Someone here asked: "How much solder do I use?" Until you get a true "feel" for soldering I'd recommend this - use about 1/2 of the diameter of whatever fitting you are soldering. Thus if you are soldering 1/2" pipe, use about 1/4" of solder. If you are soldering a 1" pipe - use about 1/2" of solder. And how do you know how much solder you are actually using? Well, if you need 1/2" of solder, bend a 90 degree angle at the tip or your solder so you physically have 1/2" of solder after your bend. If you need 1/4" of solder, bend the tip of the solder so that you have 1/4" of solder past the bend. It is VERY easy to add too much solder (and as this video showed) where you end up puddling the solder inside the joint. Truly, you need VERY LITTLE solder to make a sealed joint. When I was a novice I was installing a boiler and had soldered a 3/4" vertically mounted gate valve - and because of the mass of the valve I REALLY soldered that valve to make sure it didn't leak. Problem was - I had used so much solder that when the valve was opened (the gate was pulled back to open the valve) I had completely sealed the valve closed. I had created a solid solder plug! Yup - played hell finding that little error when the system wouldn't work. And that's when boss-man taught me the 1/2 the diameter of the pipe trick.
@chanfongleong27674 жыл бұрын
7
@rogertycholiz22184 жыл бұрын
@@kevinr4454 Just get away from soldering! Use only compression fittings. They are easy to install and never leak.
@normabrambila4373 жыл бұрын
Do you have videos on the sewer line that connects to city main? Thanks
@irishmike49143 жыл бұрын
Why use an auto cutter you'll need your trusty rigids reamer anyway. Always ream! Lol
@rpan5441 Жыл бұрын
After watching your video, I assisted my neighbor in installing the water heater. Following your technique, the results were amazing. My neighbor thanked me for a professional result. In fact, I convey my thanks to you, because you deserve the credit.
@Got2Learn Жыл бұрын
Wow, I feel honored, thank you so much for the feedback!
@danbuffington755 жыл бұрын
The quality of the preparation for these videos is insane. Legit, one of the singular most detailed KZbinrs.
@Got2Learn5 жыл бұрын
This channel needs more subscribers like you ;)
@russscott86503 жыл бұрын
Yeah "detailed" until you pay for shit that is a giant waste of time.
@Vanilla_Icecream12313 жыл бұрын
@@russscott8650 ?
@georgedavall9449 Жыл бұрын
@@russscott8650 Dont be a jerk, no one likes a jerk!
@Payaso_Boxing Жыл бұрын
This video is pure gold. Once you understand the concept, it's pure gold.
@LeoRousseau3 ай бұрын
The flux chases the heat and the solder chases the flux! 😉
@TerryPullen3 жыл бұрын
A few years back my cleaning brush had gotten contaminated, it looked fine but something on it was ruining my joints. About 25% of my joints were failing and had to be re-done. After going crazy for about 3 months, one day I couldn't find my brush so I used sand paper and no failures! I was so excited to finally be free of that curse I was stopping strangers to tell them about my lousy cleaning brush.
@Got2Learn3 жыл бұрын
😆😆😆
@786qad3 жыл бұрын
Stopping strangers, made me chuckle. I know what you mean
@sergiohernendez87673 жыл бұрын
Wow what a joke tbh. I can use used sand paper or a "f" ed up brush and visibly see if the pipe isnt cleaned well. U r a joke. Find a new profession u dum fk
@richardhead82645 жыл бұрын
Call me weird, but I like to see a few millimeters of solder adjacent to the joint.
@Got2Learn5 жыл бұрын
That's fine.
@edchevalier2695 жыл бұрын
NOT weird. That's one way you know the solder has reached the back of the joint, taking into consideration you had the solder on the joint in the first place, which I believe you did.
@johncaper684 жыл бұрын
Same with glued joints. If you can see the glue you know it's glued. As an apprentice (and ONCE as a Journeyman) I forgot to glue a joint. Easy to do. Visual cues save you from digging down 3' to find out why it's not holding during the test
@kcrowe85834 жыл бұрын
Agreed. I also knock the bead off with a flux brush.
@Jlitt-yw2zm4 жыл бұрын
Exactly. Or “degree of certainty”
@stevie5020094 жыл бұрын
I really like the tinning flux because as you are heating the joint, the ground up solder in the flux starts to plate out when you are at temperature. This helps me a ton because it is a signal to me that I I can start applying the solder and moderate application of heat to minimize the potential for overheating the joint. The other thing I noticed is the ground up solder in the flux really reduces joint fouling due to regular flux overheating and oxidation. great video!
@Got2Learn4 жыл бұрын
Good comment, good tips!!
@als10233 жыл бұрын
Thank you for commenting !
@timlong1462 Жыл бұрын
Would there be a situation where you should not use this flux? I can't see a reason to buy the regular stuff except the expense. For a DIY that's negligible.
@pvbarbell19043 жыл бұрын
We have a timber frame house with exposed copper piping for the fire suppression system. The plumber that did our joints did a fantastic job with just a small fillet of solder around the fittings. He went to the extra trouble to make the soldering look good because people will see his work for the life of the house.
@Got2Learn3 жыл бұрын
Niceeee!!!
@charleswilson45983 жыл бұрын
I am a diyer with no experience at soldering copper pipe, but after watching some of these videos I got together some 1/2 in pipe and tools and began practicing. After a while my joints started looking decent and I thought they wouldn't leak although I had no way to test them, but they looked filled and good. So, I learned what it takes to make a good joint. Then I hired a plumber to install a new water heater. I was particularly interested in watching him solder the copper pipes. I was really impressed. All of his joints were examples of good soldering technique. I couldn't have done what he did but I know a good joint when I see one.
@rayprisk59952 жыл бұрын
Followed your advise when soldering gas tank air pressure lines on my 1914 Oldsmobile, and your video helped me do a much better job than I've done in the past. Thanks alot.
@Got2Learn2 жыл бұрын
Glad it helped!!! :)
@mikemorgan50154 жыл бұрын
I solder with cotton gloves. A finger swipe at the end to knock off the drops and leave a clean appearance. Then a quick wipe with a damp rag to get rid of the flux. I like the look of a tiny, even fillet of solder. Key word TINY. I was taught never to rely on capillary action on a horizontal joint and trace a full 360 with the solder. When i started with my father, he recommended bending a tight 90 at the end of the solder to mark it and get just the right amount until I got a feel for it. 1/2 " copper 1/2 inch of solder, 3/4" for 3/4" etc. When the bent leg is gone, you're done. Lather rinse repeat. To speed cleaning he had drill brush attachments made up for male and female for 1/2 and 3/4 fittings. They work great. I still have them around somewhere. Don't do enough copper anymore to use them much these days. Not saying my way is THE way. Just sharing what works for me.
