Thank you, truly answering the "little questions" that were massively helpful for me. I appreciate you.
@essentialhandyman11 күн бұрын
Glad it helped you my friend. Please remember to hit the subscribe button and watch a few of my other videos for more helpful tips. Thanks.
@paulkramer41762 жыл бұрын
thanks for the video. I've been doing a LOT of paint removal recently. I have a few comments. I think a combination of process is good. I use a heat gun to get the bulk off. When using a heat gun, you did a small area, then scrapped, then repeated. I found that it is much better to just wear gloves, and to push a scraper (spatula) into bubbling paint, constantly keeping the gun on paint right in front of the scrapper. After all is scrapped, then use a chemical remover. If you use the chemical remover first, it is MUCH messier. But if you have the bulk of the paint off, the chemical remover is pretty good, get's into the grain a bit too. FINALLY, finish up with sandpaper. A Random Orbital sander is the best, most aggressive without leaving so many scratches. The torch of course works well, cause it has a lot more heat than a heat gun, but if you use a torch, you have a lot more possibility of a fire.
@essentialhandyman2 жыл бұрын
Thanks for watching and commenting Paul. It’s great to hear other people’s ideas. You’re right, when you strip wood with heat, you should keep the heat ahead of where you’re scraping, so it’s heating up the next section, while you’re scraping off the bit you’ve just heated. I couldn’t do that on my small area as I didn’t want to go over the marked area. I’ve never used chemicals after heat. I tend to go for sandpaper after heat.
@cynthiaskaggs6645 Жыл бұрын
Which methods work best also depends on what type of paint was used, the age of the paint, how many layers- and thicknesses- there are as well as what’s underneath. I’ve found that for multiple layers of thick paint a heat gun first then stripper works well especially if the wood was initially sealed with a clear coat before it was painted. For a single layer of paint or two thin layers, a sander is the way to go. I’ve never used a blow torch for fear of damaging the wood underneath.
@JiniReddy3 жыл бұрын
I bought a table from a thrift store and it has many layers of paint, I used 40 grit sandpaper and only did half the table and came to youtuvbe to find easier ways. The wood under is beautiful, don't understand why anyone would have painted over it 🤷♀️. Your video was so informative and it helped me make a decision on how to remove the paint easier. The sanding would have been ideal had it not been so many layers of paint. Thank u for taking the time to show us.
@essentialhandyman3 жыл бұрын
My pleasure Jini. I’m really glad it helped you. That’s what this channel is all about. Sharing knowledge to help others. Feel free to subscribe to pick up some more great tips.
@tinaknutsen2 жыл бұрын
Great video. I also came here searching for how to remove layers of paint on an ornate piece of furniture from the 1800’s ….hoping to find out how to remove paint in all the crevasses of the wooden inlays without damaging the ornate features. It looked like you had 1 layer of a freshly painted sample board which if you did the same test it would vary on actual old paint from over a hundred years ago due to completely different formulas and. It’s known that most of the paints had lead. I appreciate you going straight to the point and showing the various techniques and timings of each method. Well done sir!
@richstevenson1 Жыл бұрын
Thank you for making this video! This is very very informative! I can’t tell you how much I appreciate this!
@essentialhandyman Жыл бұрын
Glad it helped you Richard. That’s the goal of my channel, to help others. By way of thanks, there’s no better way to show appreciation than to hit the subscribe button, hit the notification bell and watch a few of my other videos. Cheers.
@glendahyde40353 жыл бұрын
Thank you. Your video keeps me from having to experiment and figure it out. Appreciate it. Sanding is the way to go for me! Best to you from Texas!
@essentialhandyman3 жыл бұрын
Glad I could help Glenda. Please sub for more tips like this. Happy new year to you.
@17Mikal Жыл бұрын
Wow ! The 60 grit sandpaper hand held machine was by far the fastest and best
@essentialhandyman Жыл бұрын
Hi Mikal. Yes it was. To be honest with you, it surprised me how much quicker it was. But, results like that are what make such videos more enjoyable. Please remember to subscribe to my channel, hit the notification bell and check out a few of my others videos for more great tips.
