How To Setup X32 USB Output For Live Stream | Basic Mirror of Main Output

** NOTE **
Please make sure you save your scene on the console BEFORE you update firmware. Your current settings per channel will be cleared. You can reload your scene after update, but make sure to save your scene before updating.
__________
This videos covers a quick look at how to setup your Custom User Outputs to get you a mirrored copy of your Main House Mix into your Streaming Software. Most people are using OBS, Wirecast, or VMix which by default takes Ouput 1 & 2 from your USB input. Normally, this is your first two input channels, but you can use the Custom User settings to have a copy of your main output go to User Out 1& 2 and then route those to your USB Card.

[@AllamHouse]

*** NOTE *** Please make sure you save your scene on the console BEFORE you update firmware. Your current settings per channel will be cleared. You can reload your scene after update, but make sure to save your scene before updating.

[@Visitelc]

saw this way to late!

[@jasonlight1670]

I personally would not set this up this way. Does it work, yes. But you have no separate control over it. You should just send your LR bus to a stereo linked pair of Matrices and send that to your PC. That way you still have a mirrored LR mix but you have a separate volume control that’s separate from your FOH mix. You can also add Dynamics and EQ for that send also. 😁

[@indi2174]

This is where he talk about matrix kzbin.info/www/bejne/npS7dGlunralhKs

[@initialdluvr]

Are matrices the same thing as busses?

[@jasonlight1670]

@@initialdluvr No. busses are a custom mix usually. They can be setup to be subgroups, pre/post fade mixes, etc.. you can add specific channels to them at specific levels and add dynamics other effects to it. Separate from the LR mix. A matrix is a copy of either the LR mix or if an already built mix bus. You can not specifically assign a channel to a matrix like you can a bus mix.

[@richardstephens5347]

I think my church has ours setup as bus. I think it also sends out thru an aux out if I'm correct. Is this a decent way to send a mix over to our live stream? Also our live stream is all over the place some days. I still can't find a way to get the instruments and vocals not to clash. We just have accoustic guitar, digital piano, and bass going. Usually 2 males vocalist and 1 female. But they seem to always be louder than one another. Any clues. We us ecamm live to broadcast and a behringer audio interface..

[@HaysvilleChristianChurch]

If you have the need for a console like a X-32 or M-32 then your sound system is likely a lot more sophisticated than a simple P.A. audio feed. What sounds right in your auditorium can sound horrible to someone watching from home. You need to create a separate mix for your stream and if possible have a separate sound person monitoring and adjusting that mix, we used a pair of Bus Mixes for ours. The second sound person can use a tablet or PC with the X32-Edit software to control the Streaming mix, that incidentally gives you a way to train up additional sound people as they can start smaller by just working the mix for the stream before learning the rest of the board.

[@DavidDarst]

Finally!!!!... I have been scouring the internet for this. I even called the guys at Behringer and they couldn't help. I found a work around by using an mbox firewire device on my PC and running it from a stereo bus. Quick question? I want to keep the broadcast mix separate from the Main mix, can I use the same technique but using the Bus or Matrix channels as the output instead of the Main LR mix? Thanks again.

[@AllamHouse]

Yeah, I’m glad this was helpful. Here is a link to another video I made about keeping the house separate from the broadcast kzbin.info/www/bejne/iImwcpVujbOYr9U

[@bethlehembaptistchurchlanc9395]

@@AllamHouse What are the advantages of keeping the house separate from the broadcast?

[@robgillanofficial]

@@bethlehembaptistchurchlanc9395 basically just if you want the two mixes to be different for some reason

[@kevinldaniel]

Thank you for this! Your clear and easy to follow instructions is literally blessing hundreds of churches.

[@AllamHouse]

Thanks for the encouragement.

[@beregila]

You have been a LIFE saver! Solo pastor over here that has started the media ministry! We started doing this method main out thru usb to OBS. Now, I did the mix bus for the livestream according to your video, that way we’re able to modulate volume differently for livestream and FOH. Question is, how do I send out via usb the bus setup?

[@AllamHouse]

Thanks for the encouragement. Here are two videos that discuss using a MixBus for your stream. (1) This is the setup I use in my church right now and it allows to mixes with one engineer. kzbin.info/www/bejne/pn7RkpyreJpoiLs (2) This video discusses how to setup the MixBus to go out through USB. kzbin.info/www/bejne/jKmXeZ13p7mYkKs

[@emmanuelajmbiebot6047]

Hello Dave. I'm using the x32 compact at my church. After setting up the routing for USB streaming, I noticed that all mic volumes on the stream are perfect, BUT the combined music and instrument sounds are blurry or 'suppressed' so to speak. What could be the cause? Thanks

[@AllamHouse]

This specific setup takes the main mix and my assumption is that you have the instruments turned down in the house since they produce natural volume in the room. The more preferred route is to use a Post Fader MixBUS setup so you have the ability to modify the general settings (mix) for your stream. Here are two videos to help you along your journey. 1) MixBUS Stream routing across USB - kzbin.info/www/bejne/jKmXeZ13p7mYkKs 2) Refine your Live stream Mix - kzbin.info/www/bejne/pn7RkpyreJpoiLs

[@CyrilOracle]

Exactly what I have been looking for. I love how you also take time to *thoroughly respond to comments* . I'm definitely subscribing and binge watching your content. Keep it up👌👌

[@AllamHouse]

This makes my day man. Thanks for the encouragement.

[@ffhsband]

Do you know if it is possible to do this without updating the firmware? Our board is on Firmware version 3.08.

[@AllamHouse]

It is possible to do this, but you have to setup your stream on BUS 1/2 (or 9/10) since the older firmware makes changes in batches of 8. The upgrade to the new firmware is an easy process and you can keep all of your current settings. Do make sure to SAVE your scene before doing the update, but it will give you more flexibility.

[@hannah_-bf7ke]

Thank you VERY MUCH! That's EXACTLY what I've been searching to do. God Bless You and Yours

[@bugswako]

Thanks Dave! Really appreciate all the in-depth info you share through your many 'how to' videos. Keep up the great work!!

[@AllamHouse]

Thanks for the encouragement.

[@MacSoundSolutions]

Works great thanks for this, sending my M32r mix to KZbin livestream with my Nikon clean HDMI out as well using OBS.

[@AllamHouse]

I’m glad it was helpful. Keep doing great things.

[@peixeman]

This was really helpful. My church and I are pretty new to using the X32 and streaming to OBS. When the audio comes in, it's a pretty quiet, but I fixed it in OBS with a Gain filter. Definite like and sub!

[@AllamHouse]

You may check out this other video about low volumes. kzbin.info/www/bejne/Y4PNgWZ_gKuZp68

[@drubarlow]

My church is late to the streaming game, but this channel has been SUPER helpful. *subscribed*

[@AllamHouse]

I’m glad you have found this helpful. Feel free to ask questions, I’m always in the comment section.