@charleswilson45983 жыл бұрын
As I was watching another video it occurred to me that wearing gloves might be a good idea to prevent contaminating the copper as you clean it,
@mikemorgan50153 жыл бұрын
@@charleswilson4598 The disadvantage of wearing gloves is you don't get that attractive dark staining on your skin(my body chemistry?, I know very few that get this) and that unique, I've been running copper all day smell. Ok, may not a disadvantage after all. I prefer leather for cutting and deburring, better gription. Never really thought about it before, but next time, I may wear leather on my left and cotton on my right hand. Just had my eureka moment. BTW, the gloves are the cotton poly blend yellow ones. I always thought they were just cotton, but just checked. Handy Andy gloves. They haven't changed much in 50 years.
@charleswilson45983 жыл бұрын
@@mikemorgan5015 I haven't changed much in 50 years either.
@mikepedersen10613 жыл бұрын
True…. Enough Said
@raymondjacobs84294 жыл бұрын
When cleaning joint, also lay emery flat on hard surface and drag end of fitting across emery to clean the face, solder will stick to the face of fitting to fill any voids
@sergiohernendez87673 жыл бұрын
No one ever mentions this on you tube lol. In Mexico we all do this 😂😂😂👍👍👍
@alanling93293 жыл бұрын
I like the fact there is always plenty of room in these videos unlike in reality when they are tight against a wall in hard to access places.
@bradleyrussell19733 жыл бұрын
True, but planning a route goes a long way
@danielson24543 жыл бұрын
Lol
@keggerous3 жыл бұрын
@@LeeroyPaladin And that's when the motto of, "Sometimes you gotta not be afraid to fuck someone's shit up" comes into play
@frankmontez68533 жыл бұрын
Yep. Agree 💯
@reubenha13 жыл бұрын
This is a professional showing us how to do a good job. You need to account for camera angles. If the demo pipe is too close to the wall the camera cannot get in
@ThaRipla9164 жыл бұрын
I want to thank you Sooooo much... watched many of videos for tips and tricks. Just soldered a vertical 1" copper line (Main line). 4 joints soldered... you amazing. Thank you again, came out PERFECT
@Got2Learn4 жыл бұрын
Awesome man, $$$ ;)
@johnmcginley43952 жыл бұрын
His video is good & makes sense, 3 things I also do which I think are important/helpful, I always clean the ends of the fittings (added insurance) measure the length of solder you need (estimate, not rocket science) 3/4" for 3/4" 1/2" for 1/2", etc. & last which I think he said; let the solder flow to the heat !
@vidaliasoleil27143 жыл бұрын
Best soldering tutorial I have seen on youtube! I have as much confidence in my joints as I do hiring a pro now.
@Got2Learn3 жыл бұрын
🤗🤗🤗
@frankmontez68533 жыл бұрын
I used to work for plumbing company as laborer helper. It's easy enough to solder. Prep work is very key. Don't over use flux. Don't overheat it. " Write " once around the joint that's it. Wipe off excess if need be.
@jimporter4 жыл бұрын
Apart from the cleanliness and preparation what made the biggest difference to my ability to produce good joints as a DIYer was a decent MAPP gas torch. Especially on larger fittings where there is more metal to heat, the ability to get good heat into the fitting quickly is a must.
@RustyorBroken Жыл бұрын
I've recently learned that mapp as we knew it hasn't been produced since 2008. The stuff that they sell in the yellow bottle isn't actually mapp. They intentionally call it map/pro to mislead the consumer. It only burns 100 degrees or so hotter than propane. Nowhere near what the old mapp was. The torch tip is far more important than buying today's yellow bottle. There are a couple of great videos that demonstrate this. I am no longer going to pay the premium price for a marginally better gas.
@techalyzer Жыл бұрын
It might have been right for you but I just checked the price of one and for that amount of money I'd redo half of my house's plumbing with all materials included. It is totally not worth it, I paid something like $12 for my torch.
@jgallone3 жыл бұрын
For the home DIYer - go and spend a few dollars getting sacrificial materials to practice with. A length of copper pipe, a few connectors and then just practice your soldering technique where there's plenty of room and you don't have to worry about ruining anything if you mess up. Could save you a lot of frustration and money in the long run.
@Got2Learn3 жыл бұрын
100% agreed 🙏
@johnmichaels43303 жыл бұрын
Yes. With this and literally every other contractor grade project.
@PaulCJakubik5 жыл бұрын
Good technique- I like seeing blokes with good hand skills. I'm a licensed plumber and take pride in workmanship. It's good to see someone promoting quality!!
@Got2Learn5 жыл бұрын
Thanks a lot buddy ;)
@frankmontez68533 жыл бұрын
Does this mean , you only use this technique for all your work ? Where do you work ? Never used the technique of leaving a thin neat but visible line of solder just barely around the joint ?
@walterdiaz20033 жыл бұрын
Rare to find good contractors who care. Good job.
@Got2Learn3 жыл бұрын
👌🙏
@victorvarisco53605 жыл бұрын
Good video and commentary but as I have 30 years sweating copper, I have no issue seeing a slight dribble/drop at a joint. On vertical, a wet rag wipe will do the job of a down-run dribble but at least you know there is enough solder in joint. I've seen 200 psi blowouts using too little solder. Also, best tip for cleaning a joint after a good sweat, is to take your flux brush and paint over the area while still hot. The heat and flux cleans the joint super bright. Just wipe with wet rag after and the joint looks bright. Gotta comment...but, where I come from I have NEVER heard "solder" pronounced as 'sold-er'. It is pronounced as 'sod-der'. "L" is silent. My expertise is 2" to 4" pipe joints using MAPP.
@victorvarisco53605 жыл бұрын
And I apologize if I offended anyone with my comments. I am a grumpy General Contractor.
@Got2Learn5 жыл бұрын
Hehe, at all ;)
@stephensomersify5 жыл бұрын
s o l d e r = solder in UK, home of English language
@victorvarisco53605 жыл бұрын
@@stephensomersify Population Britain 66 mil. Population US 328 mil. "sod-der". More plumbers.
@caiobabe5 жыл бұрын
I used the acronym MAPP generically as well as everyone else does these days when in reality and to be specific it is MAPP-Pro. It is the only thing you can buy for small single bottle torches bc real MAPP went out of production a decade ago. I loved the real thing. Burned hotter and faster than any single bottle gas. Did not need any type of "turbo" torch to use. Now with MAPP-Pro, one needs to upgrade their torch. I tell everyone to use the Benzomatic TS8000 when using MP. I do use a propane torch to bring cast aluminum up to high heat before welding to avoid cracking. Funny thing, on a job last year, customer says I was welcome to use what ever was in their supply room. I discovered 4 pristine and unused bottles of real MAPP. I took them all and gave customer back new bottles of MP.
@guyh.45535 жыл бұрын
I can TIG, MIG, Wirefeed, ARC, Oxy-Acetylene weld, and Braze but I've NEVER soldered. How crazy is that. Something I NEED TO learn. Looks pretty easy. Thanks!
@Got2Learn5 жыл бұрын
;) this is the place, have fun bud ;)
@Got2Learn5 жыл бұрын
@Hans Fuchs no, it's not.
@tomhollins92665 жыл бұрын
Wow an absolutely clear explanation as to what is happening and when. The technique is impeccable.
