How to Replace Rear Bumper 2000-2006 Chevrolet Tahoe

Shop for New Auto Parts at 1AAuto.com 1aau.to/c/59/bI/bumpers-and-parts
This video shows you how to install a new rear bumper from TRQ on your 2000-2006 Chevrolet Tahoe.
This repair was done on a 2005 Chevrolet Tahoe Z71 5.3L Sport Utility 4-Door 4WD Automatic and the process should be similar on the following vehicles:
2000 Chevrolet Tahoe
2001 Chevrolet Tahoe
2002 Chevrolet Tahoe
2003 Chevrolet Tahoe
2004 Chevrolet Tahoe
2005 Chevrolet Tahoe
2006 Chevrolet Tahoe
Tools you will need:
• 17mm Wrench 1aau.to/oU8/1AXAA00010
• 15mm Socket 1aau.to/obsD/1AXAA00015
• 17mm Socket 1aau.to/obsD/1AXAA00015
• 18mm Socket
• 21mm Socket
• Needle nose pliers 1aau.to/oC5/1AXAA00051
• Needle nose pliers 1aau.to/oC5/1AXAA00052
• Ratchet 1aau.to/obzw/1AXAA00016
• Socket Extensions 1aau.to/obsD/1AXAA00015
• Gloves 1aau.to/o3L/1AXSS00048
• Safety Glasses
• Pole Jack
Subscribe: / @trq
Check out our playlist:
Chevy Tahoe 2000-06 2nd Generation: • Chevy Tahoe 2000-06 2n...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

[@charleshurley7255]

Good video, thanks. I found a short cut on my 2004 tahoe. I just removed the 2 18mm bolts and the 15 mm bolt that connect the frame to the mounting bracket. The bumper slid right off with the brackets still attached. The three nuts were welded on so no wrench needed.

[@oscarjones5773]

Best video on here for this. Well done

[@lrmusic8754]

Thanks for this video I'm replacing mine on my 03 tomorrow

[@IVIodernWarefare2]

Great tutorial!

[@jennifercousins9603]

What size are those wire harness clips, I need to replace mine

[@drewskidrankthebrewski4657]

If i cannot access the spare tire/or the hoist mount from the underside of the tahoe will this allow me to access and remove the entire hoist? I have tried all the tricks to lower the tire ive found on youtube and have had no success in even lowering the tire a mm, and its fully hoisted up to the most it can be lifted.... Im trying to remove tire and hoist so i can replace with new updated hoist that wont get stuck. Thank you

[@Oxnard5150]

Is the 2003 escalade tge same?

[@gangsta-F22]

This would work for suburbans?

[@Markkent77]

Is there a video on how to remove 2001 Chevy blazer back step bumper.

[@TRQ]

+Rocky Drago77 We do not have a video for this repair right now, but we'll keep this request in mind for a future video! 1aau.to/m/Shop-TRQ

[@UnknownMe321]

too much rust