@asal15992 жыл бұрын
Nice video showing different methods.I hope to try out 2 of the ones you showed. I'll keep my fingers crossed it works out.
@essentialhandyman2 жыл бұрын
Thanks for watching and commenting. Good luck with your project. Please subscribe for more great tips.
@kerplop22632 ай бұрын
excellent voiceover! perfect levels! 🎉
@essentialhandyman2 ай бұрын
Many thanks. I appreciate your feedback.
@mickstr5295 Жыл бұрын
Very helpful tests. Your an old school blowtorch man, just like my dad was. That smell always meant he was decorating. Fun times helping and learning as a kid. Appreciate the video.
@essentialhandyman Жыл бұрын
Thanks for watching and commenting Mick. You're right, I am more old school, as like you, I learnt from my dad. He was also old school, preferring the tried and tested methiods, rather than being too adventurous. Please remember to subscribe to my channel and hit the notification bell. So you can see my new videos as I release them. Cheers.
@DanielaRougeАй бұрын
Splendid! Just what I was looking for! Thank you!
@essentialhandyman11 күн бұрын
Glad you liked it Daniela. Please remember to hit the subscribe button and watch a few of my other videos for more helpful tips. Thanks.
@JoJo-op5xy6 күн бұрын
Sander and heat gun are my go to
@kimberlywatt1842 жыл бұрын
Thank you for sharing this. You saved me a lot of time and money, not to mention my families health! Blessed be ❤️🌞✨🌝🤗🕯️
@essentialhandyman2 жыл бұрын
Glad I could help Kimberly. Feel free to subscribe, hit that notification bell and watch a few of my other videos, for some more great tips. Clicking on this link and buying me a coffee is always well received. www.buymeacoffee.com/essentialhandy1
@tooladdict74634 жыл бұрын
39 seconds some papers got to be the winner :-) and it left a nice finish as well
@essentialhandyman4 жыл бұрын
I couldn't believe how qucikly it dusted that paint off.
@mohammednasirmiah77152 жыл бұрын
Yhis video has given me an insight on how to remove gloss paint off the staircase. As my builder has been sanding whilst doing other stuff . Heat gun defo speeds the process up.
@essentialhandyman2 жыл бұрын
Glad you found the info helpful Naz. Good luck with the project. Please subscribe for more great tips.
@RyanKassel2 жыл бұрын
Congrats on your 1st voice-over 👏 Also, I learned from this video. Thank you!
@essentialhandyman2 жыл бұрын
Thanks for watching and commenting Ryan. Glad it helped you. Feel free to subscribe for more great tips.
@carolineramage74805 ай бұрын
That was really helpful. Thank you.
@essentialhandyman5 ай бұрын
Thanks for watching and commentig Caroline. Glad it helped you. Please remember to subscribe and watch a few of my other videos, for more helpful tips.
@kellyswann25233 жыл бұрын
I am completely new to paint removing. Before paying to get someone in I want to have a go myself. This video was exactly what I needed. Thank you. Excellent no nonesense, informative content.
@essentialhandyman3 жыл бұрын
Thanks for watching and commenting Kelly. My little channel is all about passing on my knowledge and hopefully helping some people. So it's really nice to hear that I helped you. Good luck with the project!
@kennethamend85572 жыл бұрын
Very nice. I just purchased my 1st house and the interior trim has multiple layers of paint. I've been sanding, with an electric sander. Im definitely going to change it up!!
@essentialhandyman2 жыл бұрын
Thanks for watching and commenting Kenneth. One word of warning about sanding old houses with multiple layers of paint, is the risk posed by lead paint. Sanding that down can be terrible for your health. Especially for a baby in the house. I’d advise you get it tested for lead paint before you do anymore work. Feel free to subscribe for more great tips.