@Got2Learn5 жыл бұрын
Thank you Tom, share if you can :)
@startover1255 жыл бұрын
Got2Learn plumbers save lives throughout the day! Every day! That is why it's better to take a few extra minutes and make sure each job is correct and safe, and not be rushed by our bosses
@startover1255 жыл бұрын
Our bosses are not always out in the field, some of them are sitting behind a desk and counting the money that we make for them, but I can go home and sleep with a good conscious if I do it correctly and safely for the customer
@100PercentATP4 жыл бұрын
99% of professionals will never do this sort of work because it takes way too much time. You can't even pay good money and expect work like this these days with "professionals". I love youtube and contributors like yourself who make DIY a great alternative!
@Got2Learn4 жыл бұрын
Thank you very much, and yeah....people don't take the time anymore to do stuff nicely, oh well...
@f14tomcat303 жыл бұрын
I agree. Also will add that who cares what it looks like. Won't be seen inside the wall. If exposed to view then yes I'd want it to look good.
@giseliapereira5914 Жыл бұрын
Thank you for your video. Today I capped two pipes because your detailed videos gave me the confidence to do it myself. You know I must have been very confident because no one wants water damage in their house.
@raybenitez50310 ай бұрын
I do like to see the nice solder shine , just because it truly looks professional
@TheOldkid8885 жыл бұрын
Just a little tip to add that will save you from having any leaks after you have soldered. At the one minute 11 second mark in the video he shows flux on the pipe. I noticed the flux contains numerous amounts of small pieces of dirt. Those are the things that prevent the solder from running properly. So it is good to keep your flux covered when not using it. One small piece of dirt can prevent the solder from running into the entire joint. I am not bashing here...just pointing something out in this video that I did notice which should be corrected. Keeping every piece in the process clean will result in a watertight joint!!! Happy soldering!
@Got2Learn5 жыл бұрын
Thanks bro :)
@als10233 жыл бұрын
And using a clean cloth to wipe after sanding the copper. Thanks for your comments !
@luiszavala76644 жыл бұрын
Jaja aquí en mexico queda todo horrible. Thanks for the video man! I only wish this professionalism was appreciated in my country, blessings!
@Got2Learn4 жыл бұрын
Thanks for watching! :)
@dansr63335 жыл бұрын
Great video! Especially with the short clips on examples explaining what you are talking about. I've noticed while heating the fitting , the flux comes out. I wipe it with a rag( yes its hot) , then apply the solder mainly on vertical piping. Its clean enough to look professional. And no leaks!
@Got2Learn5 жыл бұрын
Good work bud, and thanks for the nice comment ;)
@DYIIdeas3 ай бұрын
We have a timber frame house with exposed copper piping for the fire suppression system. The plumber that did our joints did a fantastic job with just a small fillet of solder around the fittings. He went to the extra trouble to make the soldering look good because people will see his work for the life of the house.
@brasshouse-og4 жыл бұрын
Great video man I really enjoyed it and after plumbing for 16 years you taught me something. I will say this to the younger plumbers, 99% of your solder joints are in a wall or under insulation and will never be visible so I personally don't put any stock in to how pretty a joint is. A while back I called out to a fancy lab at 10pm to fix an emergency leak on a 3" chilled water line. While fixing it i was gobbing solder in it and not giving on fuck what it looked like and my apprentice (5th year apprentice in the UA plumbing union) asked me "don't you care what it looks like? Thats not pretty." I told him "We just cut out and fixed pretty, im hanging something up there that we ain't gonna have to come cut out in a year like this "pretty" work here." There is a time and a place for what this video teaches you, its not for every job though.
@Got2Learn4 жыл бұрын
Exactly! Yes, I mentioned somewhere in the video that I personally only use this for radiators and towel warmers and stuff like that where you have 1 or 2 joints that are exposed, other than that, there's no use for this method, unless you want it to look clean inside the wall..
@brasshouse-og4 жыл бұрын
@@Got2Learn pretty cool that I was able to learn a new technique after so many years in plumbing. For exposed joints all I've ever done is wipe the flux and try to control heat and just have a thin bit of solder showing. Never pulled off a flawless joint like that. Good video.
@jasonsmith64084 жыл бұрын
I had a plumber that tried to make his joints look like this. He had more leaks than anyone. He said he didn't want to waste and drip solder all over the place. I responded by saying I don't want to drip and waste water. Solder the joint, leave 1/8" around it and swipe the dog ear off. You will know it's full. Had to get rid of him after I saw him on a service call soldering 4" copper with a #4 prestolite tip. Dude wouldn't listen.
@Got2Learn4 жыл бұрын
It takes the same amount of time, just a different technique.
@charntsabre34634 жыл бұрын
I call them dog balls
@Got2Learn4 жыл бұрын
Lollll
@420Chameleon3 жыл бұрын
Oh dear...
@Userconcubinexp3 жыл бұрын
I always say solder is cheap . In a hard to reach spot I will let it drip . Finesse does not apply in this situation.
@flowerpt4 жыл бұрын
Got2Learn: this is for aesthetics Commenters: but it's not utilitarian! Thanks for showing us another option. I'm not going to use this joint but the license plate is great!
@rayc15035 жыл бұрын
We only flux the pipe not the fitting itself. Especially on Gas lines as they can't be internally flushed. Also the access flux is pushed into the pipe and can draw in solder which causes turbulence and restricts the flow. Videos spot on bro, you're right on the money. The inner top tip of the inner flame is the hottest part of the flame. This is why we use this to heat the joint. Mapp gas for me when I solder ✌
@Got2Learn5 жыл бұрын
Wooohoooo thx @ghost, glad you liked it bud!!
@rayc15035 жыл бұрын
@@Got2Learn pleasure as always bro, keep doing what you do best 😜
@richardhy69315 жыл бұрын
Natural gas lines should never be soldered joints, rather they should be flared to adapt to iron pipe main. If by “Gas Lines” you are referring to Medical Gases, these should also never be soldered joints, but brazed with a nitrogen purge.
@rayc15035 жыл бұрын
@@richardhy6931 Here in the United kingdom & Europe we use different thicker gauge copper. As the methanethiol added to gas to make it smell is lesser in content. The natural gas reacts very little with the copper. So Gas safety and use regulations states we can use copper. As it states appropriate fittings should be used. We cannot swage gas lines. Outlet gas lines from domestic meters are such low pressure and copper is actually the most common material used here. You have a different climate to us. So gas has a different thermal expansion to UK and Europe. Long gone are the days we used cast iron or steel for gas installations. I work commercial & domestic tiv & meter volumes can be extremely high in some cases. So the gas purge machine comes out quite often too.
@richardhy69315 жыл бұрын
It’s always interesting to see how things are done in other countries. Thanks for the explanation ghostman 👍🏼
@rickgillard22963 жыл бұрын
Awesome job. My grandfather taught me the basics 40 something years ago. This takes it to the next level. Thanks
@Got2Learn3 жыл бұрын
🤗🤗🤗🤗
@mrtrek642 жыл бұрын
Am I missing something? Are you suggesting that after 40 years you're ready to take it to the next level? 😆
@movazi2 жыл бұрын
Neat, thx. I used to just brush some more flux on the joint while hot, that would somewhat clean the joint, but nothing like what your joints look like.
