All a charm and very clear. Those 2 screws on the disk though...jesus...still stuck at that. Had to take a break
@kieferste2 жыл бұрын
Hit the disc around the screws a few times they should break free
@betweenframesproduction396811 ай бұрын
Can I ask you How you go about jacking the car up? It looks like you do it on the pinch Welds but as far as I Can see there is not really room for both the Jack and Jack stands on the marked dimples and so one rusk bending the frame?? Thanks!
@plimsole197710 ай бұрын
What year i20 is this ? I have a 1.25 2011 comfort and noticed different varients of disc and pad available ...2 prong and 4 prong pads can you advise on the different types and what you used ? Thanks 😊
@boomshewaddywaddy2 жыл бұрын
Many thanks for the video! About to have a go at this next week so this will be a big help! Really like that electronic torque adapter, where did you get that from? I’m interested in grabbing one myself.
@kieferste2 жыл бұрын
You can get one from machine mart there really good
@Patrick-qc4zy2 жыл бұрын
How do you know what torque you need to be at ? Is it in the car manual ?
@TheMisterB2u2 жыл бұрын
Silicone grease might be better for slider pins?...and what's in that spray bottle?....better than brake clean aerosol? Good video and very clear images,thanks for posting!
@kieferste2 жыл бұрын
It's just brake cleaner in the bottle mate I've upgraded the bottle too 👍
@TheMisterB2u2 жыл бұрын
Like another person added, silicone grease better for slider pins! Can I ask what's in the spray bottle?Brake cleaner in a can £6 ,but can you use a homemade solution?
@kieferste2 жыл бұрын
No it's just brake clean I buy a 5ltr and put it in a bottle
@javadmoosavi27109 ай бұрын
Very nice 👍👍
@rainy60277 ай бұрын
Hi, at 15:08 i couldnt make out what you did to the caliper with the G-clamp, any chance you could explain? Thanks in advance, great video 👍
@kieferste7 ай бұрын
Yes mate I just pushed the piston back with it 👍
@rainy60277 ай бұрын
@@kieferstecheers for the quick response 😃
@graemerobertson5160 Жыл бұрын
What torque did you use for the caliper bolts when re attaching please?
@kieferste Жыл бұрын
Hello there sorry for the late reply which bolts the caliper carrier or the guide bolts I'll get both specs tomorrow if you still want them
@kieferste Жыл бұрын
Caliper to carrier is 27+4 nm caliper carrier to hub is 88+10nm
@graemerobertson516011 ай бұрын
Thanks again for the info. I did the job today. Amazingly the small Phillips screws came out dead easy but getting the calipers back to the new pad start position was murder. I didn't have the tool you used. Was quoted £240 to £280 by two Teesside outfits. Cost me £95 in bits including copper lube and brake part cleaner!
@betweenframesproduction396811 ай бұрын
@@kieferste Hi. What do you mean 27+4? Thanks?
@kieferste11 ай бұрын
@betweenframesproduction3968 so it 27nm x4 nm so it would be 31nm
@JohnWilliams-qm4qy Жыл бұрын
Very dark unable to see what's happening
@barrybritcher3 ай бұрын
Not very useful you only did fifty percent of the car. I need a video on the rear