How to setup Dome Boost Control on Holley Terminator X, HP and Dominator

[@177SCmaro]

Thanks for explaining how to wire the dome sensor on the HP. I didn't see anything in the Holley instructions about that and it was the only place I was uncertain about how to wire a co2 boost controller.

[@LSFoxbody]

Your information is awesome!!! I literally stopped working on my build (93 Coupe, 6.0, with 80mm VS turbo) bc I couldn't figure out the I/O wiring and hated calling other folks to ask. Thanks for the VERY informative videos!!! Keep up the good work and I will hit the garage and listen to the wife gripe again .....lol

[@louisdevriesoutdoors6019]

What I'd like to see is a "punch list" of the steps needed to activate and use the boost control starting the point of the mac wiring and the Terminator-x setup w/o the "you could also do this" stuff. If I can get it all to work then I can refine from there. I've never done this before, so I can't make assumptions on any step in the process. Thanks for your input!

[@Jvaughan1989]

This is great info! Been working on my junk foxbody build for a little while now. Just a gen 4 6.0 with a billet 80mm vs racing turbo and a glide. Just not getting motivated and started back on it. Love your page and content you have some really solid info!

[@Boosted370]

Thanks man this video definitely cleared the air on this!

[@dillionfindlay6129]

Thanks for the video definitely helped me I am struggling figuring out this holly x my plan was just to run a boost controller with the holly x but does not seem like that is a possibility I ordered mac valves plan on just doing a tee before gate to macs like you said I am very appreciative for you making the videos helped me more then you know where I live in southern Oregon we don’t have any speed or tuner shops so I am stuck trying to learn this all myself

[@blackwellm23]

What a coincidence, I'm finishing up this install now

[@six50motors]

Hey brotha great video I've watched it a dozen times now I have everything in software programed but I'm jus not understanding and I didn't see anywhere in video what actually starts the boost ramp and what triggers it and what happens if your jus street driving with the triggers do you need to hit button to enable on street. Thanks for the great info

[@lsxtmt4910]

Can you do a vid on setting up boost vs rpm in Term X for a street driven ratrod?Thanx for all the info!

[@joseb1700]

Great vid thnx . So if I just leave everything blanc n just setup sensor it’ll stay like before sensors n controller was installed?😊

[@justinbolton2838]

If ur running twins would u still set it up the same way meaning compressor discharge t into the Mac valves an just t off into top of each waste gate

[@MrFord1947]

So with co2 boost valves when you used pwm outputs

[@scottyjones5992]

Have you ever had a issues running pwm+ on your boost solenoid vent? I also have a hp and running into the same issue. I’m using Holley’s latest boost control solenoid setup. I see where Danny says you cannot use the HP but can dominator. Wonder what the difference is?

[@turbovicsatx2910]

Hey bro I have a question I’m haveing trouble with launch psi I get on the trans brake and set it 4 psi and it goes past that when on the brake

[@vermontate897]

Can the v5 staging be used with a two wastegate and one Mac valve setup

[@BigRichEHhthang100]

So the 3 port Mac valve should be 5volt and then ground from terminator x max ?

[@blake5605]

Could I pay you to help me out this has me stumped

[@turbovicsatx2910]

Can you just a regular relay instead of a solid state relay

[@callofgeorge]

how can i hit you up for some quick questions lol? what's your facebook.. I'm working with a sniper, so not so many config options..

[@dupont4sure]

how ironic is it that your date modified on your computer page is my youngest son Nathans birthday 9-27 🤣🤣🤣