@bitpro89035 жыл бұрын
Monster open mesh grit cleans like no other and last the longest. Emory cloth is time consuming. Also on bigger copper 1.25 and up you have to circle the fitting with solder to get a correct seal. Looks don't matter but leaks do
@Got2Learn5 жыл бұрын
Definitely!! It's also more expensive ;)
@bitpro89035 жыл бұрын
@@Got2Learn Time is money and redoing a leak cost money as well
@kevinr44545 жыл бұрын
Someone here asked: "How much solder do I use?" Until you get a true "feel" for soldering I'd recommend this - use about 1/2 of the diameter of whatever fitting you are soldering. Thus if you are soldering 1/2" pipe, use about 1/4" of solder. If you are soldering a 1" pipe - use about 1/2" of solder. And how do you know how much solder you are actually using? Well, if you need 1/2" of solder, bend a 90 degree angle at the tip or your solder so you physically have 1/2" of solder after your bend. If you need 1/4" of solder, bend the tip of the solder so that you have 1/4" of solder past the bend. It is VERY easy to add too much solder (and as this video showed) where you end up puddling the solder inside the joint. Truly, you need VERY LITTLE solder to make a sealed joint. When I was a novice I was installing a boiler and had soldered a 3/4" vertically mounted gate valve - and because of the mass of the valve I REALLY soldered that valve to make sure it didn't leak. Problem was - I had used so much solder that when the valve was opened (the gate was pulled back to open the valve) I had completely sealed the valve closed. I had created a solid solder plug! Yup - played hell finding that little error when the system wouldn't work. And that's when boss-man taught me the 1/2 the diameter of the pipe trick.
@bonsummers26575 жыл бұрын
Thank you very much for sharing that, key thing to know.
@normalhuman92605 жыл бұрын
I enjoyed and will try your tip as well. I do the samething, I worry too much about leaks that I use too much. Ty
@WesleyJolly3 жыл бұрын
My question would be, with what thickness of solder does the rule work?
@PaulCJakubik5 жыл бұрын
In Australia, silver brazing is the go- soft soldered joints haven't been used for years. In fact, soft solder is illegal on gas lines because if there is a fire the joints may fail.
@TRUE_GR1T5 жыл бұрын
you aren't allowed to solder gas lines in Canada.
@reezo6195 жыл бұрын
I kno rt
@TheRaceface225 жыл бұрын
Interesting . In the UK almost all domestic gas lines are copper soldered . The gas regs here are super strict aswell .
@sslightningbolts47845 жыл бұрын
@@TheRaceface22 just use John Guest pushfit .......it'll be ok 😂
@bobstratton63622 жыл бұрын
I have found over the years, good preparation and cleanliness is the biggest pat of all jobs and techniques. And then clean up afterwards. I like to even spray the pipes with clear coat when I'm finish with work that is highly visible. Great video though. Takes time to do good work. Takes more time to do it over.
@Richard-xj1kt2 жыл бұрын
Good lesson found this tutorial very useful
@Richard-xj1kt2 жыл бұрын
That tutoral will help me to do a better job next time I will look at the links you sent through later on thanks.
@Got2Learn2 жыл бұрын
Awesome!!!
@zackzander4254 жыл бұрын
Tinning flux is game changer. My joints always look impeccable. Keep moving the torch and put the heat where you want the solder to go. This isn’t a hard skill to master.
@josevillagomez25675 жыл бұрын
Watching this during my OSHA 10 hour Class haha good job
@Got2Learn5 жыл бұрын
Hehe, that's cool, have fun bud ;)
@johnjacobjingle83023 жыл бұрын
I tried during my osha 40 class but the drool messed up the screen..
@420Chameleon3 жыл бұрын
Still have my OSHA 10 card from high school! Good for life.
@OldsXCool5 жыл бұрын
Your channel is such a treasure.
@Got2Learn5 жыл бұрын
Very much appreciated, thx so much OldsXCool!!!
@citylockapolytechnikeyllcc79363 жыл бұрын
@@Got2Learn Bury the treasure in a copper box, and solder it tight with a pretty, no drip seam.
@theprophetez1838 Жыл бұрын
Just wanted to say thank you for the many good videos you have put out. They are well done and to the point.
@richreeder1786 Жыл бұрын
Very professional finished joints, thanks for telling us hacks to go with a little more flux, and what it looks like if you do
@Got2Learn Жыл бұрын
🤜🤛
@jacobmohr76234 жыл бұрын
I would say that does look very nice and beautiful. But most pros don't scrub their pipe after the job is done. You can reduce the life of the pipe because you are wiping the thin oil coating off the pipe. Instead while the pipe is still hot put some regular flux on top of and take a clean 100% rag and wipe it over your joint. Just make sure the solder solidifies first.
@johnbull53942 жыл бұрын
Depending on the flux, leaving flux on a pipe will result in it turning green, although it may look good initially. Most plumbers I know consider fluxing after soldering to be extremely bad practice for this reason. I suppose if you want to grease your pipe, though, a silicone grease could be used for this purpose. I don't generally use an abrasive to polish a joint, although copper, whether oiled or not, is generally extremely durable when exposed to air, so I can't really see what harm it would do (except that you are wearing away the wall thickness very slightly).
@ThePSPJesus4 жыл бұрын
At the end of the day and in all of my 15 years of plumbing Ive never had a leak on a solder joint other than once on a stub out that was cut lopsided by an apprentice and yeah that might look good but without a full bead around the rim of the fitting you just made a timebomb. I cant tell you how many times Ive been called out to a job where all Ive had to do is clean and re-solder a joint that looked nice and neat like these at the end of the day all you're really doing is being cheap. Heres a real pro tip, get you a box of clean rags keep a nice wet but not like drippy rag and wipe each joint it smooths drips and at least makes it look nice and shiny, same trick applies for smoothing beads of silicone too.
@Got2Learn4 жыл бұрын
Yeah, it could be a time bomb for beginners, this is not for beginners as I said in the beginning of the video, this is just to improve an already experienced plumber ;)
@alexmejia82965 жыл бұрын
For good clean solder joints practice makes perfect. My suggestion is to use the correct torch tip. The right size flame makes a big difference. Also wiping the excess flux after you pre heat the fitting. And finally let capillary action do the work. Practice controlling your heat
@Got2Learn5 жыл бұрын
Yup!!
@bonsummers26575 жыл бұрын
Wiping excess flux after pre-heating? Hmmm? I'm trying to make sense of that statement. What about the issue of the Flux evaporating too much and thus making a weaker seal between the copper sheaths?
@commadanteflet2 жыл бұрын
I think this comment just changed my life... wiping away the excess flux after preheating? I'm gonna try this.
@alexmejia82962 жыл бұрын
@@bonsummers2657 I’m talking about the excess flux that runs out of the fitting. And flux doesn’t evaporate it burns and turn black to the point where it won’t take the solder. To each his own. You only need a thin layer of flux on fitting and pipe. But if it’s running out out of the coupling or fitting it’s over flowing and I’m just saying I like wiping the excess because if you let it run every where you will end up with a sloppy joint.