@kennethamend85572 жыл бұрын
@@essentialhandyman I definitely will. In fact, I noticed when I slightly removed 1 baseboard, there was plaster or lathe. What should I secure the baseboards with? Finish screws or nails from a nail gun?? Also I need to make sure I Mark studs...hoping stud finder will detect, thru that depth. Thank You!!!
@diannadiress81482 жыл бұрын
Thank you for the excellent demonstration! It looks like I would definitely steer clear of Nitromors because of the caustic chemicals and definitely steer clear of the blow torch because well, flames. I must admit that I was nervous watching you with the portion of the board treated with those flammable chemicals next to the portion where you used the heat gun and blow torch in such close proximities.😳 Based on this video, I believe I would be more comfortable using a heat gun or sander. I appreciate your clear explanation of the different scraping tools used as well.
@essentialhandyman2 жыл бұрын
My pleasure Dianna. Many thanks for watching and commenting.
@geng8667 Жыл бұрын
Very interesting. Thank you for the info.
@essentialhandyman Жыл бұрын
Thanks for watching and commenting Gen G. Please feel free to subscribe for more great tips and useful content.
@chriscowles11859 ай бұрын
Nice format. I’m stripping paint off 1965 plywood sailboat. Inside and out. I will probably use a variety. 60 grit was VERY SLOW. 120 grit medium belt sander got 80-90% off then palm sander 60 grit. I prefer the sander with point on one side. Tomorrow the 40 grit sandpaper arrives. Let’s see if it beats the belt sander! Oh, tried the Citrus orange water based stripper but this paint was too tough. I’ve had mixed results with Citrus. Nice to work with if the job is right.
@essentialhandyman7 ай бұрын
Make sure you're wearing a decent mask when stripping inside the boat. Especially if there's carbon fibre involved. The sandpaper really blasts through ther paint doesn't it? I've never tried the citrus orange product myself (I don't think they have it here in the UK) but I've heard mixed reactions about it. Thanks for watching and commenting. Please remember to like the video and subscribe to my channel for more helpful advice.
@marksn40202 жыл бұрын
Good experiment and handy info to know
@essentialhandyman2 жыл бұрын
Thanks for watching and commenting Mark. Please help me out by subscribing and watching a few more of my videos. Cheers.
@Vavaxman3 жыл бұрын
Great video sir. Love the detailed comparison.
@essentialhandyman3 жыл бұрын
Thanks for watching and commenting Vasily. Feel free to sub for more great tips.
@nimmamimicrydayanand25772 жыл бұрын
Good thanks from Bangalore India
@essentialhandyman2 жыл бұрын
Welcome Mimicry. I think you’re my first Indian commenter. Glad to have you here. Feel free to subscribe for more great tips.
@nicolemitchell4463 жыл бұрын
I think it depends on what you are stripping and the paint you are trying to remove. I found the heat gun amazing for a piece that had a laqued/varnished finish that had primer and paint over the top. The varnish bubbled immediately and scraping removed all the layers! Just a little residual varnish that was then brittle and sanded off with a quick sand.
@essentialhandyman3 жыл бұрын
Thanks for the comment Nicole. Sounds like the heat gun is the way to go in that situation.
@JazzyScat2 жыл бұрын
Yes. Sander is good for 1 orvtwo coats of paint especially if it's old and dry but would be a nightmare of clogged sanding papers abd would cost much more. Heat gun one time small investment.
@crusty21 Жыл бұрын
I'll go with sander and heat gun..Got to do a whole stair case like this. Some genius painted and clear coated over the wooden steps and it looks like a total crap out. I hope this works because the place needs to be rented out in week.
@essentialhandyman Жыл бұрын
Clear coat on steps also carries the danger of it being slippery, especially if it were to get wet. Best to remove it, as you say. Good luck with the project. Please remember to subscribe to my channel and watch a few of my older videos for more gret tips and advice.