[@nuvoleasorpresa]

Great video mate, very informative! Do you know if it is possible to do the same routing for other outputs, let's say 3&4, instead of 15&16? I'm relatively new to this console so maybe this is a noob question :D Thanx!

[@AllamHouse]

This is a different approach that might have some better insight for you. kzbin.info/www/bejne/pn7RkpyreJpoiLs

[@nuvoleasorpresa]

@@AllamHouse thank you, I'll check that!

[@ajbeatz7406]

Hey, I followed the instructions, and when I plug in my pc it shows that the x32 is plugged in. The card shows that the main L and R are the 1 and 2 outputs. But on the pc no audio is coming through. Any solutions? Thanks.

[@AllamHouse]

Check out this short video that discusses some computer settings to check. Also, make sure you have the X-USB driver installed on the PC. Another thing to think about is that this video discusses a way to get audio that is okay if you do not have anyone in your venue, but as people return in-person you will want to have 2 mixes (house and stream). This video here walks through the setup I use every Sunday. kzbin.info/www/bejne/pn7RkpyreJpoiLs Finally, if you decide to change, this video discusses the routing needed to get it across USB. kzbin.info/www/bejne/jKmXeZ13p7mYkKs

[@ajbeatz7406]

@@AllamHouse Thanks for the info! Also, how do I install the X-USB driver?

[@AllamHouse]

Head to the Behringer website, search for X32, Go to the software portion on the right side of the webpage and then download the X-USB driver. Run the installer and you are good to go.

[@markeithbrown7824]

I did the set up, I ran the USB from the mixer to the computer, the mixer was detected but got no sound. What do i do?

[@AllamHouse]

You need to make sure you have the X-USB driver (Windows) and then you will have to change some settings in your stream software to me sure the audio driver is selected. In OBS you then have to add an audio input to your scene and select the X32 input from a drop down menu. You are on VMix which should be similar, but I’ve never used it personally.

[@auggment]

ok what happens if it's not very loud. Like I have to put 2 gain's on it with the slider maxed out.

[@AllamHouse]

This version is the most basic setup to use, but any changes you make will be reflected in your Mains as well. You might choose to run this mix to a Matrix, set the Matrix to go out the USB outputs 1 & 2, and then use the Precision Limiter to get your volume levels up.

[@CMB72031]

I guess I’m needing to know how to rout the matrix out of the usb.

[@stephengraham2496]

Thankyou Allan FANTASTIC step by step explanation I have been trying for weeks to get this to work. well done mate! don't suppose you could do a quick video on getting sending effects to the singer in their fold back wedges.

[@elypelowski5670]

Hello - I cannot figure out how to route Bus 7&8 to Card/USB output. Can you show how Bus channels can be routed to Card/USB out ?

[@AllamHouse]

Here is a video I did a while back that explains this setup. kzbin.info/www/bejne/jKmXeZ13p7mYkKs

[@danialmasih659]

Hi I followed the steps but I’m still having difficulties I have a x32 producer

[@AllamHouse]

Have you updated tour firmware for version 4.0 or newer? Have you connected the cable properly from the X-USB slot to your computer? If you are on a Windows computer, have you downloaded the X-USB driver? These are the places I would start.

[@AndrewGreenspanMusic]

Hey, I tried this many times - followed your steps but I am not getting any meters showing through my BS 15/ 16. I don't know if i am supposed to keep those unmuted but when i do mute/ unmute it doesnt change it. The only sound that does come through the X32 CARD is channels input 15=16 that are from my TV. I can mute them, or lower the faders but that doesnt change the same sound continuing to come out of the X32 Card. The only way to change the volume of the sound coming through the card on that channel is to lower the Preamp dial. Other then that, all my other IN's/ are not coming through the X32 Card, such as the Mac on my other two AUX in's & other instruments plugged into the mixer. What am I missing? I really appreciate your support !

[@AllamHouse]

Based on your request it sounds like you are trying to do something different than what this video calls for specifically. Are you looking to build a broadcast mix to get out of your console to a streaming / recording device? Are you interested in multitrack recording out of the console? Help me better understand your end goal and I can point you to the right setup to use.

[@petercheng1229]

Hi Eric. Great tutorial. How about sending audio to Behringer X32? Thanks.

[@AllamHouse]

If you need to get audio into the console from a computer it will usually come across USB in 1/2. This can be routed to AUX In faders or to the other standard channels if desired. You will need to use the Routing > User In settings to build some custom mapping or on the Routing > Input screen you can use the AUX In remap for a quick check. I talk about a similar setup for Zoom in this video here. kzbin.info/www/bejne/qXSUk5qkdtuApdksi=INaQ-tKwovNTijyW

[@wdewetzlar]

Awesome Video, helped me a lot. Thank you :)

[@AllamHouse]

Thanks for the encouragement.

[@GOEC316]

Hi Dave, why my OBS pick up vocal from talkback mic? Any idea and solution please?

[@AllamHouse]

The talkback mic is either routed to your broadcast mix or your house and you just can't hear it in the room (depending on how your setup is designed). 1) Are you using the talkback input on the back of the console or a different input and treating it as a talkback mic? 2) What signal are you sending to OBS? A copy of your house mix like this video explains or are you sending a MixBUS setup?

[@goosehankins824]

So all I would need is a USB 2.0 to a USB cable. Nothing is dealing with 48 volt right?

[@AllamHouse]

That is correct. This short talks about the needed cable. kzbin.infoEwWBYPgSXwE?si=WwwoDBL8_Ke_DHdr

[@MinSweeting]

after a whole year, I can finally take out the irig!!! I basically mirrored the bus I was using for the stream and its working perfectly so far

[@AllamHouse]

That’s sounds like a big step. Here is another video that might help you further refine your stream audio and settings. kzbin.info/www/bejne/pn7RkpyreJpoiLs

[@presbyterianchurchoftheres5392]

Hi- I am still using this simplistic way to stream. However, my user out no longer stays patched..... What has happened?! Any tips? Am I not saving it somehow? Must I watch and learn the more complicated ways to livestream? 😒and thank you for everything you continue to do!

