Great video. Thank you so much for the explanation about how the rear diff is actually pointing UP when the measurement device measures it as being down. That was kicking my butt and no one could explain that to me.
@bradmccracken83042 жыл бұрын
So many people say just set the diff pinion down 3 degrees 🤦♂️. Thank you for clearly explaining what’s actually involved 👍
@Brendan.Wheatley2 жыл бұрын
Thanks for another great tech video, they are quite informative!
@runslikeapenguin Жыл бұрын
Huge help, measuring from my crank pulley was messing up my numbers
@nicholasash93892 жыл бұрын
If it's an IRS like on a VE Commodore you can set it all on the hoist. With the IRS, the angle wont change when the car is off the ground. Excellent video Broomy
@TheCanadianBubba2 жыл бұрын
Great explanations and information Broomy... Cheers !
@matsinkal2 жыл бұрын
Nice vid mate very informative.
@yafois9882 жыл бұрын
I installed a 3" lit kit in a 78 J10 Jeep. Now as it sits with truck frame is maybe 1 degree "Rear end up", I find results these measured numbers here below. Trans output end is 4 degree down. Driveline is 2 degree down. Diff Yoke is 11 degree Up. What would be the correct shim angle to correct for this. The Yoke at 11 degree from a Post kit results is quite extreme IMO. thx
@brick88nose2 жыл бұрын
What about left to right from pinion to tailhousing on transmission. On an offset such as an 8.8 from an Explorer has. Does this matter a whole lot?
@mikeymasi2 жыл бұрын
onya Broomy plenty of helpful info in this
@zundappwatercooler2 жыл бұрын
Who made that tailshaft loop🙈
@NUT84G2 жыл бұрын
appreciate the video, explains how to use the app properly and the slope angles, cheers mate
@MafiaboysWorld2 жыл бұрын
Off topic question: What's the HP rating on that GJ driveshaft Broomy?
@BroomysGarage2 жыл бұрын
It’s a 3.5” unit so from memory was around 1400hp
@MafiaboysWorld2 жыл бұрын
@@BroomysGarage Thanks bro. 👍
@shawnwimberly92942 жыл бұрын
Right on
@JyveKilla2 жыл бұрын
note to editor, insert link at 3:35 for previous video ;)
@psyco11222 жыл бұрын
Rather then cutting the crossmember mount, you can space it from the body with longer bolts and an alloy or steel spacer...
@BroomysGarage2 жыл бұрын
You could do that also 100%. I chose not to here because it would have meant having to remake all the dump valve hoses, and remake the rear section of the belly pan.
@bluedog37311 ай бұрын
Way over complicating a simple process. Engine should almost always bet set at a down angle. Pinion should be pointing up at same angle. I.E. 3 dgrees down, 3 degrees up. For drag racing all bets are off. Depends on chassis and rear axle mounting. No need for calculators.
@Headsup9550Ай бұрын
You CANNOT check driveline angles on a lift. Suspension must be ride height with suspension loaded. Total waste of time!
@BroomysGarageАй бұрын
Maybe watch the entire video next time champion. The car is sitting on wooden blocks when making the measurements at the end of the video.