@jr53892 жыл бұрын
As an Apprentice Painter & Decorator 45 years ago it was the Blowtorch 🔥 HOWEVER it’s very easy to set your HOUSE 🏡 ON FIRE 🔥 🚒 🤬🏴😎 ps some people put news paper in old wooden windows to stop the draft 🌬 50 years later 🔥🚒🚒🚒🚒🚒 🤔🏴🤪
@essentialhandyman2 жыл бұрын
True. I've lost count of the old sliding sash windows I've replaced that stuffed the void between the frame and the brickwork with old newspapers. That was what they used before expanding foam. The blowtorch is my go to method on windows. But sanding on big flat surfaces and Nitromors on metal. Thanks for watching and commenting. Please subscribe for more great tips.
@neiljohnson53513 жыл бұрын
Nitromors bit dangerous for ones bank account too! Great video as I procastinate half way through my staircase...
@essentialhandyman3 жыл бұрын
Very true Neil. It's not a cheap product. Thanks for watching and commenting. Hope your project went smoothly.
@DarrylHart2 жыл бұрын
Cheers boss. Really helpful.
@essentialhandyman2 жыл бұрын
My pleasure Darryl. Thanks for watching and commenting. Feel free to subscribe for more gret tips and hints.
@DarrylHart2 жыл бұрын
@@essentialhandyman Will do mate. I'm going to buy an orbital sander I think. I've got quite a large area of wooden board where the paint is all flaky on my outside porch. Get that sanded and painted, well when the weather warms up and is dry 😆
@sisirose98502 жыл бұрын
Thank you… great video 👍
@essentialhandyman2 жыл бұрын
Thanks for the positive feedback Sisi. Please subscribe for more great tips.
@philskyross3 жыл бұрын
Top video; very helpful
@essentialhandyman3 жыл бұрын
Thanks Phil. Feel free to subscribe for other great tips.
@cassiawhitfield7280 Жыл бұрын
Top man!
@essentialhandyman Жыл бұрын
Thanks Cassia. Please remember to subscribe, hit the notification bell and watch some of my other videos for more great tips.
@nimmamimicrydayanand25772 жыл бұрын
Good job
@essentialhandyman2 жыл бұрын
Thanks for watching and commenting Mimicry.
@karlathwaitesgaming28533 жыл бұрын
I appreciate your video
@essentialhandyman3 жыл бұрын
Thanks. I appreciate you watching and commenting.
@michaelkitchen60002 жыл бұрын
Satin or latex paint?? Also, the sander did the best looking job
@essentialhandyman2 жыл бұрын
To be honest Michael, I don’t know what type of paint it was. I just found an old piece of painted timber, to do the test on. Thanks for watching and commenting. Please remember to subscribe and watch a few of my other videos, for more great tips.
@camstocks16572 жыл бұрын
Great video. What would you use for skirting?
@essentialhandyman2 жыл бұрын
Thanks for watching and commenting Cam. If I was going to paint the skirtings again afterwards, I'd just rub them down with a couple of different grits but if I wanted to strip them back to bare wood, I'd probably take them off of the wall, so I could work on them at waist height, rather than spend hours bending over. Then use a palm sander on any flat sections and a blow torch with shave hook on the profiles, finsihing off with a detail sander or hand sanding. Sandpaper wrapped around dowels makes sanding inner curves much easier.
@camstocks16572 жыл бұрын
@@essentialhandyman thank you!
@rhys1806062 жыл бұрын
All depends on how old paint is ,how many coats. Age of paint. Detail of surface. Good video
@essentialhandyman2 жыл бұрын
Agreed. Always handy to have different options available in your skillset. Thanks for watching and commenting. Please subscribe and check out some of my other videos.
@Sandbag13002 жыл бұрын
Agreed. I recently did some outdoor trim work that had multiple layers of paint and lots of cracking. The Wagner heat gun set at 1300 degrees and high fan level worked very well and it removed all of the cracked paint efficiently. Sanding would have never worked.
@essentialhandyman2 жыл бұрын
@@Sandbag1300 glad to hear it worked Sandbag.
@graceproby26623 жыл бұрын
I’m stripping my front door back to the wood to repaint and learned a lot from this video.
