How to Replace Rear Caliper 2006-12 Ford Fusion

Buy Now!
New Brake Caliper from 1AAuto.com trq.video/ia-R...
A worn out or seized brake caliper can create dangerous and expensive problems: overheating, rotor and pad wear, or even total failure. TRQ brake calipers are engineered to fit your specific vehicle. This video shows you how to a rear brake caliper on your 2006-12 Ford Fusion.
• Check here for more videos on the 2006-2012 Ford Fusion: • Ford Fusion 2006-2012 ...
This repair was done on a 2011 Ford Fusion SEL 3.0L Sedan 4-Door AWD and the process should be similar on the following vehicles:
2006 Ford Fusion
2007 Ford Fusion
2008 Ford Fusion
2009 Ford Fusion
2010 Ford Fusion
2011 Ford Fusion
2012 Ford Fusion
Tools you will need:
• Pocket Screwdriver
• Pry Bar trq.video/oCH-...
• 10mm Socket trq.video/oaxr...
• Hose Clamp Pliers trq.video/ody-...
• 3/8 Inch Impact Gun
• Ratchet trq.video/oaVL...
• Socket Driver
• Torque Wrench trq.video/o9v-...
• Brake Grease
• Liquid Thread Locker
• Drain Pan
• Floor Jack trq.video/oIB-...
• Hammer
• Jack Stands trq.video/oF4-...
• Wheel Chocks
Subscribe: / @trq
Check out our playlist:
Ford Fusion 2006-2012 1st Generation: • Ford Fusion 2006-2012 ...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

[@bryhut17]

Add in the sizes of the sockets used, and this would be perfect.

[@sylvestergayekpar3699]

Great video just wish u stated the socket sizes

[@danielgag8852]

Excellent video. Helped me every step of the way.

[@kimbalmccoy4892]

The best video I have seen on how to remove and replace the parking brake cable on my Lincoln MKZ. Thanks!

[@EvilSanta482]

You really should use blue thread locker not red unless you really want to use a blowtorch to get it back out if you ever need to remove it again.

[@dmull515]

These videos are so good. Great job!

[@onewaynestreet]

Thanks for the vid. I knocked out the job like a pro.

[@stevekennon1786]

Great video...as is all of the TRQ videos. Please do a video on how to replace the starter for 06-12 Ford Fusion. Thanks !

[@stevekennon1786]

Great video ! Please do one on how to replace the starter for 06-12 Ford Fusion. Thanks

[@hoosiered471]

Great video with detailed instructions!!!! Thanks!!!!

[@randomcontenttv2118]

Can't get my e-brake bolt off my 2011 Ford fusion sel any suggestions

[@nateladd2157]

since the fusion and milan are the same car for the most part, will i be able to use this video for my 2010 mercury milan?

[@dillonsouriol1919]

So you don't have to bleed the whole system if you Crack just one line 🤔 I

[@larylhuntington5398]

Great video. Going to help a lot.

[@robertlandrum8598]

Great video !

[@whobitmyname]

Me at the end: "if he doesn't do the star pattern I'm disliking this whole vid."

[@martyforgigs]

You are the best!

[@andrewhammer4375]

i'd be lost without you lol

[@markzgagowski6099]

Two questions. Did both of the rear calipers, rotors and pads along with front pads and rotors. Bled the rear calipers and breaks are squishy. They stop but don’t feel as firm as I thought they would be. I’d say 3/5ths of the way down for significant stopping. So I bled them again. This time i did the rear and front but when I went to get the nip off of the front it snapped the top off. What do I do now? I bled 3 out of the 4. I also did them rear right rear left tried front right and the. Front left. Stopping at about halfway down. Could it be that this is how firm the brakes are on 08 Milan? Ty😅

[@eliselozzio2292]

Go get your vacuum pump checked out has to be down in shop.

[@TheGb50]

You need dot 4 now on that car they have a recall on that car

[@armandhammer9617]

So you totally skipped over the spring..

[@kennethelandry3804]

I can’t fined where it tells you what wrenches to use , had to go to someone else

[@rodolfohuerta2303]

Better good class I am a mechanic now

[@robertscott1156]

Not red thread locker. Blue or orange.

[@lyndonk2407]

Peeton hole