How To Service Seiko VX42 VX32 Quartz Movement | Assemble and Disassemble | Watch Repair Channel

[@sirmikon]

this was extremely helpful. I needed to remove a broken stem from the VX42E. The only tricky part were the 5 center gears and the stem-holder above the plastic gear. I couldn't tell which direction they went. Is there a tutorial on which directions the center gears go? This is my first time disassembling a movement. I'm only hearing a tick every 2 seconds and the new stem isn't holding 2nd position.

[@cadmanleung6896]

Very helpful video! do you have any videos on what to lube up for the gears etc for this movement? Don't think I saw any?

[@ConteMontecristo]

No need, a new one costs just a few bucks. It's not worth it. Cheers!

[@johndally5247]

Great video, but does the movement work after you have disassembled and reassembled it? if it does could you please show it going at the end.

[@ImaginaryEvil]

That's the point of a service 😊

[@gaborm4767]

Which one is the motor? 5:39?

[@SolimBD]

It's a rotor

[@federicomaraschi4438]

in your opinion, is this a good movement?

[@SolimBD]

Not bad. This is a good movement also.

[@leonard8217]

plastic, no good

[@scdevon]

@@leonard8217 They might be plastic, but they keep going and going....

[@leonard8217]

@@scdevon yeah absolutely true. However, I am just a bit idealisty about quality.

[@gratmatassa5432]

@@scdevon they're a very good movement, as for servicing why bother you can buy whole movement for pennies.

[@bismillahckm144]

Very good video

[@SolimBD]

Thanks

[@armadillofz1]

This is all great, but how do you remove the stem???

[@SolimBD]

How to remove stem, watching the video kzbin.info/www/bejne/pZPRi6urosaSotU

[@armadillofz1]

Thank you.

[@roadgent7921]

QUESTION: does this VX42 have a trimmer regulator?

[@SolimBD]

Regulator only automatic movement

[@roadgent7921]

@@SolimBD I meant Trimmer capacitor screw? (for adjusting the watches accuracy)

[@SolimBD]

Not available in the movement

[@marcialavinaavalos9013]

Gracias voy a intentarlo

[@shh88all78]

Boss, where can I get a dial for vx42 movement?

[@SolimBD]

Sorry boss, i have no idea

[@bharathdynamo9351]

bro why those 2 wheels have holes on them?

[@SolimBD]

To lighten the weight

[@bharathdynamo9351]

Oh okay , doubt cleared

[@habibsyukri6246]

omg nifty watch service neat

[@bollabathinianilkumar2229]

This moment titan case inside is comming, new key rod useing

[@ajithrampursad546]

How to test the coil ?

[@deanagoes2791]

Oh my...that it little tiny plastic gear 😳

[@sachinkokadwar3816]

Vj32 movement full restoration

[@SolimBD]

VJ32 video coming soon

[@soumitrahazra7900]

VJ42 MOVEMENT VIDEO ??

[@SolimBD]

Similar movement VJ32 See this video kzbin.info/www/bejne/iGXRp3uudtqKacU

[@a.c.1474]

Utterly unbelievable how you post an 11 minute video and fail to show people how you release the stem from the movement.

[@SolimBD]

Stem remove video, watch it kzbin.info/www/bejne/pZPRi6urosaSotU

[@a.c.1474]

@@SolimBD Thank you. There wasn't specifically a VX42 movement but I could see the Epson's were basically the same design. Sorry for being irate. I had been trying for a while to remove the stem without luck to clean a filthy lens. Job done without without the watch being thrown through a window 😂. Thanks again for the reply 👍

[@SolimBD]

Thank you so much