[@AllamHouse]

The scenes have "Scene Safes" that allow the specific item selected (or deselected in this situation) to not be overwritten or changed by a scene change. Go to your scenes and look on the right side to see if anything is not selected in the scene safes area. I do recommend looking at enhancing your stream mix by setting up a Post Fader MixBUS setup. This gives you the ability to alter your stream mix to better benefit the listener that is not in your room. Here is a video that walks through this process. kzbin.info/www/bejne/pn7RkpyreJpoiLs

[@petercheng1229]

Great tutorial video. Will definitely give it a try. How about USB input from the computer to the X32

[@AllamHouse]

I’m glad you found the video helpful. While this is a quick, easy way to get audio to a live stream you don’t have separate control over the mix for the house and stream or the volume output. I prefer to run a Post Fader MixBUS which you can find descriptions of in these two videos. The first is more about the routing to get it out USB and the second is a full walk through of how to refine your mix for the stream. Routing Setup: kzbin.info/www/bejne/jKmXeZ13p7mYkKs Refine Mix: kzbin.info/www/bejne/pn7RkpyreJpoiLs

[@MrObrently]

If I want to phyically change an input on the back of the board, can I move the settings to the other input? Say move a microphone from input 13 to input 8. Can I just copy the settings from 13 over to 8?

[@AllamHouse]

Yes. Using the library is the easiest way to get this done. In your example I would select channel 13, click library next to the screen, scroll to the very bottom (around 90-99) and click the save button. You can enter a name and then all the settings for channel 13 will be saved in this slot. Now you can select channel 8, click library, scroll to the saved settings and click the load button. This will load the settings to that channel.

[@estercurrie4706]

Hello i ran accross your channel and would like to get help on the following. I have the x32, a Mac and an atem mini that I am trying to connect properly. Currently my church has no band. We are running tracks in house and for our live streaming. Can you guide me so that I properly connect my board using the Mac, the atem mini along with Propresenter 7 for everything. If sound should be on separate mix (live stream and in house) please provide guidance. Thank you in advance. This equipment was donated and we cannot afford the sound techs right now

[@AllamHouse]

This response has a few different parts included as well as some assumptions I am making. I am assuming your console is being used to support an in-person experience as well as a live stream experience. I am also assuming that ProPresenter will be the final hardware unit that sends your mix out to the internet for livestream. With these things covered, Here are the things you need to know. As always, if you need one-on-one help, you can fill out the contact card on my website at Sound.AllamHouse.com. 1) Build a MixBUS mix for your Livestream. Having a second mix for people that are not in your room is a much better experience for your live stream listeners. This video here walks through the setup on the console. I still use this in my weekly church services for our livestream. kzbin.info/www/bejne/d3uufIaEltqXjtU 2) Send Your Mix to the ATEM Once you have built your mix, you want to send your mix to the ATEM Mini. This video walks through the three ways to get your mix out of the console. kzbin.info/www/bejne/rnjXYq1rfpyVorM 3) Send Your Stream to ProPresenter Once you have everything built in the console and the ATEM you want to connect your ATEM to your ProPresenter machine. Go into Preferences > Inputs and you can select the Blackmagic device as a Video Input. You can also make an Audio Input and select the Blackmagic device there. Once in ProPresenter you can follow their normal steps to get the stream out to your virtual locations.

[@hellofx]

I don't recommend this kind of setting at all . . . . avoiding using USB output for live streaming just get a budget audio interface then you're good to go.

[@AllamHouse]

Keep in mind when this video was published… during the 2020 pandemic when there was no one in our venues and people needed a quick way to get audio to broadcast. I’m glad you found the video helpful. While this is a quick, easy way to get audio to a live stream you don’t have separate control over the mix for the house and stream or the volume output. I prefer to run a Post Fader MixBUS which you can find descriptions of in these two videos. The first is more about the routing to get it out USB and the second is a full walk through of how to refine your mix for the stream. Routing Setup: kzbin.info/www/bejne/rnjXYq1rfpyVorM Refine Mix: kzbin.info/www/bejne/pn7RkpyreJpoiLs

[@getfitwithdeepak]

How do we increase the volume of the USB interface? My challenge is that the FOH volume is good but when the same sound goes to streaming it is very low…

[@AllamHouse]

This is a classic case of having your amp(s) volume too high for the speakers in your room causing you to have low gain structure on each input. I will link two videos below to help point you in the right direction. 1) Gain Structure - kzbin.info/www/bejne/Y4PNgWZ_gKuZp68 This video discusses setting proper gain structure for each input and then using the main fader as your overall volume adjustment until you can properly set the volumes of your speakers in the room. 2) Two Mixes - kzbin.info/www/bejne/pn7RkpyreJpoiLs The current method (the video you commented on) is a great quick fix for getting audio to a stream, you really want to create two separate mixes... one for your house and one for your stream. The linked video is the best way to craft those mixes and manage them with only one sound tech.

[@indi2174]

My zoom audio is looping back into the x32 and going back into the XUSB 1-8 in which is then projecting into OBS mic/aux setting ... so yes it is a infinity loop.. please help.

[@AllamHouse]

My assumption is that you have USB 1/2 coming back into the console and that is being sent back to your mains and creating the loop. I would check your inputs to make sure that you don’t have USB 1/2 coming back into the console anywhere. This video does explain an easy way to get music running to your stream, but it becomes less ideal when you have people in the venue. I prefer to build a mix for the house and a separate mix for your stream. Here are two videos that run through the basic setup and routing and a second video that explains how to refine a craft your stream mix (now that is it separate). 1) Setup - kzbin.info/www/bejne/jKmXeZ13p7mYkKs 2) Refine - kzbin.info/www/bejne/pn7RkpyreJpoiLs

[@RossAndersonTheOthersAreClones]

Hi Dave, interesting but I guess that this will mean my drivers for Cubase will no longer be available so I won't be able to play /record in Cubase though the X32 and out?

[@AllamHouse]

There are some options to continue using your DAW depending on what your end goals are. Here are some videos that can point you in the right direction. 1) Multitrack and Stream - kzbin.info/www/bejne/kJOZn5p6d9qUeqcsi=DGXxgfuJQMrYaYl1 2) Mix Stream on X32 - kzbin.info/www/bejne/pn7RkpyreJpoiLssi=VNsUFBk2tvic6-J2

[@craigkoen4181]

I like the video however, when I went through the steps you have shown I did not show audio coming through the xlive setting in our OBS software. In suggestions? Your help would be appreciated.

[@AllamHouse]

If you are on a Windows machine you will need to download/install the X-USB driver and then look at the settings mentioned in the video below. If you are on a Mac you will just need to check the settings in the video below. VIDEO: kzbin.info/www/bejne/rXOrqX-En8iNsNE

[@PastorTom2009]

What if I want my output to be a Bus? I'm running a XLR to our Audio Interface. Shure MVI. Help if you can??? Thanks, Tom

[@AllamHouse]

Use the console as an audio interface and get rid of the extra gear for efficiency and less potential troubleshooting. This video talks about the basic setup and routing across USB. kzbin.info/www/bejne/jKmXeZ13p7mYkKs This video is a full walk through of an advanced setup kzbin.info/www/bejne/pn7RkpyreJpoiLs

[@SoundDoctrineSoler]

How do I route my 32 channels through the sound card and be able to adjust levels going through live streams independent from front of house levels on my x32

[@AllamHouse]

I’m glad you found the video helpful. While this is a quick, easy way to get audio to a live stream you don’t have separate control over the mix for the house and stream or the volume output. I prefer to run a Post Fader MixBUS which you can find descriptions of in these two videos. The first is more about the routing to get it out USB and the second is a full walk through of how to refine your mix for the stream. Routing Setup: kzbin.info/www/bejne/jKmXeZ13p7mYkKs Refine Mix: kzbin.info/www/bejne/pn7RkpyreJpoiLs

[@Timovd]

What about audio delay? Audio is usually processed faster than video. And the sample rate? Video is usually 48kHz and not 44.1.