@essentialhandyman3 жыл бұрын
That really good to hear Grace. I hope it all goes well for you. My channel is all about passing on experience and those tips and tricks, to others who will hopefully benefit from them. And comments like your let me know the info is getting through to the right people. Feel free to subscribe for lots more handyman hacks!
@chrystalflippo81442 жыл бұрын
thanks
@essentialhandyman2 жыл бұрын
You're very welcome Chrystal. Feel free to subscribe for more great tips.
@frank88ster8 ай бұрын
What about using 'needle stripper' or sand blasting??
@essentialhandyman7 ай бұрын
I've never heard of needle stripping woodwork before and sang blasting would probably prove quite costly. Although I'd be up for trying both. Maybe a topic for a future video? Thanks for watching and commenting.
@msk39054 ай бұрын
My experiences with a heat gun are completely different, paint bubbles up then comes right off leaving an excellent stripped surface
@essentialhandyman4 ай бұрын
Sometimes it goes that way for me too. But it depends on the substance I'm trying to remove. Thanks for watching and commenting.
@Sadidesifamily3 жыл бұрын
My stairs barrister has many layers of paint and possible lead paint somewhere. Alot of gloss layers. I know the new nitro isn't as effective as the old one as the ingredients have changed. I am thinking of going the heat gun route as long as im masked and the hallway ventilated. But i do have an orbit sander....What would you advice? Thanks
@essentialhandyman3 жыл бұрын
Thanks for watching and commenting Saf. Most importantly, please be very careful rubbing down anything with lead paint. Especially if you haves a young child or baby in the house. A Client of mine was told the autism in their son was caused by them rubbing down lead paint in an old listed house. Because the airborne lead particles attached themselves to the haemoglobin cells, instead of the preferred iron molecules, needed for development. Please consider subscribing for more top tips.
@essentialhandyman3 жыл бұрын
Very difficult as lead paint is so harmful. Personally id take all the spindles and spacers out and use Nitromores on them, outside in the garden. The rest of the staircase (newel posts, stringers, handrail etc) I’d try the heat gun on. But as you say, it needs to be very well ventilated, doors to bedrooms etc., sealed up, masks on etc. See my other post about risks of inhalation. If in doubt. Just overpaint them.
@chrislc353 жыл бұрын
im doing a banister right nopw, has a lot of paint layers. heat gun works a treat for me, will sand it to finish off tho.with the heat gun, wait til it bubbles, then scrape, comes staright off.
@essentialhandyman3 жыл бұрын
Sounds like that'll keep you busy for a few evenings. If you've got damaged spindles, check out my video on how to fix broken spindles. Thanks for watching and commenting. Good luck Chris.
@chrislc353 жыл бұрын
@@essentialhandyman almost done. keeping the heat gun on for a little longer , paint just peels off. altho i shoulda worn a mask. only doing the handrails. altho the spindles are a bit rough. so will check out more of your vids :)
@essentialhandyman3 жыл бұрын
@@chrislc35 CHeers Chris. Feel free to subscribe for all sorts of helpful tips. YNWA.
@drakorez2 жыл бұрын
And we have a winner.
@essentialhandyman2 жыл бұрын
👍🏼
@jackwardley36263 ай бұрын
Also this is water based paint doesn't blister with heat just softens it
@essentialhandyman3 ай бұрын
I don't think the water based paints have a patch on oil based paints for durability and workability. They do smell a lot less though.
@jackwardley36263 ай бұрын
@@essentialhandyman yes oil based is definitely better especially for interiors there are 2 water based ones that are as good or almost as good but i think there for interiors only
@WorcestershireCommemorativeCoi Жыл бұрын
What about using wire wheel on a drill to strip it?
@essentialhandyman Жыл бұрын
That would most likely work but unless you were going for a very rustic look, it would most likely create a very uneven surface.
@WorcestershireCommemorativeCoi Жыл бұрын
@@essentialhandyman Good point mate, thanks for pointing it out
@Swenser3 жыл бұрын
Keep heat gun circling ahead of section you are scraping at and use bigger sturdier scraper for a quicker workout.