@alexmejia82962 жыл бұрын
@@commadanteflet try it. If you just leave the excess there potential for the solder to stick or adhere to spots that you don’t want. And of course at the end of the day it’s about whether or not you solder joint can hold pressure. But I’m in Texas and a clean joint vs a sloppy joint in the commercial industry matters. It could determine how long you work with companies especially in the union
@slavenkomatijevic35454 жыл бұрын
Clean work. You are professional grade.No question ask.
@Got2Learn4 жыл бұрын
Thanks Slavenko!
@ve2zzz4 жыл бұрын
Hi.... Not related to this video specifically, but i saw other videos about bending straight copper pipe. My question: Is it possible to bend straight (type M) copper tubing without kinking it and if so, is it code to use bent copper pipe for potable water ? Thank you.
@Got2Learn4 жыл бұрын
It has to be soft/annhealed, if it's hard it'll just kink.
@bravobrk4 жыл бұрын
Why? Aesthetics? If not just use pex.
@lacro56864 жыл бұрын
@@Got2Learn My 1960 built house was plumbed mostly without fittings (ells) The potable water lines are L copper and the Hydronic lines are M copper, both hard copper. Almost all turns were done by bending the copper, and there are no kinks. Also no couplings were used, the pipe was swaged larger to act as a coupling. It's really nice to look at.
@Got2Learn4 жыл бұрын
@lacro niceeeeee
@snapdrag1413 жыл бұрын
The guy who opens the wall in 15 years is really gonna be impressed
@ev65582 жыл бұрын
Was about to say, literally no "professional" or homeowner cares about how the solder looks on a pipe that's inside a wall. These videos get made for people who have never and will never do this kind of work.
@humb1s3rvant8 ай бұрын
😂😂😂
@2002drumsonly5 жыл бұрын
Glad I subscribed and hit the bell in a prior video! Keep em coming. 10/10
@Got2Learn5 жыл бұрын
Thanks man, glad you liked it ;)
@2002drumsonly5 жыл бұрын
@@Got2Learn The quality of my work is improving thanks to your great videos. Enjoy watching them.
@Got2Learn5 жыл бұрын
Thx so much 2002, I really appreciate that ;)
@vp39704 жыл бұрын
I’m an old school plumber trained by union journeymen in the field and classroom. We (all locals-US & Canada) learn from expert from the Copper Development Association , these are the people that test and developed soldering pipes and fittings, they also investigate pipe failure in law suits. Some of the adages I’ve learned from the class: if you can see the flux you are using too much. A good soldered joint is one that doesn’t leak a perfect solder joint is one that doesn’t leak 30 years from now, wait, wait what? Think about it. A person doing a 3/4 inch pipe on you tube cannot say that a joint is good by just apply flux and solder. The only way to verify the joint is perfect is by inundating the pipe and hydro-pumping the water in the pipe to 200 psi. Normal operating pressure in a house is 60-80 psi. If your joints don’t leak you have a perfect joint. In Hawaii all piping in big building are tested this way by code🌺
@Got2Learn4 жыл бұрын
I used to do almost all my joints like this and we would run 120psi hydrostatic tests. I won't be a liar, some would leak, but that's because of where they were placed (very hard to reach), the others would do just fine.
@ralph17p4 жыл бұрын
Nice work. This video does show the difference between a pro and an amateur like myself. I mean, I get that result, but with a ton of elbow grease, needle files and emery paper after the fact. And then I polish and clear lacquer the result so it stays shiny...
@Got2Learn4 жыл бұрын
😉
@cerealkiller42484 жыл бұрын
When I was an apprentice soldering on site, a clerk of works pulled me on my joint prep. He told me to remove the fitting after I’d prepared it as normal, I then saw most of the flux wasn’t in the joint but had gone into the pipe itself, and was waiting to be heated after which it would run into the system ( heating/plumbing etc ). The same on the outside of the fitting, any excess flux would melt and hit the floor instantly. The solder itself was the same, the joint can only take so much solder, so, by adding too much it either ran into the system or down the pipe into the floor. My method now is - Clean both joint faces Apply flux sparingly with a brush Wipe any excess flux off Measure a piece of solder equal to the pipe circumference Bend that solder 90 degrees. at your measured mark Heat pipe gently as above, pull away as soon as solder is melting When the measured piece of solder is used your done. If you need to you can flick the flame over the joint to keep the heat melting the solder. Never use the flame to melt the solder Lastly, I use a piece of asbestolux board approximately 200mm x 200mm as a barrier against burning/marking wall etc. All plumbers/heating engineers have leaks, but, this method causes me no more issues leak wise than any other solderer.
@johnford90704 жыл бұрын
So it takes you 20 minutes to solder a joint
@cerealkiller42484 жыл бұрын
John I actually solder very little, I bend 15/22/28, and as a maintenance engineer, use copper tectite sprint fittings, very expensive but don’t have to worry about raising “hot works permits” and waiting 45 mins after last soldered joint before I can leave site. And my soldering method is very quick, no blobs of solder or flux to clean up from my work space.
@lacro56864 жыл бұрын
CerealKiller wrote: "Measure a piece of solder equal to the pipe circumference" If you follow that procedure, you will have a joint with three times the solder needed!! You should have said: Measure a piece of solder equal to the pipe diameter.
@cerealkiller42484 жыл бұрын
lacro I’ve gone off ‘Yorkshire” fittings, not an exact science I know, but it’s served me very well over 30 years.😀👍 I normally use them for every soldered joint, a little more expensive, but worth it for asthetics in my opinion. I never solder anything I can bend, I can pull half a dozen bends in a 3m length with precise accuracy. I use tube expanders to join lengths together having the female joint facing down below my eye-line, and facing upwards above my eye-line giving a seemingly jointless run of tube.
@isep88822 жыл бұрын
It’s nice to see these how to videos. One way I learned on the different methods was cut in half the coupling and hammer it flat after soldering. You will see how good your soldering method works. Try different scenarios, what happened when you don’t clean your pipe or fitting. Or when you don’t wear gloves and you leave finger prints on the pipe. I guess I should make a video too🤔
@ninjabothandyman60635 жыл бұрын
Excellent preparation technique and the method of heating the front 2/3 - 3/4 while not heating directly to the back and allowing whicking and capillary action to suck in the solder works amazing, and it's truly so much easier! ! I was fortunate to first learn just exactly the same identical methods for doing this myself (with the exception of the tinning flux) I've always used only soldering flux, but seeing the ease and coverage it provided--my life will be made even simpler along with faster progress for each joint !! Much thanks for sharing this video kind sir !! Keep up the outstanding work !!
@Got2Learn5 жыл бұрын
Glad I could help Ninja ;)
@mj32995 жыл бұрын
I also like pretty joints. I found that gently wiping the run or access solder with a dry rag or old leather glove while still melted, works wonders, the thin layer of tin that remains can just be cleaned up with emery paper. I sometimes re heat to wipe if necessary. It also works great if you use recycled pieces that have previously been soldered just heat wipe and you have a tinned pipe and not waste the precious copper by cutting it off. To clean soldered couplings, grab with longnose plyers heat and bump your hand against something solid the hot solder comes flying out. and you have a beautiful pre-tinned coupling that needs less solder and a non-leaking joint as a result. By the way I use LACO flux no leaky joints ever.