[@AllamHouse]

This is a very general (bare bones) way to get a mix from the console into your stream. I have other videos that offer direction on a much more refined setup, but let me answer your questions. The board moves does have very minimal latency and will get to your camera or streaming device in time with your video. Depending on your gear you may have to add a delay on the audio to have it match all of your cameras (ie: my audio is delayed by 300ms to be in between my different cameras...done at my streaming machine). You will want to change your console to run at 48kHz to match your camera sample rate.

[@voicesoffaithsouth]

Question: we run a usb from the x32 to our mac computer. Is there a particular usb cable you would recommend. We have recently had an issue that OBS is not picking up the audio from the x32.

[@AllamHouse]

I just use a standard USB A to B cable as mentioned in this video here. kzbin.info/www/bejne/e6i6c4yGnLiLrac

[@boss696]

Good Afternoon Alan.. we have a small church and we have the X32 and we are linking our X32 from aux out 1-2 to a line in input on our computer via OBS. Can we use the similar process from the video above for this process to mirror to our stream?

[@AllamHouse]

I would recommend using the X-USB output on the back of the board as I explain in this video here. kzbin.info/www/bejne/jKmXeZ13p7mYkKs

[@indianrockstrat]

How do you EQ the main audio going to OBS with this method. We use two linked channels for livestream, routing them through an audio interface before arrival in OBS.

[@AllamHouse]

While this method is quick, it was intended to be used when the board only needed to do a live stream mix (and not a house mix also). Many people now have their boards doing House and Stream and this video displays a better option that can offer you the flexibility of two mixes which includes EQ and compression features. kzbin.info/www/bejne/jKmXeZ13p7mYkKs

[@elderandrews4884]

Good day Allan. Did you select the Aux in/USB Fix Returns button first, the button on the left?

[@AllamHouse]

This video only looks at the routing needs and doesn't require any inputs or channels to be selected. To answer your question, "No" I did not select the AUX/FX layer on the left of the console in this video. Is there something specific you are needing to accomplish?

[@norwoodbaptistchurchri]

Is there a way, once this is set up, to increase the volume to the computer for streaming without increasing the volume for the live audience?

[@AllamHouse]

I’m glad you found the video helpful. While this is a quick, easy way to get audio to a live stream you don’t have separate control over the mix for the house and stream or the volume output. I prefer to run a Post Fader MixBUS which you can find descriptions of in these two videos. The first is more about the routing to get it out USB and the second is a full walk through of how to refine your mix for the stream. Routing Setup: kzbin.info/www/bejne/jKmXeZ13p7mYkKs Refine Mix: kzbin.info/www/bejne/pn7RkpyreJpoiLs

[@MrObrently]

Any link to the usb driver would be great. I’m using a Windows 10 pc.

[@AllamHouse]

Go to Behringer.com. Search for x32. Go to software and find the X-USB driver. Install, reboot, THEN connect the console with the USB cable.

[@DroidCrossFire]

Can I assign a dedicated volume knob for the output so I won't change anything on the FOH?

[@AllamHouse]

The approach mentioned in this video you commented on was a quick way to help people get stream audio when they had no one in their seats. Currently, the best approach to take for a live stream with one sound tech is the one in this video linked here. kzbin.info/www/bejne/jKmXeZ13p7mYkKs If you get that setup and want to really dial in your stream mix, check out this second video. kzbin.info/www/bejne/pn7RkpyreJpoiLs

[@mia4279]

I'd love to know how to record a single mic channel? I'm recording a full service but I only want to get one person's mic from the board, not everyone's. I'm using a USB to record straight to it.

[@AllamHouse]

The easiest way to just record is to put a thumb drive in the top area next to the screen. Hit the view button for the USB and you will get a record screen that appears. You can use the buttons (and arrows) to change what your source is that will be recorded. Then, hit the record button and when complete, hit the stop button. Wait for the little red light to go out next to the thumb drive and then you have a recorded WAV file.

[@myqueerview1987]

How would i set this up if I have 3.o on the x32 and not the 4.0? would it just be output 1&2 to grab the main 15&16 to copy into the card?

[@AllamHouse]

Honestly, the best option is to just update to the newest firmware. Save your current scene before doing so and then do the update which takes about 2 min total. It is well worth the flexibility. This link goes through the Scene Save process. kzbin.info/www/bejne/fWHFoombq86Fgck Also, this video covered a very basic way of getting audio to a stream, it is not ideal for a long-term solution. The method I recommend is using a Post-Fader MixBUS setup which gives you the ability to customize the mix for your stream (if desired). This also gives you more flexibility if you do NOT upgrade software if you do this on MixBUS 1+2. kzbin.info/www/bejne/jKmXeZ13p7mYkKs

[@wimusiquell]

I have my laptop hooked up and my outputs are my Behringer X32. I have my headphones connected to my mixer as well, and I even have Spotify playing and I don't hear anything through the headphones. Nothing from my laptop is being heard, even though the levels and outputs are properly picked. Is there a setting I have to change on my mixer in order to hear everything from my laptop through the mixer, and headphones ?

[@AllamHouse]

It sounds like you are trying to send audio from your computer into the mixer… I’m assuming across USB. If this is the case then you need to… (1) adjust the sound on your computer to use X-USB as the audio card (2) setup user inputs that include USB 1/2 as inputs. (3) route those two channels to whatever faders you want them to appear on. This is more commonly used in a Zoom meeting environment where you want to have audio come back into the board across USB. I talk about that setup in this video here. kzbin.info/www/bejne/qXSUk5qkdtuApdk

[@johncarlosvelazquez8721]

Pls save your settings on to a USB before you update it because it will delete everything it will be like a factory reset I know because it happened to me pls save it to a USB before you update

[@AllamHouse]

Yes. I have that as the top pinned comment and in the description. I’m sorry you experienced that.

[@kelseychiyangi5454]

Are you able to do a video showing what to expect on the pages below the screen when you're using an atem and studio mode in OBS

[@AllamHouse]

So you are talking about an OBS video if I understand correctly. I will say there has been an update to OBS not too long ago which now provides more input options from the 32 USB channels coming from the console. I haven’t used these new features, but it does provide some different setting options than what I have used in the past. I’ll see about making a video about OBS.