@essentialhandyman3 жыл бұрын
Great advice there David. Thanks for watching and commenting.
@jpenneymrcoin68512 жыл бұрын
how you like them burning paint fumes? holy mackerel.
@essentialhandyman2 жыл бұрын
A necessary evil if you're gonna use the burning paint method I'm afraid. That said, most of the times I've burnt paint off is usually the outer frame of windows, so fumes are not really an issue. Thanks for watching and commenting. Happy new year to you.
@KM-hn8ce2 жыл бұрын
Well, that was a scientific experiment.
@essentialhandyman2 жыл бұрын
Thanks for watching and commenting. Feel free to subscribe for more ‘less scientific’ experiments.
@Knifemaresama2 жыл бұрын
I would be to afraid of using the blowtorch. It is dry outside, and its an old house. Thank you for a great video, showing the different ways.
@essentialhandyman2 жыл бұрын
Thanks for watching and commenting. Please subscribe for more great tips.
@louisl50863 жыл бұрын
I'm sanding my banister. Some very awkward angles so hoping a good paint stripper will help take them odd bits away for a clean finish
@essentialhandyman3 жыл бұрын
Paint stripper, patience and elbow grease. Good luck.
@louisl50863 жыл бұрын
@@essentialhandyman cheers buddy. I've been working so not been able to finish. But I purchased a paint thinner which seems to help soften them odd angles
@essentialhandyman3 жыл бұрын
@@louisl5086 Not sure where in the world you are but Nitromors works really well in nooks and crannies if you can get it.
@louisl50863 жыл бұрын
@@essentialhandyman I'm In the uk. Yeah I came across that but with kids in the house I wasn't sure if the smell might be to much. I ended up getting something called bartoline tx10 paint and varnish stripper on amazon. It had good reviews so why not.
@essentialhandyman3 жыл бұрын
@@louisl5086 Let me know how you get on with t and the project.
@mimosveta2 жыл бұрын
basically as expected. I'm stripping a door frame, so I'm using chemical stripper as it's easier to hold the scraper up than the sander, but once that is done, I'll 100% have to sand it too, what can you do...
@essentialhandyman2 жыл бұрын
Good luck with the project. One thing that many don't remember... Unless you're stripping back to bare wood and are gonna varnish etc., there's no need to go back to bare wood. If you're just going to paint it, rub down by hand until the nibs are gone, give it a quick fill and light rub down and start painting. If you could help my channel by subscribing, hitting the notification bell and watching a few more of my handy videos, it would be very much appreciated. Cheers.
@FixItWithMe6 ай бұрын
I have to do an exterior door trim as well and have no idea how to start. The paint is starting to peel off. So do i need to remove all the paint off, or only the parts that are flaking off? I’m also confused as to what primer to use before painting. Any help would be appreciated! :)
@Artiej0hn0Ай бұрын
What about airborne Lead?
@essentialhandyman11 күн бұрын
That's definitley something to be careful of. I'd recommend full PPE, good ventilations, do outside if you can and keep all other humns and pets away from the dusty area.
@Artiej0hn011 күн бұрын
@@essentialhandyman Thanks. Unfortunately it would have to be indoors.
@MrsOpitz2 жыл бұрын
What's the purpose of puncturing the sandpaper? I have never puntured them😳😅
@essentialhandyman2 жыл бұрын
Thanks for watching and commenting Paulette. The holes allow the dust to be sucked through them into the dust bag (or shop vac, if you have it fitted) instead of staying on the surface. If you don’t disperse the dust, it clogs up the paper and makes it less effective. Please subscribe for more great tips and advice.
@hremaddox2 жыл бұрын
@@essentialhandyman ah, good tip! Didn't know that!
@essentialhandyman2 жыл бұрын
@@hremaddox glad I could help Heather. I always answer comments so if you’ve got any questions, ask away. Please help me by hitting the subscribe button and the notification Bell and check out some of my other videos. Cheers!
