How to screed/bedding bathroom floor/shower professionally/DIY beginner tutorials.

Steps
1) mixing sand and cement.
2) do the slurry before screed.
3) spread your mixed screed on the floor.
4) grid lines.
5) screed and finishes.
Any questions leave in the comment section.
Thank you everyone.🙏

[@rossclay4896]

Would like to watch without the music. Thanks for sharing your skills.

[@armans_h6820]

You are amazing bro good luck

[@monbaby77]

very good demonstration.

[@QLHTilingWaterproofing]

❤️❤️

[@1227babo]

Pretty good job!!! Mate!!!

[@QLHTilingWaterproofing]

Thanks mate

[@diamondavey]

good video

[@QLHTilingWaterproofing]

Thanks for the visit

[@weskotob]

Good job

[@QLHTilingWaterproofing]

Thanks

[@user-dy3jl3uy6p]

Great work! But that bloody music. I had to keep turning the volume down and then quickly back up when you were talking to understand.

[@piotrjaniec9139]

Thanks for your video, How quickly can you tile over it please?

[@benjamindelfs2718]

Just a tip for you. If you set pads with your laser around the room you can take away the guess work and not need to use spirit levels as much and use straight edges. You’ve definitely improved your work over the years

[@fufuelhatch444]

What’s pads ???

[@benjamindelfs2718]

It means heights. So you have something to screed to rather than just using a spirit level. It’s what most us tilers do now

[@user-ch8jj1lx7k]

@@fufuelhatch444 it could be just a piece of tiles you put on the screed to get the right height with Laser so you dont even have to guess work as he mentioned. I do every time, and exactly I have got what i want.

[@pardeepsaini5896]

​@@user-ch8jj1lx7kcan u pls tell me how much fall is required in bathroom floor?

[@Dannytranst]

Hi mate, what is the ratio for sand and cement when mixing them

[@kylielee2825]

Great video thank you! I’m trying to achieve a concrete with glow rocks like exposed aggregate look in bathroom. Would it work by following your video and seeding at the end? Any advice would be greatly appreciated TIA

[@samwaller2925]

You need to pour a concrete slab then have it polished

[@DigitechLand]

what ratio sand to cement for screed?

[@alexanderchuyko4889]

It`s the best tutorial! However there are some questions- what exactly you use as a slurry? Just cement mix or any chemical improvers or a fiber fluff? How to know the ratio of this mix, please? How you maintain an exact required thickness of the screed? Sometimes it is limited by tiles layout and ceiling, windows seal or niches configuration. Do you add any supplements to the screed itself or a standard 1:4 cement/sand ratio? Does this method have any limitation with a min, thickness, please? In our case, the highest point (perimeter) is counted ~22-23mm, but at the centre of drains it must be ~12mm only. Some traditional specialists told me that 25mm is absolutely min. thickness of such kind of screed. Is that correct? Thank you

[@QLHTilingWaterproofing]

Hi Alex Thanks for tuning in mate. 1) slurry is just Cement and water mixed together. There is no other chemical in the slurry involved. 2) Ratio! Long story short. For 20 litter of water you need 10kg of cement mixed together or you can make it more thicker by adding more cement if you want. 3) prior to screeding you should know the hight of the ceiling your full finish configuration. 4) screed thickness, I wouldn’t go less the 20mm with screed nor thicker then 60mm with mash in.

[@afntiling]

The best tiller in the world 🎉

[@geoffstein3896]

Hi mate, are you just going thr thickness of a tile below the water stop please? Thank you

[@KizWhalifa.]

Tile thickness plus 3-5 mills to allow for glue

[@petermorgan3332]

What ratio of sand and cement

[@rio20d]

I assume this is waterproof membrane under screed?

[@benjamindelfs2718]

If you go to Sydney tools they have these lightweight white levels just for screeding, they’re very good for screed. Also I use a plastic float to get the high points off

[@QLHTilingWaterproofing]

Thank you for comments we will check them out.👌👍

[@benjamindelfs2718]

@@QLHTilingWaterproofing yeah what’s your phone number and I’ll send you a link. You use them just for screeds

[@QLHTilingWaterproofing]

Hey Mate search QLH Tiling and waterproofing on google, Facebook, instagram you will be able to find our contact details. Thanks QLH

[@donnastein4946]

That screed is a work of art I love how easy you make it look. How much of the water stop are you trying to leave exposed, are you working out roughly the thickness of the tile and roughly the glue underneath? Thanks

[@QLHTilingWaterproofing]

Hi Donna Minimum 30mm screed otherwise it will become drummy and no you can not do it roughly you need to know your thickness finishe.

[@donnastein4946]

@@QLHTilingWaterproofing Thanks for the reply. I'm just wondering how you judge where that water stop angle is going to need put, do you find out the size of shower screen the customer is getting then just measure off the wall the thickness of the tile plus glue to work out exactly where the angle water stop needs to be? Thanks

[@soccerkills]

Good job but cut the music man

[@jerryyi4394]

Hi, I saw there is tile over shower tray. So no need to screed.

[@diamondavey]

lol

[@ghulamreza7578]

😂😂😂😂😂😂😂

[@johndavid3474]

The ratio of music to your voice is 4:1

[@Naderhaidari]

You should learn screed from me. The way you did is completely wrong my friend. You can’t tile that properly

[@marvelousmkansi8772]

I would like learn

[@richardknight6539]

Are you a tiller cos your definitely not a screeder

[@aaronh920]

fuck the music off bro, its loud af, didn't u realize ?