priming the pump.

[@AnthonySandlin-k5p]

After watching this I've come to the conclusion I'll sell my truck if oil pump starts going out

[@warderic]

Seems like it would just be easier to pull the whole damn thing

[@prestonalexander4628]

Dont you have to prime the oil pump

[@FelNoobs]

I think I will look for someone who does this

[@dowfam]

Ok I’m over 20 mins into this video and he is still taking half the truck apart…..

[@eldianmolina4920]

106 inch pounds?

[@anthonyagostino5732]

Man what a waste of time!

[@Vanguardsystem]

Thanks!

[@Vanguardsystem]

Thanks!

[@Vanguardsystem]

Thanks!

[@slingedo2844]

Thanks!