@msk3905 Жыл бұрын
Yup i wipe joints with a scotch bright pad after soldering and joints like great everytime
@__h17583 жыл бұрын
I love soldering It’s super satisfying 👍🏼
@illchoosemyignorance624 жыл бұрын
I'm doing a liquid cooled PC build, and wanted a kind of industrial look to it. I'm good soldering household pipes so they don't leak but they look awful. Thanks for the tutorial. Cheers.
@Got2Learn4 жыл бұрын
Awesome man, hope it turns out nice ;)
@UtwoBed5 жыл бұрын
The #1 should clean, and dry. Flux isn't for cleaning, it's to prevent oxidation during the soldering process. Any water present will ruin your solder because the water turns into steam and carries off the heat faster than your torch can heat. Also, what I do is cut off the wire brush handle and insert brush shaft into my cordless drill. Works much faster than doing it by hand.
@xingjuchen49195 жыл бұрын
UtwoBed 👍
@jamesvandivier22985 жыл бұрын
flux is to create capillary attraction to draw the liquid solder into the joint , main reason.
@edwardmclaughln66893 жыл бұрын
Piece of white bread in the pipe will keep the water back
@solartherm5 жыл бұрын
pretty accurate dude! 35 years doing it
@Got2Learn5 жыл бұрын
Awesomeee!!! Thanks a lot buddy ;)
@johnharding63944 жыл бұрын
Most fluxes are chemical reaction (Laco) if a little to much heat they rim run but they can look OK at the time of running even old for years but any movement they can just part. Ever flux is an acid-based and creates a better capillary action
@canonpatchell3 жыл бұрын
If your in the USA you cannot use acid based flux on potable water lines. It is prohibited in the IRC & UPC.
@swimshady44673 жыл бұрын
Thank you for your video. Do you have one that explains the process for Old Work? For instance if you’re removing a fitting I need to repair it it’s never gonna be as clean or you’re never gonna have a clean joint how do you do that?
@Got2Learn3 жыл бұрын
Thanks, yes right here: kzbin.info/www/bejne/bnq5aKJ9aZh3kJI
@swimshady44673 жыл бұрын
@@Got2Learn thank you so much. 🙏🏼
@Got2Learn3 жыл бұрын
🙏🙏🙏
@kerrybarneyiii12022 ай бұрын
Gonna learn this when I eventually make a full liquid cooled pc! Great explanations and demos!
@Got2Learn2 ай бұрын
@@kerrybarneyiii1202 nice project idea 💡
@freddifish41795 жыл бұрын
Flux also keeps your metal from oxidizing which is very important. As the metal heats up it will oxidize very quickly and that layer of oxidation will stop the solder from adhering to the metal. Other then that awesome video. Once a person does a few thousand joints it gets to the point that you don't need to worry about being so careful with the flux or having any solder drips. I haven't wiped a joint to clean it up in decades.
@Got2Learn5 жыл бұрын
Well said ;)
@geraispadilla2135 жыл бұрын
Just use Everflux and don’t drown it. Once around is suffice as long as you don’t move to fast. I like to curl the end of the solder. And if you have a drop, just run across it with the end of the solder. It’ll knock it right off.
@josephmcclure61865 жыл бұрын
I wipe after every joint to get the cherry off.
@cubancasanova4 жыл бұрын
Ever flux is the bomb! Only time I clean copper now is if it's absolutely filthy or oxidized.
@sergiohernendez87673 жыл бұрын
I dont know ever flux as I'm in a less fortunate country but you obviously have more sense than most of these jokers connenting lol.
@geraispadilla2133 жыл бұрын
@@sergiohernendez8767 It’s a white plastic container about 3 inches in diameter and it has a blue lid. Thanks. I went to an apprenticeship when I was a plumber.
@mrtrek642 жыл бұрын
Something I've learned over the years. Have you ever seen a leak on a soldered copper joint where it has both a bit of corrosion and a greenish color to it? That comes from wiping the copper with a metal scotch bright pad. Residual fibers from the pad react with the copper and its soldered joint. I would recommend wiping and cleaning with copper wool/scotch bright only. Excellent video.
@thatf_inguy82202 жыл бұрын
Thats not what its from. Its from residual flux (highly acidic) oxidizing the copper. To prevent this, wipe your cooled joint with isopropyl.
@mrtrek642 жыл бұрын
@@thatf_inguy8220 Can't say I agree with you. While the flux is indeed highly acidic due to the fact it chemically cleans the copper, it isn't going to cause a properly soldered joint to leak because it wasn't wiped properly. If soldered joints were this susceptible to leaks because of them not being wiped properly, I'd guess this technique of piping would never be accepted in the field of plumbuing and would have died in its infancy..
@louisvl102 ай бұрын
aww yessss, thanks for sharing! gonn try out that technique for my exposed pipes in my upstairs bathroom. i'll apply some lacquer on the pipes to keep them nice and shiny. i prefer exposed because it's an old house with lots of wood, wouldn't want the wood to rot from a small unnoticed leak and have my bath tub fall through the floor...
@capitaldd36933 жыл бұрын
I was just doing 2inch copper pipe - it was terrible. Silver solder and liquid flux. The joint took so much solder - it would run inside. I could see slight gaps b/t fitting and pipe, so I added a bit extra to make sure I was filling the gap. Maybe tinning flux would have worked better for me. I'm moderately ok with 1/2 copper but the bigger stuff was trickier. I need to do 3inch stuff too.... Thanks for posting
@Got2Learn3 жыл бұрын
Awesome, once you get the hang of it it's actually easier to solder the bigger stuff imo, did you see my video on how to solder 2" copper? Here's the link: kzbin.info/www/bejne/goacoHt4nbKZfZI
@capitaldd36933 жыл бұрын
@@Got2Learn I did not. I will study it feverishly. I used map gas which seems better than propane. I was considering brazing. I'm going copper-copper and some copper to stainless ferrules. It's a learning curve...lol thanks for the info 🥃
@Got2Learn3 жыл бұрын
@@capitaldd3693 cheers brother! 🍻🍻
@capitaldd36933 жыл бұрын
@@Got2Learn hey thanks. I just watched it - ya make it look easy. I think my torch is a factor - used map gas though but pretty much a generic torch with 4foot hose. Probably should consider the oxy/acet set up.(can use it around the yard anyway with the welder) i was outside and it was -10, that probably didn't help either. But it just seemed like the copper was a heat sink and not heating up. I was coming at the joint from the back as well. It's a learning curve for sure. Thanks again
@Got2Learn3 жыл бұрын
@@capitaldd3693 Yes, many factors can change the ease of soldering, it's a tedious thing when starting, just keep practicing 👌👌👌
@HVACRTECH-835 жыл бұрын
Always start soldering your lower joints and work your way up to joints that may be above on the same pipe,Especially on your vertical couplings you soldered,do the lower joint first as heat rises,once you do the bottom side,little heat needs to be applied to the top side. If you do the top first, then heat the bottom,you could create a leak on the top side that you just soldered
@JasonMontell2501 Жыл бұрын
Heat doesn't rise though. Hot air rises..