[@donaldburns4462]

I have my live stream out to bus 9/10 but it sounds really tinny. Too much high end but when I listen to it by soloing the bus 9/10 it sounds great. What is happening

[@AllamHouse]

While this setup is the fastest way to get some sound into your livestream, you want to keep in mind that the mix you are sending is really intended for your room. You will want to explore building a different mix for your stream to make up for the differences in your room mix vs. stream. This video here is the way I run my church mix and it has proven to be very manageable and only requires one sound engineer. kzbin.info/www/bejne/pn7RkpyreJpoiLs

[@kparkka]

Thank you very much. So simple, but hard to figure out by my self. I hope you make a video for that matrix version and the routing for iem monitoring as well.

[@mrmiltonf299]

How do I add compressions and other filters to my livestream through the USB? Or shall I say how do I put send my u s b stream to a bus

[@AllamHouse]

m glad you found the video helpful. While this is a quick, easy way to get audio to a live stream you don’t have separate control over the mix for the house and stream or the volume output. I prefer to run a Post Fader MixBUS which you can find descriptions of in these two videos. The first is more about the routing to get it out USB and the second is a full walk through of how to refine your mix for the stream. Routing Setup: kzbin.info/www/bejne/jKmXeZ13p7mYkKs Refine Mix: kzbin.info/www/bejne/pn7RkpyreJpoiLs

[@MTBMichigan]

Thanks. Just learning all of this stuff. I am sure this is a dumb question, but do you show the hardware side of the process in any videos? I am just not sure how you are connecting from the board to the computer.

[@MTBMichigan]

Never mind. I was thinking there might be a different connection than the main connection.

[@AllamHouse]

Here are two videos that might help you out. 1) connections: kzbin.info/www/bejne/rnjXYq1rfpyVorM Regardless of your mix, you have to select how you get the mix out of the console and to the world. This video talks about the three different methods for your setup. 2) Refining a Mix: kzbin.info/www/bejne/pn7RkpyreJpoiLs The video you commented on is a quick way to get started, but having two mixes is more ideal… one for your house and one for everywhere else. This video presupposes that your house mix is fine and I walk you through refining your stream mix

[@dwightshumate8709]

I'm trying to do this using X32 Edit. Is there a tutorial for that interface? Or do I have to use the interface on the device? Thanks

[@AllamHouse]

X32 edit can do everything the console can do, it it is a slightly different layout. I have a few videos that include X32 edit, but many of my videos are shot on the actual console itself. Although I don’t recommend using this setup (explained in this video) as a long term solution, it is quick. I will make a video of this on X32 Edit in the next 24 hours and post it for you since it’s too many steps to type here. Make sure you are subscribed so you know when it comes out.

[@CarlosOrtiz-wv8pw]

Hello ,Thanks for the video. Can you plug in straight to a phone to stream?

[@AllamHouse]

Ideally you would go with a USB connection into your device or send from the board into a camera or switching device. If you need to go directly into a phone people typically use an iRig converter. Keep in mind that these are designed to control the energy of a mic or maybe a guitar, but you will be sending a full range, mixed signal into it. If you push too much volume into these they will distort pretty quick.

[@YourHaloCreations]

How would you access the full 48 inputs? Looks like you can not on the console itself, but can you make use it of them somehow?

[@AllamHouse]

The console really only offers 38 inputs (32+AUX). This video is an overview of the routing screen that might be helpful. kzbin.info/www/bejne/hqHIooWrhaycaLs

[@upwardsjarrellYT]

Hey so we have a designated Livestream MixBus. Would we do the same thing but only for one output and not 2 as described in the video?

[@AllamHouse]

If you plan to run your audio across USB, this video here gives you the exact process for using a MixBUS setup. I do recommend making a stereo pair for your live stream as a stereo signal is more desirable for your listeners. kzbin.info/www/bejne/jKmXeZ13p7mYkKs

[@upwardsjarrellYT]

@@AllamHouse Ok thank you so much! We will look into it.

[@liamdonaldson6449]

Great explanation for the version 4 mixer. Clarified a few points for me.

[@StJohnsLutheranKnoxvilleTN]

Does the mixer itself have to be connected to the internet for the update? I'm a newbie with this board ...

[@AllamHouse]

No. You will load the file onto a thumb drive and then follow the process to do the update. If you have settings of any type, make sure to save your scene BEFORE you update the firmware. This video talks about saving scenes. kzbin.info/www/bejne/fWHFoombq86Fgck

[@impurfekt]

Thank you so much for this! Having been looking high and low to figure this out. Live saver!

[@ais68462]

What if audio is choppy ? Any ideas? It was working fine then all of sudden audio cutting in and out

[@AllamHouse]

I would start looking at your Sample Rate. Many times for audio only it would be 44.1khz, but for live stream (syncing with video) needs to be 48.0khz. Another possibility might be your audio clipping and peaking. If that is the case, you would want to put a limiter in place to control the audio output levels.

[@DMTalesTTRPG]

I set it up, but I am getting almost zero volume out to OBS. Do you have any hints on how I can increase the output volume?

[@AllamHouse]

I’m glad you found the video helpful. The low volume is usually based on improper gain structure which is usually a result of an issue with your system tuning. This video here discusses these common challenges. kzbin.info/www/bejne/Y4PNgWZ_gKuZp68 While this is a quick, easy way to get audio to a live stream you don’t have separate control over the mix for the house and stream or the volume output. I prefer to run a Post Fader MixBUS which you can find descriptions of in these two videos. The first is more about the routing to get it out USB and the second is a full walk through of how to refine your mix for the stream. Routing Setup: kzbin.info/www/bejne/jKmXeZ13p7mYkKs Refine Mix: kzbin.info/www/bejne/pn7RkpyreJpoiLs

[@DMTalesTTRPG]

@@AllamHouse gain was the issue. The powered speakers were MAXED so pushing anything from the board impossible.

[@justhim8745]

Right now we have 3.11 How to set up for streaming

[@feoysabroso]

I was trying to find that info since covid started, I streamed live music with mi brother using OBS and noticed I only get whats connected to IN 1 and 2, pre fader, I was trying to get to stream the mix, effects and all, but wasnt able to, until I found this video, Thank you so much! Ill try it soon

[@AllamHouse]

There are a few other newer videos on my channel that walk though using a Matrix to have different volume levels for your house mix and stream as well as running an AUX mix for your stream.

[@jwillbassist]

Is it possible send the main outs to USB and Multitrack at the same time?