@BWeezy-sw1wy3 жыл бұрын
I have an entire house that has T1-11 with hundreds of hairline cracks. When I try to scrape it it has a variety of sized that come off. Sometimes nothing comes off it’s just a hairline crack and priming it 2 times followed by 2 coats of paint results in the same hairline crack in the paint. I tried an orbital paint eater and it it’s ok since it will take it to the wood surface and beyond but I have to put a lot of forced into it while on a ladder. I think I will try to the torch method and hope the primer sticks afterwards.
@essentialhandyman3 жыл бұрын
I’m assuming you’re in USA or Canada. What does T1-11 mean and where are your cracks? Internally or externally?
@essentialhandyman2 жыл бұрын
B. Weezy, I'm doing a video on how to fill cracks etc., at the moment. I think it will help you with making sure the cracks don't come back as bad. Keep your eyes peeled for it soon.
@maddierosemusic2 жыл бұрын
T1-11 is barely worth saving. You might try a 3" razor shaver to shave off the paint. (like you would use to shave wallpaper off a plaster wall.) Why not just use a belt sander quickly and use the time saved to work another job to save $$ and put up some proper siding like Hardie Board? T1-11 is the lowest of the low quality "siding".
@shaunsavage37502 жыл бұрын
Can you do one with multiple layers of paint please
@shaunsavage37502 жыл бұрын
With a mouse sander
@essentialhandyman2 жыл бұрын
Hi Shaun. This was multiple layers of paint. I’d guess half a dozen or so. I think a mouse sander would give similar results, as it’s essential the same tool but shaped to get into corners better. Thanks for watching and commenting.
@essentialhandyman2 жыл бұрын
@@shaunsavage3750 feel free to subscribe for more great tips.
@ashnwry47952 жыл бұрын
Friendly awareness to all diy viewers: using liquid gel, heat gun, Flame torch or sander to remove paint is extremely unhealthy if adequate precautions are not followed!!! In particular if you are working indoor. If you are removing old paint or a few layers of paint it’s even more dangerous to health if you or anyone else breath the particular around you so please take good care while doing such products.
@essentialhandyman2 жыл бұрын
100% agree. Can’t be too careful.
@7colliemac2 жыл бұрын
If you want to get paint of really quick use 40 grit sand paper.. then smooth it out with 80 grit after.
@essentialhandyman2 жыл бұрын
40 would definitely be quicker than 60 but when you factor in the time needed to change the grits and the second pass, would it be quicker? Hmmm, sounds like the subject of another video 😉
@roamer41398 ай бұрын
Removing paint with a torch is illegal in most instances in the USA, largely, due to the likelihood of lead-based paint being involved. A torch will make a gas out of the lead, it gets far too hot.
@essentialhandyman7 ай бұрын
To be fair, that's not a bad law. I almost always only ever heat strip paint externally. Usually on old single glazed windows and/or doors. Thanks for watching ands commenting. Please remember to like the video and subscribe to my channel for more helpful advice.
@ruger60495 ай бұрын
No sanding if there is lead paint in the mix.
@essentialhandyman5 ай бұрын
Agreed. Much safer to leave well alone. However, if you have to, take outside (prefably on windy day)and use lots of PPE.
@georgepaul161310 ай бұрын
Use nitromors for lead paint, you do not want to heat or aerosolise lead laint with sandpaper.
@essentialhandyman10 ай бұрын
That's very good advice. Especially if you have a newborn in the house. Thanks for watching and commenting.
@georgepaul161310 ай бұрын
@@essentialhandyman nitromors didn't work on the skirting I'm trying to strip so had to use a heat gun (empty newly bought house and wore respirator)
@7628739 Жыл бұрын
If you're not careful with a blow torch and you have insulation behind or have anything combustible behind the surface , you can start a good fire.
@essentialhandyman Жыл бұрын
Definitely Mark. On larger building sites I manage, we have a system called 'hot works permits' that are in place to deal with exactly those sort of situations. Thanks for watching and commenting. Feel free to subscribe and check out a few of my other videos for more great tips.
