This video is more detailed than any manual you can get for the transmission removal. Made my repair much much easier. Cant thank you enough for do it man 👍
@brockzayas10704 жыл бұрын
much love!
@pcsplus20117 жыл бұрын
I just replaced my CSC this past weekend with a Zspeed HD CSC, also put a Southbend stage 2 clutch, pressure plate and lightweight flywheel. The whole job took me only about 5 hours total. Love working on the Z, super easy to do anything on it!
@kaythekayak99104 жыл бұрын
How do you like the heavy duty zspeed csc? And how hard is it to replace? My csc just went out and I'm going with the z1 csc delete. I'm stil researching to see which route I go.
@lukaslenner7 жыл бұрын
Hi man!! Excellent job! I am about to do the same to my 370z. Subscribed and can't wait for next videos.
@brockzayas10707 жыл бұрын
thanks and good luck man.
@lukaslenner7 жыл бұрын
Brock have you removed starter motor and crankshaft position sensor before removing the transmission? It says in service manual to remove them but but I believe it's not needed. Appreciate your advice!
@brockzayas10707 жыл бұрын
I removed the starter but the crankshaft position sensor should not have to be removed.
@AhmedMoeTv7 жыл бұрын
When u dropping next video aha nice channel bro keep it up!
@brockzayas10707 жыл бұрын
tomorrow, and thanks bro you to!
@rtiid226 жыл бұрын
So.. that video.. 👀
@madmike4756 жыл бұрын
Brock Zayas wya
@bennguyen88777 жыл бұрын
Such a good video! loved the camera angles. you made it seem like an easy process, how long did it actually take?
@brockzayas10707 жыл бұрын
Ben Nguyen about 2 hours and thank you!!!
@brockzayas10707 жыл бұрын
like 4h.
@its.Andy15 жыл бұрын
How did you take off the top bolts of the transmission? It’s so cramped.
@Kamiidash4 жыл бұрын
DarudeOwnageZ ever get them out ? I got the top right one out with a lot of extensions but I cannot get the top left out
@its.Andy14 жыл бұрын
Legacy.mp4 used a bunch of extensions and swivel joints with a breaker bar and cheater pipe😂 beware you might end up breaking a couple of swivel joints so buy extra if you need to.
@Kamiidash4 жыл бұрын
DarudeOwnageZ I have a 24 inch extension with a deep 17 mm socket. And a swivel and then another 12 inch extension, even with my breaker bar it will not budge .
@its.Andy14 жыл бұрын
Legacy.mp4 I remember using an impact tool to do it but I advice not to use it cause you risk stripping or breaking the nut.
@giralds20164 жыл бұрын
that little white box ( gear selection ) at the top of the trans... you have any pics of the wire connector?
@brockzayas10704 жыл бұрын
no sorry!
@giralds20164 жыл бұрын
@@brockzayas1070 its alright, I already sorted it but thx
@pedrorivera73717 жыл бұрын
Great vid! Even greater that you included all the bolt sizes. Hope you make a replacement video soon
@brockzayas10707 жыл бұрын
ty bro!!!
@tonyshull80297 жыл бұрын
really good video man!
@brockzayas10707 жыл бұрын
thank you!!!!
@josealcocer007 жыл бұрын
Hey man, very informative video & it has really helped me out. I need help as i’m doing the same process on my 370z. I was wondering if you could help me out.
@TheRenegade2.7 жыл бұрын
Hey. Very good video!! Thanks
@lusciousz34935 жыл бұрын
How did you get the locktight bolts off the transmission
@kar9004 жыл бұрын
What's the name of the song towards the end of the video????
@christapia94953 жыл бұрын
That damn infamous slave cylinder from Nissan that they never fixed! 🤬. Good explanation tho, thanks!
@riz69644 жыл бұрын
How did you remove top two bolts, on the transmission?
@brockzayas10704 жыл бұрын
Lots of extensions.
@Colin_Robinson_EV5 жыл бұрын
Hope you get this message scene we are having issues removing the bell housing from the engine , All the boats have been removed everything is ready to go we have split it and 8th of an inch and it appears to be stuck on something can you Please advise any ideas thank you
@brockzayas10705 жыл бұрын
make sure all the bolts are out on the bottom. I didn't say it in my vid but you can take the shifter off its like 3 bolts and just pull it tell it comes out.
@Colin_Robinson_EV5 жыл бұрын
@@doriangibson3980 You're the dumb ass who forgot with me stupid😂
@Colin_Robinson_EV5 жыл бұрын
@@brockzayas1070 Thanks for getting back to me we actually finished and got everything put back in today and should start bleeding the clutch finally thank God
@robertoorama867 жыл бұрын
Hi my car is down so I figured why not replace the shift knob and boot cover and stuff like that so while I was taking out the oem shift knob it was hard to get out. I feel I have damaged my gearbox is there a way I can know for sure without the car running ?
@brockzayas10707 жыл бұрын
I don't know to be honest. I don't want to give you bad advice but if you do figure it out let me know. ty for watching the video!!!!
@jesusgutierrez14467 жыл бұрын
Did you hold the shaft while you where trying to remove it?
@shaolin2247 жыл бұрын
The plate is a good idea until the wind blows up ya
@kar9005 жыл бұрын
What song is that at the end?
@ThisIsIsharSingh7 жыл бұрын
why did you take out the transmission bro?
@brockzayas10707 жыл бұрын
my slave cylinder went out. stay tuned for next video, you will see me install it!!!!
@zelllers7 жыл бұрын
Are you putting in another OEM CSC? I know there's a few aftermarket slaves you can get which are apparently longer lasting, and Z1 motorsports actually has a CSC elimination kit which brings the slave external to the transmission to make it easier to replace.
@brockzayas10707 жыл бұрын
I actually have that one right now and I don't like it because of how aggressive and hard it is to daly drive.
@madmike4756 жыл бұрын
Brock Zayas where r you
@timsworld93426 жыл бұрын
I daily drive mine and its so easy i look forward to going anywere just cause i know its going to be an amazing drive to get there!
@ryanlopez46996 жыл бұрын
How do you remove those zip tie clips
@AlphaMatt10006 жыл бұрын
I'd probably use tin snips and just cut them off
@waugy370z84 жыл бұрын
Ive noticed I could damn near take my entire Z apart with a 10mm 😆