[@AllamHouse]

Yes. This video walks you through the setup and things to consider along the way. I use a different MixBUS for my livestream, but you could certainly use your mains if that's your approach. kzbin.info/www/bejne/kJOZn5p6d9qUeqc

[@thorobreadd76tracks]

How can we do a mirror of the main output to an aux like to stream to an irig that has stereo quarter inch inputs

[@AllamHouse]

This is the best option. Also, if you can bypass using an iRig you will be better off. They really aren’t designed to handle this signal level and they tend to distort. kzbin.info/www/bejne/jKmXeZ13p7mYkKs

[@Dannyvm27]

Will this work with the x32 producer?

[@AllamHouse]

Yes. The inside of the console is the same, the producer just has less faders.

[@phoenixkfy]

Can I listen to USB recordings in the iPad?

[@AllamHouse]

I’m not quite sure what you mean with this question. If you are using an iPad to remotely control the console, you can only control... there is no sound that comes back to the iPad.

[@TheRobertCostello]

Will this mess up the output 1 and 2 on the AES50?

[@AllamHouse]

No, this will have no impact on your AES50 network.

[@johnny728100]

I didn't save my scene. How do I get it back?

[@AllamHouse]

I'm sorry to say that if you do not have your scenes saved, there is no restore feature to get your settings back. It is an opportunity to rebuild your scene, but I know that is not the answer you are looking to hear. I did just put out a video on saving scenes in case that helps going forward. kzbin.info/www/bejne/fWHFoombq86Fgck

[@princeakorsah4066]

Hello Dave, thanks for info, My Church has a X32, I have installed the driver and Firmware on my computer, but I can’t hear any other channels on my streaming recording except channels 1 & 2, I used channel 1-22, but after recording through the streaming online, only channels 1-2 is playing back, can you please help. Thanks 🙏

[@AllamHouse]

So, this video discusses how to quickly copy your house mix and send it across USB into streaming software. This method is an okay start, but if you have people in your room as well (live audience) you will want to craft two mixes… 1 for the house and 1 for the stream. I personally use a Post Fader MixBUS setup which allows me to only need one sound tech to mix both mixes. Here are two videos to guide you. If you need to do a virtual consultation, I do handle those outside of KZbin. Just fill out the contact card on my website to start the conversation. sound.AllamHouse.com Recommended Videos: 1) Routing: kzbin.info/www/bejne/jKmXeZ13p7mYkKs 2) Craft the Mix: kzbin.info/www/bejne/pn7RkpyreJpoiLs

[@princeakorsah4066]

@@AllamHouse thanks so much, I really appreciate your reply and helping me out. God blessed 😇 you. 🙏🙏🙏

[@dub369]

very good. i subscribed to your channel and now i will watch all the videos. I just bought the x32 producer. There are some things I can't understand how it works. I will look for them in your videos. I would like to know if I can contact you to ask you for information about it. Maybe with a donation so you don't waste your time rightly. I use it with mac, and ableton live plus synth. A hug and w music. !!!

[@AllamHouse]

The Producer is an interesting console since it doesn't have the scribble strips. If I have to use the producer I tend to bring a laptop or two iPads with me to know what channels I am working on and tend to only use the faders on the console during my initial setup. If you want to setup a one-on-one session, please fill out the contact card on my website at sound.allamhouse.com and we can get something setup for you.

[@dub369]

@@AllamHouse no thank you. I already understand how to do some things. It’s a lovely mixer 😂

[@testlive7952]

Is it impossible to do livestream or connect with OBS without apdating firmware? The current firmware is now 4.06?

[@AllamHouse]

As long as you are on firmware V4.0 or newer you are fine. When I made this video, most people were still on V3. This video talks about the best way to start sending your stream into OBS. kzbin.info/www/bejne/jKmXeZ13p7mYkKs

[@testlive7952]

@@AllamHouse Thank you! Why I questioned this,is because the mixer I always use belongs to my school,so maybe I can’t update it. Thank you for your polite answer!

[@reignahoyt38]

Does this separate the EQ/Compression/Gating from the house mix to live streaming by chance?

[@AllamHouse]

It does not, in fact the X32 (along with most other consoles) only offer the ability to EQ/Comp an input one time on their channel strip. You would then build your various mixes using those sounds and then you have a channel strip for your mix , but not for the individual input per mix. In terms of this video, while it is a quick, easy way to get audio to a live stream you don’t have separate control over the mix for the house and stream or the volume output. I prefer to run a Post Fader MixBUS which you can find descriptions of in these two videos. The first is more about the routing to get it out USB and the second is a full walk through of how to refine your mix for the stream. Routing Setup: kzbin.info/www/bejne/jKmXeZ13p7mYkKs Refine Mix: kzbin.info/www/bejne/pn7RkpyreJpoiLs

[@reignahoyt38]

@@AllamHouse Thank you so much! I really appreciate your feedback and explaining it for me(:

[@Rolandonbass]

hey Mr, i want to ask, i want to send all dry signal from console to PC, then i mix it on DAW (live), i insert comp, eq, etc on DAW, then i sent out signal from DAW, live, to OBS or other live streaming software. Can i do that ? what equipment do i need ? bcause i dont like the sound from console, i've tried to mix them on FOH mix and separate stereo mixbus 11+12, but i dont like the sound thx for the info

[@AllamHouse]

Yes you can. This video here walks you through the routing needs. It is easiest to send your audio into a video switcher or a camera from the console (at the end) since you are already using the USB to connect to your DAW. kzbin.info/www/bejne/gaG9oaaFlNFnh9U

[@Rolandonbass]

@@AllamHouse yess, i already watched it, thank u so much sir.. i’ll try it.. regards from indonesia 🙏🏼

[@ofthewayministries]

Thank you, this is extremely helpful. We've been trying to get the x32 Compact to be recognized on our PC, and it hasn't been able to recognize it. We currently have channels 7-8 as our main output to the house. Would I set the user outputs to mirror 7-8 or still use 15-16? We followed this step-by-step, but our desktop doesn't recognize the USB output... Even in OBS, it doesn't recognize an X-USB or any external audio source. Any help is greatly appreciated. Thanks.

[@AllamHouse]

Couple things. (1) Make sure you have the X-USB driver installed (if it’s a Windows machine) (2) if you still have trouble it might be some security settings which I discuss in this video kzbin.info/www/bejne/rXOrqX-En8iNsNE (3) If you are running a house mix and stream from the same console, you might want to use this setup for more flexibility. kzbin.info/www/bejne/pn7RkpyreJpoiLs

[@ofthewayministries]

@@AllamHouseI'm not very familiar with PC machines. Where/How would I go about downloading/installing X-USB driver(s)? Thanks.

[@AllamHouse]

You’ll need to go to the Behringer (Music Tribe) website, go to the X32 page and navigate to the downloads area. There you will find the X-USB driver that you can download and install.

[@cancholajared1163]

Can I use something other than a USB?

