How to Replace Transfer Case Actuator Gear 2004-2010 BMW X3

Buy Now!
New Transfer Case Actuator Gear from 1AAuto.com 1aau.to/ia/DMTRX00001
This video shows you how to install a new transfer case actuator gear on your 2004-2010 BMW X3.
This process should be similar on the following vehicles:
2004 BMW X3
2005 BMW X3
2006 BMW X3
2007 BMW X3
2008 BMW X3
2009 BMW X3
2010 BMW X3
Tools you will need:
• Pocket Screwdriver
• 10mm Socket 1aau.to/ouS/1AXAA00017
• 13mm Socket 1aau.to/oyu/1AXAA00015
• 18mm Socket 1aau.to/okQ/1AXAA00043
• E12 Inverted Torx Socket
• T20 Socket
• 1/4 Inch Ratchet 1aau.to/ouS/1AXAA00017
• 3/8 Inch Drive Ratchet 1aau.to/oyu/1AXAA00015
• Socket Extensions 1aau.to/oyu/1AXAA00015
• Torque Wrench 1aau.to/opR/1AXAA00044
• Gloves 1aau.to/oc9/1AXSS00048
• Center Punch 1aau.to/obs/1AXAA00055
• Floor Jack 1aau.to/ohN/1AXAA00068
• Hammer 1aau.to/og2/1AXAA00091
Subscribe: / @trq
Check out our playlist:
BMW X3 2004-10 1st Gen E83: • BMW X3 2004-10 1st Ge...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

[@hal6672]

After all that work he puts on a brand new actuator... says a lot about replacing the plastic gear

[@jhfl1881]

Nothing wrong with the gear as well. He could have tried to find a stripped gear to show why one should replace it.

[@twilliams3904]

No is watching it🤣🤣🤣🤣

[@ron8566]

Nice work - I learned alot. Rather than fitting a replacement gear I would spend the $80-$128 for a new actuator motor and case with new mounting bolts. Good stuff nonetheless. Thank you!!!

[@Le3icester]

i just fixed mine i just rotated the Gear 180 degrees works like new lol

[@edorofish]

The old switcharoo! We caught you!

[@virgilmobile1]

Replaced my plastic gear as shown.The replacement was out of round.This caused binding as the motor turned when bench testing the acuator before installing it.Replaced the plastic gear again and shimmed the motor mount so it would turn smoothly.

[@aircooledshack7154]

So if replacing the gear is the fix why fit a whole new unit at the end?

[@luisvaladez8486]

Pull the motor remove the gear assembly from the main motor assembly..then turn the gear 180 degrees. You're good to go for another 100k miles. Nothing to buy

[@ibdewett5032]

hey seen video wery good but why put new on if yuo have fix the old one on video does it need to be ajustet after

[@FraxinusExelsior]

Great instructions!

[@lakomacias5160]

Im doing 1 next monday...how much should I charge...thanks...you videos are su helpful...new subscriber here😅

[@Judah28]

Do you have one for bmw 2 series gran tourer

[@randyerwin2109]

I thank it is great showning the video

[@Davenz]

Ours is wearing out in 50,000 kms. We had 4 new Bridgestone tyres that match the door jam label, with exception of speed rating, so rotational difference should not be a factor. BUT, the trifecta of lights comes on every couple of days, goes off after a couple of engine restarts. Any clues why that would be??

[@askershabdeen3376]

Good job

[@markobrien4005]

Rebuilds the actuator motor, obviously struggling to get the cover to stay down when peening it, next shot is a obviously new actuator motor being installed. Nice idea but peening aluminum is not easy and to try and get a good seal on that cover would be difficult.

[@glenglene8473]

what is the symptom if the gear broke?

[@Amirsabha786]

Why you installed brand new one?

[@not_virtuality]

I just did this job without removing anything

[@carlosfletes1730]

Ese que está instalando, está completamente nuevo XD

[@user-hk2zg4ch2b]

BE sure to buy the BRASS upgraded gear

[@mikecamacho1934]

Can get a whole new one for under $100

[@supercrack27]

Jajajajajajaja después de tantas historia va y lo cambia por uno nuevo 😂😂😂

[@imbohica3933]

Wtf man after all that you just put in a new motor

[@user-md7sc5ny1f]

Just a bit of warning. The bolt head holding the Transfer Case is 18mm (not standard!)(The bolt is M12, and 18mm heads are not recommended for designs by standards. However BMW tried and succeeded to make it very difficult and expensive to repair). I have a large key set and the 18mm hex key is not included. It is torqued really hard and with the inevitable rust it is very hard to take off. You need an impact rated swivel+impact gun since the design of the bracket is Terrible!!. And yes, you need a car lift, and possible a second person to help. And more, a welding torch was needed to heat up de bolt so it can be taken out. Some say that the bolt is locktited in place so when you try without heating it it breaks and then you really need to go to the dealer! The plate holding the white plastic gear must be sealed against the actuator case rim after the new gear is mounted inside. Otherwise water and salt will go in and ruin your actuator in not so much time! The car also expects after the repair to have a program run on a BMW OBD programmer, to have an adjustment done before driving. Another program must be run on OBD when you replace the TC fluid. So yes, these can be done with a specialized BMW OBD scanner tool only not with any tool.

[@HeadshooterGTAS]

a plastic gear what a stupid idea bmw

[@blackdick74]

This makes no sense why put a new one after all of that?