@Artiej0hn0Ай бұрын
What about Infrared?
@essentialhandyman11 күн бұрын
Thanks for watching and commenting. I personally have never used infra red. Do you find it works well?
@Artiej0hn011 күн бұрын
@@essentialhandyman I have yet to try it. Is Lead Vapor an issue with Heat Guns?
@essentialhandyman11 күн бұрын
@@Artiej0hn0 I'm gonna have to admit I don't know the answer to that question. Sorry.
@miyakinney52942 жыл бұрын
Wish I watched this before I started. I used the paint remover and got it on me and still had to sand :/
@essentialhandyman2 жыл бұрын
Feel free to subscribe and check back for other videos, before you start your next project. If I haven’t got a video on it, drop me a message and I’ll see what I can do for you.
@sijcalv3 жыл бұрын
that looks like an old tin of nitromors, they changed its recipe 3 years ago due to eu directive and it is now far less effective and potent than it once was.
@essentialhandyman3 жыл бұрын
It is an old tin, so that’s a great spot Bunzz. Something else they changed that is no-where near as good as it used to be… Swarfega! Thanks for watching and commenting Bunzz.
@markfinn47273 ай бұрын
👍
@essentialhandyman3 ай бұрын
Thanks for watching and commenting Mark. I hope it helped you. Please remember to subscribe to my channel and watch a few of my other videos, for more helpful advice.
@Felix_Effex2 жыл бұрын
you're angling the heat gun wrong, point it diagonally. Heat gun works best if there is varnish under the paint. Afterwards you use denatured alcohol and wire wool to remove the remainder of the varnish.
@essentialhandyman2 жыл бұрын
Thanks for watching and commenting Felix.
@hremaddox2 жыл бұрын
What coarseness of steel wool would you suggest?
@JoJo-op5xy6 күн бұрын
No mask? Is wild
@jackwardley3626 Жыл бұрын
you wouldn't use a blow torch on muntins etc i wouldn't have thought cause no matter how experienced you are your've only got to the smallest of mistakes and the glass in gone years ago when that all they had they probably sanded them by hand etc plus it would have been putty so if applied properly it would probably stayed fix in a long time more so than bloody silicone anyway worst stuff ever invented
@essentialhandyman Жыл бұрын
Putty is linseed oil based, which means it dries out fairly quickly, then cracks and needs replacing. So doesn’t last as long as you’d think. The key is very regular maintenance. Regarding the blow torch, you can use it surprisingly well on items like thin glazing beads. The glass will crack if heated too high but as long as you move the torch about and don’t point load the heat, the glass will take a bit of heat and not crack. I’ve used a blow torch on dozens, if not hundreds, of windows and only even broken a couple. Experience and time spent using the gun is key. You’ve gotta make sure the gun points away from the window when scraping with the other hand.
@pollyevhillson30892 жыл бұрын
Wtf you bunrrimg the wood lol
@essentialhandyman2 жыл бұрын
I can't deny, as it's been a few years since I burnt paint off with a low torch, I was a tad rusty with the technique. Thanks for watching and commenting Polly.
@maddierosemusic2 жыл бұрын
It sands down, and you are priming it anyway, so no harm. I've spent hundreds of hours burning paint off of buildings - so I have experience, and have burnt my share as well. Better than leaving old paint on there.
@steveridgway71362 жыл бұрын
Looks like you had 1 layer of paint on your mock up experiment. Absolutely useless comparison video if you are tackling a 1930’s house with layer on layer of paint. You forgot to clamp the test samples and then forget to wear safety goggles when dealing with nitromors!
@essentialhandyman2 жыл бұрын
I appreciate your feedback. Thanks for watching and commnting.
@TVBASICINFO2 жыл бұрын
pretty crap demo, should've used 4 separate pieces of wood
@essentialhandyman2 жыл бұрын
Thanks for watching and commenting. All suggestions gratefully received. I’ll do that next time!