[@AllamHouse]

Yes, you can choose USB, AUX Outs (1/4” or RCA) and XLR. These are the options available. The question is what type of connection is on the recording end of this signal? Also, there are some better options for building a stream mix of you have people in the seats now. This video is the most widely used currently, and what my church uses every week. kzbin.info/www/bejne/pn7RkpyreJpoiLs

[@AadilKhan-lm4gp]

Hello AllamHouse, thank you for the video it was most helpful. I followed your directions and it does seems to be getting the signal in OBS however, when i do a test recording, i still dont hear anything during playback. I ensured the mic is set to behringer x-usb, the guage even moves in OBS if i speak but playback doesnt pick up anything. Is there something I'm missing. Thanks in advance for your support

[@AllamHouse]

What do you mean when you say ‘playback’. Are you recording in OBS and then trying to watch the movie back or are you trying to do a playback through the X32?

[@AadilKhan-lm4gp]

@@AllamHouse i did some more testing and the issue really is when I play back a video recording, the audio from the mikes and instruments are extremely low. I turned up the volume of the audio input in OBS to the max but it doesnt seem to make a difference. Anything I can try ?

[@AllamHouse]

This is a common issue and I would recommend checking out this video that discusses gain settings being the usually challenge to solve. kzbin.info/www/bejne/Y4PNgWZ_gKuZp68

[@AadilKhan-lm4gp]

@@AllamHouse this has been very helpful, I saw another chat where someone suggested to add a gain filter to OBS audio input and that actually worked, but getting some clipping, I think I will try following your matrix guide for the live stream instead of the basic mirror and use the suggestions in your link. Thanks man, you have been a true blessing to my church : )

[@AllamHouse]

Yes, in OBS you can use a gain filter, but you also want to add a limiter to keep it at -3. OBS will distort of you push it above that level (in my experience)

[@derrickwoo1881]

Have tried but no mic signal received using usb cable. But when changed to use audio aux cable thru phone jack, there is mic signal comes in and there is mic output sound while streaming. May I know what problems actually happen using the USB cable? Is it the card problem? And is the output quality of using aux cable same with using the USB cable in terms of mirroring mix to streaming? Or using USB cable will be better sound quality?

[@AllamHouse]

This is usually an audio setting on the computer. If you are on Windows you need to go to Settings>Microphone and allow apps to connect to the mic. If you are on MAC go to Preferences>Security>Microphone and then check the Privacy tab.

[@derrickwoo1881]

@@AllamHouse can have your email address so that I send some pc setting pictures to you for checking? Thanks.

[@goodarguments]

Question: I followed all your steps, except I sent a copy of a mixbus (one mono channel) with my separate mix for our livestream. However, after I selected the x-usb input in OBS, I am not seeing the green audio bar lighting up when I send audio to it. I didn't actually try a livestream to see if sound was in fact coming through because I assume that if the sound input bar is not lighting up then nothing is coming through. And the mixbus was definitely not muted! Help please...

[@AllamHouse]

Here is the first place I will point you. Let me know if you still run into issues. kzbin.info/www/bejne/rXOrqX-En8iNsNE

[@goodarguments]

@@AllamHouse The permissions were there but still no sound. Do I need to install a driver maybe?

[@Jjoonaass]

Hi! Question for you! What cable did you use and where did you plug in the back? I currently have an RCA to Auxiliary. Is that even the cable I need for this or no?

[@AllamHouse]

I use an USB A-B cable. kzbin.infoEwWBYPgSXwE?feature=share

[@Jjoonaass]

@@AllamHouse you at the best for replying! This is last minute preparations for Easter! Thank you!

[@Stameboat]

Have an odd problem. I did this and my mac picked it up just fine and called it something like X-32 when I tied it into OBS, using a PC it didnt really recognize it. It sees it as a microphone but OBS wont pick it up, but I can tie the stream to the computer speaker output just fine and then stream using that audio. Any ideas? I had to jack the audio level way up to get it loud enough.

[@AllamHouse]

Here are a few things for you. On Windows, make sure you have the X-USB driver installed to allow the console to speak to the PC. You also might need to go into the security settings to allow the computer access to the ‘microphone’ of the console. PC security Video: kzbin.info/www/bejne/rXOrqX-En8iNsNE For the low volume, you will want to make sure your gain is set right to start with. Here is a video that discusses that information. kzbin.info/www/bejne/Y4PNgWZ_gKuZp68

[@Stameboat]

@@AllamHouse aha! Thank you. I didn’t realize their was a driver to install on the PC. Thanks for the quick response. I’m hoping the volume problem is just because of how I was capturing it, on my Mac it was more than sufficient.

[@kevinstorey6021]

Question…will this work for sending my logic mix to livestream and house?

[@AllamHouse]

If you are running a live event, I would be cautious about sending a DAW mix to your live audience. Typically, the USB connection adds too much latency and in smaller venues it is very noticeable. This video here talks about sending your inputs to the DAW, building a mix and then sending that mix back to the console. This might be the route you try and see if it gets you close to your goals. kzbin.info/www/bejne/gaG9oaaFlNFnh9U

[@kevinstorey6021]

@@AllamHouse perfect…thanks for linking that video as well

[@GaryPozner]

You are my Hero🙏🙏🙏🎹🎹🎹🙏🙏🙏

[@AllamHouse]

I’m glad you found it helpful. Let me know if you have other questions.

[@ElsonA9]

thank you finally i solved whole bunch problem from your video thanks and god bless

[@TubeLamba]

Exactly what I was looking for... THX!

[@soundbooth2389]

what if I am not using 15-16 as my main L-R but instead I am using the monitor outs because I prefer the 1/4in cable connections in my main speakers. It doesn't seem to be the same process as the monitor L-R isn't an option in all the menus.

[@AllamHouse]

Monitor outs on the top right of the console (with a volume knob) have a much different functionality. If you want 1/4” outs you would be better served to go to Routing > AUX Out and select AUX Out 5&6 for your mains. Then connect your 1/4” outputs to the back of the console.

[@soundbooth2389]

Thank you. I will work with this!

[@bryanperez9414]

I have a question I use sling studio for my live stream and take my audio out from my x-32 to the streaming hub. The only way I can get stereo is from the headphone jack is there any other way to get a stereo out for live steam so I can send different mix to the live sound? Thank you

[@AllamHouse]

This. Idea will show you how to setup two different mixes with one sound tech. Once you have your mix setup on your paired Bus, then go to Routing>AUX out and route them out AUX out 5/6. This allows you to use a 1/4” to 1/8” TRS cable to connect from the back of the console into your Sling Studio. kzbin.info/www/bejne/pn7RkpyreJpoiLs

[@bryanperez9414]

@@AllamHouse got it thank you!