@HVACRTECH-83 Жыл бұрын
@JasonMontell2501 heat moves from hotter to cooler in any situation. In air, the hotter air rises because it's lighter than the cooler air,causes circulation as hot air rises and and the cooler air drops. When talking about heating a joint with a torch, same thing applies. The hot burning gas from your torch travels upwards. Never seen one yet where the flame comes out straight then heads downwards. You get the idea. Just try it you'll see a difference. Start at the top on one joint then try starting at the bottom. This is how harris taught us at live demos over 20 years ago.
@JasonMontell2501 Жыл бұрын
@@HVACRTECH-83 You're correct that heat moves from high temp areas to low temp areas but are somehow hung up on thinking that heat only does so in an upward direction like hot air.. Heat will travel in any direction, left, right, down, backwards or forwards as long as it's from a high temp area a low temp area. So once again, no.. heat does not act like hot air and rise. If that were true then after heating your pipe you'd expect that only the pipes traveling above your work would be hot but no.. the pipes are hot in equal directions away from your work.. And that's because heat does not rise. Only hot air rises.
@barrymilam57344 жыл бұрын
You did a good job, I've been a plumber for 47 years.....
@Got2Learn4 жыл бұрын
Thanks man!!!
@powerwagon37315 жыл бұрын
I use mapp gas, ream the female end of fitting and inner dia of tube and use Ruby brand flux that comes in a yellow can with excellent results. PS use very little heat when soldering baseboards because the copper is very thin and over heats easily.
@gdeangelkick4 жыл бұрын
Pretty sure I was taught to ream inside of the tube, and NOT the fitting. The purpose of reaming has not so much to do with the strength of the joint, but the torpidity of the water after the joint is done and the H2O is flowing. Torpidity at the joint will cause the joint to fail over time. Water will cut through rock with enough directed agitation - you want it flowing nice and smooth over the joint.
@62Cristoforo3 жыл бұрын
Not to put too fine a point on it but I believe it’s called cavitation, when a pipe starts to decay from inside due to uneven eddies and currents from a pipe that wasn’t reamed
@WesleyJolly3 жыл бұрын
@@62Cristoforo Not to put too fine a point on it, but cavitation is the result of torpidity at the joint.
@WillN2Go13 жыл бұрын
This is actually the correct method. Thanks, I've been sloppy too long. The only downside is glance inspecting a job to make sure no joints were missed. Something else. In urban areas as the bare copper takes on a patina the air pollution turns it black. Not attractive. I lived in Old Montreal in 1980 when the roof of Notre Dame Eglise was re-coppered. Over a few months through my studio windows I watched as it oxidized a beautiful bright green. A sign that the air even in downtown Montreal is very clean. A few years later I was living in Los Angeles where the Griffiths Observatory dome was also re-coppered. It turned black. They had to clean it off and then chemically patina it green. So a fancy final step to copper plumbing might be to chemically patina it to a nice shade of green. I worked for a sculptor who worked in bronze. His assistant would apply the chemicals, which were like flux, then heat it up with a torch. In a few minutes it would be good for the next several thousand years. There's a Department of Water and Power building near where I'm living now that used to be a beautiful patina'd green, then some suit decided it should be 'polished' back to bright copper. I thought they must have sealed the surface. Nope. It turned black, looks awful. When Shutters Hotel in Santa Monica California was being constructed, apparently the plumbers used leaded solder for some part of the potable waterlines. This wasn't discovered until much later after many of the walls were finished, expensive wall treatments applied, etc.... It all had to be torn out, the pipes replaced, etc... Must have been a huge lawsuit. What I remember growing up and using lead solder to sweat pipes was this troupe, "There's so little lead that none of it gets into the water. So it's safe." Until it wasn't. Gasoline was also leaded. We kids used to like the smell of car exhaust because it 'smelled sweet.' That was the lead (who knows what I could've accomplished had not plumbing, GM and Big Oil not conspired to expose my generation to lead. This is something else you guys can bash us Boomers about. ) The problem in Flint Michigan was when they switched from Lake Huron water to the more acidic river water; this little bit of acidity attacked the lead in the old pipes leeching it into the water. (I've been using a reverse osmosis system for the past 36 years.) There's a famous op-ed from the 1920s when lead was first added to gas written by a doctor who warned that this was just mass lead poisoning. Automobiles needed an octane boost to keep the engines from 'knocking,' there were two competing ideas: lead and ethanol. I think GM had the patent for lead and the oil companies also made more money. (Just another reason to never trust an oil company.) I do go on and on.... blame lead poisoning....
@kchididdy Жыл бұрын
Lead still used in general aviation. Anything with piston engine.
@frankmontez68533 жыл бұрын
Yeah this technique is good for those that want that. Mine is the in-between one where a thin neat line of solder is visible but not messy. Yes getting it just hot enough but not too hot. I've never used green scrub pad only emery cloth and fitting brushes. I'm not at all very experienced plumber only was a helper apprentice years ago. Clean it super bright then don't apply too much flux. Heat it just enough with mapp gas I don't use propane. Then once " write " around the pipe / fittings. That is , just use solder wire end and go neatly around the joint. But now am leaning heavily towards pex. With shark bite or just crimp on fittings I'm not sure yet.
@charleswilson45983 жыл бұрын
For most repairs, I have decided to use pex with crimp rings. There seems to be a difference of opinion about the longevity of sharkbites, but I haven't heard too many loud complaints about pex fittings, although I am sure there are some. Also, the pex stuff is cheaper once you get the tools. However, I don't know why I am worried about longevity since I am 81 and don't have that many years left either. :) I do have a couple of places where I am using sharkbite push ons in my washer pipes.
@leonard3k5 жыл бұрын
Worked in shipyard a few years, some pipefitter friends caused many many leaks trying to make those joints real pretty where you cannot even see the solder... unfortunately you cannot tell if the solder whet the pipe good all the way around (surface tension in solder). Bad idea taking priority of neatness too extreme... (Hey it's magic.. where's the solder?).
@Got2Learn5 жыл бұрын
That's why I said to only do this when you've been soldering for a long time, or else you run the chance of having a leak ;)
@Viper6-MotoVlogger5 жыл бұрын
Very awesome tips as usual. My brother is the guy that tends to overheat the joint lol. I don’t think I’ve ever used thinning flux, so that was quite interesting.
@Got2Learn5 жыл бұрын
Thx Viper6, always enjoy reading your comments ;)
@weirdfishweirdfish66365 жыл бұрын
Tinning flux will almost seal joint by itself but will also cause voids if over heated
@Viper6-MotoVlogger5 жыл бұрын
weirdfish weirdfish 👍
@oneeyedrone42935 жыл бұрын
I was picky at first, but once you get the hang of it ... I sweat multiple joints to get things going quickly, then wipe down all the joints so everything is cooled off. At this point it moves faster soldering than push connect fittings, cheaper, and more reliable long run. Thanks again for the tips.
@Got2Learn5 жыл бұрын
Good job!
