How to Setup Mikado VBAR EVO

[@bhgant813]

Just ordered a Touch and making the transition to VBar. Thanks for the video, a lot to learn... very helpful!

[@mikeisiah1091]

@@bhgant813 i’m glad the video helped you out thanks for stopping by my channel. Have a great day.

[@SmokinandGrillinwithAB]

After watching your workflow, I see that having the right tools makes your building better. I'm inspired and going to step up my game.

[@mikeisiah1091]

Having the right tools for the job makes everything easier. Thanks for checking out my video. Have a fantastic day.

[@ThisIsSampson]

Good morning! Thank you so much for this video. I was curious, are you using the stock 17 tooth pulley that came with the RAW or are you using the upgraded 18 tooth version? I noticed you put down 18 tooth in the V-Bar. I have the 17 tooth pulley and I'm trying to figure out what my gear ratio should be. Would it be the same number you used?

[@mikeisiah1091]

@@ThisIsSampson I use the 18 tooth pulley sent you are using the 17 tooth pulley the gear ratio is 5.53 all of the gear ratios are in the manual on page 19 hope this helps you out

[@howintesting940]

nice vid, Mike. I have never flown Mikado, so I wonder what is good about it? Any better than the currently popular and cheaper Align or Goosky helis? Thanks!

[@mikeisiah1091]

@@howintesting940 Mikado makes fantastic helicopters if you like them they are worth the money

[@howintesting940]

@@mikeisiah1091 thanks! But what exactly better ?

[@mikeisiah1091]

@@howintesting940 they both are great helicopters but it is easier to get Goblin parts from past experience so I would probably go with a goblin

[@howintesting940]

@@mikeisiah1091 ok.Thanks.

[@roberthardy7868]

Why does your radio beep every twenty seconds? Can you silence the beeping?

[@mikeisiah1091]

The beeping that you hear is a safety feature to remind you that the radio, and the helicopter are still on and connected. I don’t know if you can turn that off. I wouldn’t turn it off because it reminds you that the helicopter and controller are still on.

[@very9000]

Hello. Please tell me, the maximum frequency in V-Bar Neo is 333 Hz, is it impossible to raise it higher? Am I right in understanding? This concerns the tail of the helicopter.

[@mikeisiah1091]

In order for the tail to work correctly, you have to used the frequency that is required for what ever tail servo you’re using?

[@very9000]

@@mikeisiah1091 I UNDERSTAND. THE POINT IS THAT I CAN SET THE FREQUENCY TO 333 HZ OR 500 HZ. SO WHICH IS BETTER?

[@mikeisiah1091]

@@very9000 the servo may move for those two frequencies, but it is best to set it to what the servo manufacture suggest

[@very9000]

@@mikeisiah1091 Thank you very much 🤝🤝🤝

[@very9000]

HELLO, TELL ME, PLEASE. I HAVE TELEMETRY. WHERE ARE THE PARAMETERS IN BAR CONTROL TO ADJUST THE SLOW ACCELERATION OF THE SCORPION TRIBUNUS ENGINE? (so that the rotor accelerates like a copy of a helicopter)

[@mikeisiah1091]

@@very9000 Hi I’m not familiar with the scorpion Tribuns lately, I’ve been using Kontronik and hobbywing ESE

[@very9000]

Thank you 🤝🤝🤝

[@very9000]

Dear friend, you also have LOGO 800. Tell me, please, does your tail not wag, even if the wind blows?

[@mikeisiah1091]

I do not own a logo 800 but a helicopter that big the tail should not wag in the wind

[@very9000]

@@mikeisiah1091 thank you

[@very9000]

HELLO. WE WOULD LIKE THE HELICOPTER TO RISE VERY SLOWLY WHEN THE COLLECTIVE PITCH CONTROL STICK IS MOVED. PLEASE TELL US THIS CAN BE ADJUSTED IN V-BAR CONTROL? DO WE NEED TO CHANGE THE EXPONENT (EXP) TO DO THIS? IS IT CORRECT? IF SO, WHERE IS THIS SECTION IN V-BAR CONTROL?

[@mikeisiah1091]

@@very9000 Hello giving the helicopter expo will not make the helicopter raise slowly it will just make it not as sensitive around center stick to raise the helicopter slowly it just takes practice moving the stick up slowly hope this answers your question.

[@very9000]

@@mikeisiah1091 THANK YOU. TELL ME WHERE IS THE EXPONENT SETTING (EXP) IN V-BAR CONTROL?

[@mikeisiah1091]

@@very9000 hello I’m on my way to work right now, but I will try to put up a video tomorrow to show you where expo is

[@very9000]

@@mikeisiah1091 THANK YOU 🙏 IS THERE A MENU FOR SETTING UP THE EXPONENT IN V-BAR CONTROL? I THOUGHT THERE WAS ONLY IN V-BAR CONTROL TOUCH

[@very9000]

@@mikeisiah1091 HELLO. PLEASE TELL ME, IF THE POSITION OF THE TOTAL PITCH CONTROL STICK IS AT ZERO DEGREES - CAN THIS AFFECT THE RISE OF THE MODEL UPWARDS, THAT IS, MAYBE I NEED TO SET +2 DEGREES IN THE MIDDLE, FOR EXAMPLE, SO THAT THE MODEL WOULD RISE AND DESCEND SLOWLY?