[@oncebadseed]

Thank you, Thank you... You just saved me from big headache! I'm definitely subscribing

[@AllamHouse]

I’m glad you found this. Idea helpful. I will say that this is an okay option if you do not have people in your venue, but most people are mixing for both house and stream now. If that is the case you want to go a different route for your setup to allow for a mix for your house and a dedicated mix for your stream. This video walks through the routing of it kzbin.info/www/bejne/jKmXeZ13p7mYkKs This video walks through an advanced mix that you can build using this Post Fader MixBUS. kzbin.info/www/bejne/pn7RkpyreJpoiLs

[@VineyardInnsbruck]

Question about connection x32 to streaming PC... vMix.. I understand that it is with USB. We have a challenge with the distance x32 and the Streaming PC.. 8 Meters... Is it possible to use the LAN on the x32 in order to get the sound from Mixer to StreamPC / vMix???

[@AllamHouse]

While USB is a great option, you will be pushing the limits at 8 meters (25 feet). The two ways to do this well are (1) route your stream out some XLR outs on the back of the console, run XLRs to your computer and get a 2 channel audio interface to convert the signal to USB and into your computer. This is bot ideal, but you can get it done for about $150. (2) get a Dante card for your X32 and connect the x32 and computer to the same network to transfer the signals. This is the ideal scenario, but will come at a higher cost.

[@mikerickyfenelon4493]

Do you know any apps I can use to transmit what sound I want in my live

[@AllamHouse]

I'm not quite sure I understand your question and since there are so many possibilities, I'll ask you to ask it again but slightly rephrased. Are you asking about changing the actual sound coming out of the console? Are you referring to a computer program to send your live stream audio into and stream it (with video) out to the world?

[@mikerickyfenelon4493]

Do you know an virtual studio that I can use so that I can control the sound in the live stream

[@testlive7952]

If I update the firmware,the library and the scenes will not be deleted?

[@AllamHouse]

Updating the firmware will NOT delete the scenes stored on the console.

[@testlive7952]

@@AllamHouse Thank you! I will update my console!

[@TheDJroombaGaming]

I have my x32 routed the same way you have it here except that mine comes out the USB 2.0 on the back directly into a USB 3.0 input on a USB-C hub for my iPad Pro into Switcher Studio. My iPad accepts the x32 as audio input but also thinks that it should be the default output. This doesn't matter for internet livestreaming but it's a huge problem when I'm trying to broadcast over an HDMI hub as well. I've been told that it doesn't matter what the x32 says but I cannot find anything on the internet about my problem. Switcher Studio's audio output doesn't change regardless of whether i plug in the hdmi first or the USB audio from my sound board. I'm so confused...

[@AllamHouse]

This is a rather unique setup and I will start by saying I have never used Switcher Studio. I know it is a robust streaming platform, but I have not interacted with it in person. Usually, when you plug in the USB connection from the X-USB slot on the back of the console to a machine it will (by default) use USB 1/2 as an input from the console and then also have USB 1/2 as an output form the device back to the console. This would allow you to play audio across USB from the device back into the console. This is well and good in an isolated setup, but it sounds like you are now trying to take this entire setup of audio from the console, connecting to video in Switcher, and then send it out HDMI to other destinations. If this is all correct, I would start by looking in the physical settings of the device. When you plug an HDMI cable into a laptop the audio will default to go OUT across the HDMI cable... which is your desired situation. I believe there will be a "magical" combination of device I/O and Switcher I/O settings that can get you to the desired outcome. I wish I have more direction to offer, but again I have limited knowledge of Switcher.

[@scottwallace3967]

Trying to figure out if I can use headphones on the soundboard so I can hear what is going out to the stream.

[@AllamHouse]

This setup just takes your main mix and sends it out USB 1/2 to go to your streaming device. To solo it in headphones you would just click the solo button over your main fader and it will be heard in your headphones. Note: By default the main mix is what is heard in the headphones if nothing has the solo button pushed. So really, you don’t need to push anything, but the solo button over the main fader might make you feel better to know you have the right thing in your headphones.

[@scottwallace3967]

@@AllamHouse Really good information. Will try. Thank you.

[@livingwordfcf1765]

I got it setup but How do i output on OBS?

[@AllamHouse]

I don't understand what you are asking exactly. Did you get the soundboard routing handled? Did you connect the cable from the X-USB slot on the console to your computer? If on Windows, Have you downloaded the U-USB driver (not needed for MAC) Have you added the audio input source into OBS?

[@howardhelms4877]

Followed direction but my OBS is not picking up Xusb I have IN 1-2 usb behringer up thru 7-8 It seems to pick up on my own laptop but not on my streaming computer Windows 10

[@AllamHouse]

If you are on a Mac (personal) it will automatically recognize, but a Windows machine will need the X-USB driver downloaded and installed. You can find it at the Behringer website, search for X32 and then scroll down to the "Software" section on the right side. I am currently using the 4.59 version.

[@howardhelms4877]

@@AllamHouse Thank you, I'll check that out.

[@howardhelms4877]

We got it. Now to see if we can split the feed so we can control audio to OBS. Thank you 😊

[@adeyemi-bisilekoadetoyese3686]

Hello,thanks for this video.Pls could you do a video on how to use the X32 berhinger with Audition to record a multi track & also specify the right driver to download from the berhinger website.I use a Windows PC.Thanks a lot.

[@AllamHouse]

I’ve never used Audition, but there should be some KZbin material about that DAW. The driver you need for a Windows computer is the X-USB driver from the Behringer website. They continue to add new versions to keep up with Windows updates. This video here discusses the basics of multitrack recording. kzbin.info/www/bejne/pYHVkpqQlN1qg7M

[@livingconnectionchurchigle5289]

Can I use this USB output as an input for my iPhone 7 (using a Apple Lightning to USB3 Camera Adapter) and then use Facebook Livestream? Will the iPhone and Facebook recognize this external audio input?

[@AllamHouse]

I have not tried this same setup so I can’t say for sure. Here are some things I do know: 1) Some people are using dongles to convert to USB-C and run into new iPads (or iPhones) to stream through Switcher Studio. You might check out some of the Switcher Studio videos to see how they are making it work. 2) It sounds like you are trying to use minimal equipment, but you can always run a laptop with OBS (free software) and stream to FB, YT or other platforms. We use this at my church and it works great. You would plug your phone into the laptop as a camera and then run the audio from the console through USB into the laptop.

[@andywinford2770]

Great video. We use an ATEM Mini and just upgraded our old console that was dying to an X32. I'm getting a crash course as the only 'IT' guy in church. We were going from a single 1/4 jack to a 1/8 jack to the ATEM. How could I mirror this setup with X32?

[@AllamHouse]

Instead of routing the Stream output to USB 1&2, you can send it to AUX 1&2 (output) in the Routing>AUX section. Then, connect a 1/4” to 1/8” TRS cable and this will give you a stereo signal to connect to the ATEM.