@DestroManiak Жыл бұрын
This tinning flux tip is a winner
@grimawormtongue20142 жыл бұрын
Brilliant vid, handy for exposed pipework. Only thing I will say is that if you have a large amount of piping and soldering to do, you'll be there a good while.
@jcarney19873 жыл бұрын
I like to use the flux brush at the end and go around the pipe and make the over solder look like a paint job lol. I'm an HVAC guy though, so I normally just braze copper haha
@citylockapolytechnikeyllcc79363 жыл бұрын
Are you brazing, or soldering with oxy-acetylene and/or MAPP ?
@syaz43805 жыл бұрын
Finally this video came out
@Got2Learn5 жыл бұрын
Yeah I normally put them out on Sunday, but I felt bad to make you guys wait another day ;)
@bigpjohnson5 жыл бұрын
Helpful hint: Use Oatey 95 flux to solder, and keep a tub and brush of H2O flux with you. After you solder, brush the H2O flux over the soldered area. It cleans off all the darkening and staining immediately! Let it cool down a bit, then wipe with a damp rag. I re-piped my house in copper. Used H20 the first time but burned it (too much heat) and had a bunch of leaks. Re-did it with Oatey 95 and just used the tip of the flame to heat the fittings. ZERO leaks at first pressure test! Kept the H2O and cleaned the joints, looks really nice but it's all hidden under drywall now.
@Got2Learn5 жыл бұрын
Good job buddy!
@superchuck32595 жыл бұрын
After a few practice joints on junk pipe I got good at it. Don't expect to be a plumber without effort. It is a skill that needs practice. If I had to do work now, I might even do a practice joint. It has been years since I needed to join pipes.
@andrewbrown14934 жыл бұрын
do not wipe flux or anything after you solder. let it naturally cool as to not break the solder joint. DO NOT rush the cooling process with anything. and the flux is just a waste of recesources
@vanhattfield82922 жыл бұрын
There is a very easy way to make awesome looking joints. Apply the flux to the pipe and fitting and apply heat above the maximum depth of the inserted pipe, the flux will run out of the joint as heat is applied. Just before applying solder, wipe the joint with a relatively cloth and remove the excess flux then immdediately apply the solder to the heated joint. It will suck up into the joint perfectly and you will have a clean looking joint. Thius works for horizontal and verticle applications. As with anything, it will take a little bit of practice but is something anyone can do.
@belapcela Жыл бұрын
Thanks!
@Got2Learn Жыл бұрын
🤜🤛
@AlphaBobFloridaOverlord4 жыл бұрын
Nice work! I have great respect for people who work to take their craftsmanship to the next level!
@markwhite5344 Жыл бұрын
It’s such a good feeling knowing all your joints look beautiful and do the job right.
@cookinitmax5 жыл бұрын
Nice thanks for sharing! I'm new to this and from what I've been watching and how you are showing the way it should be done well I think those who are showing me are doing it wrong. It's hard to tell the boss their doing it wrong LOL.
@Got2Learn5 жыл бұрын
Hehe, there's multiple ways to get it done right, don't worry ;)
@paulmaxwell88514 жыл бұрын
Lots of cranky old men commenting here. Old-school guys who will never reconsider the way they do things. I've always done top-notch, tidy work, much like what we see in this video, and always had inspectors comment on my workmanship. They see the old-school guys and their sloppy work every day, so my work stood out. I worked in the hospital setting. The suggestion that an inspector will fail your work if he doesn't see an excess of solder forming a fillet is nonsense. My work was always pressure tested with compressed air and that was the only test that mattered. My neat, tidy work without drips and runs marked me as a professional. If you hire a plumber who doesn't care about how his work looks, find someone else. Looks do matter.
@beerbeforebreakfast3 жыл бұрын
Also how you cut out walls for repairs says volumes. Still waiting to see a square cut out by even 1 plumber. I'm the follow up drywall man, I've seen it all.
@harryclarencealexander9161 Жыл бұрын
Very good video, answered all my questions in 10 minutes. 👍
@Got2Learn Жыл бұрын
Great to hear!
@Foxtrot19672 жыл бұрын
Great idea and very useful for exposed work
@Got2Learn2 жыл бұрын
💪💪💪
@rayflores33985 жыл бұрын
Will work with minimal heat on type M copper. Try heating just the fitting on type L & K copper and you’ll have some leaks.
@miket21724 жыл бұрын
Ill stick to the traditional way leak free for 25 years i don't care how it looks
@CassieHoward79684 жыл бұрын
Your customer might.
@JAO9814 жыл бұрын
*You might not care how it looks, but in exposed pipes your signature will be the way you leave it, messy or clean.*
@geecee97704 жыл бұрын
I'm with you not necessarily messy but reinforced for pressure and vibration
@mdunbar0084 жыл бұрын
You sound like a typical "professional" plumber, charge outrageous prices for shitty workmanship. I'll trust a neat solder joint any day over one of your globbed up shit shows.
@darrenrichards48404 жыл бұрын
@@mdunbar008 made me laugh, with you all the way.
@Thesidingsworkshop5 жыл бұрын
I get what your saying but as a Pipe fitter of 27 plus years you still need to use more flux even on the cleaner looking joint. It stops the tarnishing of the fitting which in turn can cause a bad contaminated joint. I agree with preparation ect apart from using tining fluxs as depending on the brand some contain lead and for potable water well you know what iam on about.. The key to good joints is cleaning. Fluxing and the right amount of heat depending on the pipe size. Plus like others most people prefer to see a solder ring visable of around 2mm around the fittings. Personally for eg on the vertical 22mm joint you used to much heat and not enough flux.
@slip0n0fall4 жыл бұрын
What's the consensus on wiping quickly after with a damp rag? Grandfather showed me this many years ago.
@Got2Learn4 жыл бұрын
I never do it, but a lot of people do.
@gamadmex Жыл бұрын
Very good video. Soldering copper pipes is definitely an art, and my joints are not nearly as pretty. Considering I rarely have occasion to practice my technique, I am good with a non-leaking result.
@davidg56294 жыл бұрын
A piece of tile backer board works great as a shield, as well.
@Got2Learn4 жыл бұрын
Ya, there's a few things that could be used for this application ;)
@jtoker97583 жыл бұрын
I think the copper pipe looks better with that visible ring of solder around the fitting. If you do it right, you can have it come out to the width of the solder and looks real clean.
@Userconcubinexp3 жыл бұрын
I agree that a uniform ring of solder looks good . Plumb and level looks good too.
@josec4395 жыл бұрын
I don’t know why I’m even watching this at 2am... I don’t work in a field near this... but good video
@Got2Learn5 жыл бұрын
It's always a good time to learn ;)
@ve2zzz5 жыл бұрын
Believe me... it's an excellent video to watch even if you're not a plumber. This will help you see if the joints are well made in your home. I've prevented a major water damage at my mother-in-law's house by repairing an absolutely awful and fragile joint that could burst at anytime.
@Viczhu09 Жыл бұрын
that's exactly how i do soldering, learned from a teacher in tachnical school years ago . every step is important, especially the heat...