How to Test a Wheel Speed Sensor with a Multi Meter

Рет қаралды 108,771

Жыл бұрын

How to test if a wheel speed sensor is good or bad with a multi meter.
www.backyardmechanic.org
By using this information user assumes all risk of use.
See About Page for Disclaimer.

Пікірлер: 51

@dksob81 6 ай бұрын

To be clear, if specification is within 1% (as you stated), you are indeed out of spec. You have a reading of 31.11megOhm (31.11 millions ohms) 1% of that would be .3111. Therefore you spec would be 30.8m - 31.42megohms. Your reading on the second sensor was 31.58 which is outside of your specification.

@DiegoMendoza-w5w 9 күн бұрын

Amazing video and energy! Helped a lot

@danielrivera5858 3 ай бұрын

Thank you thats much better than the last video I wasted time with someone else try to tell me I need an autel computer probably a 3 thousand dollar computer would be nice to have but if I could afford that kind of equipment I would have to be here researching how to right thanks I do have an ohm meter much thanks

@polosavage1 11 ай бұрын

Just so everyone knows, he is not plugged into the car's electrical system wiring harness he is plugged into the other end of the speed sensor one and is connected at the wheel hub that has the actual sensor and the other end that he's plugged into is the end that would normally connect to the cars wiring harness oh, there are so many comments of everyone claiming he's plugged into that cars computer and the cars wiring harness and I tried to respond to all the comments that said that to let them know that they are wrong and to help them understand what's going on, so I hope this helps everyone understand what's going on here, the wheel speed sensor has two ends at one end is the sensor that's plugged into the Hub and the other end is what he is plugged into and that is the end that you would Connect into the cars wiring harness, I hope this helps I've try to make it as clear as possible

@flippy4605 7 ай бұрын

More periods would help lol

@danielrivera5858 3 ай бұрын

Some people start talking before the brain starts working you clearly see the man has the sensor plug in his hand not plugged in to the car harness

@polosavage1 3 ай бұрын

@@danielrivera5858 clearly I see that people come to these videos not knowing what to do or what they're doing so they're looking at it as an educational purpose that's where I'm coming from because he clearly doesn't describe that, you can't assume everybody knows what they're doing because they don't, clearly your brain isn't turned on enough to figure that out, I'm just trying to help people understand what's going on unlike you who's just out to instigate trouble and problems

@polosavage1 3 ай бұрын

@@flippy4605 periods are overrated LOL...............and for women!!

@aGentleman240 9 ай бұрын

Thank you

@lsearls2 Ай бұрын

Very helpful tka

@Sinister_187 7 ай бұрын

If 1 is damaged can it cause the car not to shift down ?

@izakuikichannel 6 ай бұрын

Yes❤

@ianjaeger4178 5 ай бұрын

Yeah is there a polarity difference or doesn't it matter it whichever way you hook it up I'm an Africa with this car and a mechanic cut the stupid wires and then he destroyed it out of the hub I had to order new wheel sensors so now I have no plug because he cut it and he threw the plug away Now I'm just wiring it connected together does polarity make a difference blue wire yellow wire whatever it is

@michealknight9303 2 күн бұрын

So i have my meter set at ohms with an alarm beep. Not touching them together starts it at 1. When i try to check the sensor nothing happens, it stays at 1. Is that bad. It seems like it should register something.

@michaellarcom 18 күн бұрын

My son has a 2014 nuke and the right rear speed sensor is not picking up so he replaced the wheel bearing and speed sensor and still no signal so he which the thing drives side to the passenger side and still nothing. Took sensor off and replaced it and still nothing. He took to dealer and they said ABS actuator was bad 2000$ later Still no signal coming from right rear speed sensor. The gear on the cv shaft looks good but the plate ring that the sensor mounts to look rusty so I'm going to clean it up but how can I test the leads and what to look for testing something from the computer to the wheel to track the problems down maybe a bad wire somewhere

@karrischober3schober344 2 ай бұрын

My daughter has a 2019 Toyota Corolla. All the dash lights are on and the speedometer doesn't work. The only code it's reading is speed sensor. How do I know which one? And is the wheel sensor the same as a speed sensor?

@HVAC_Mechanic 2 ай бұрын

It likely is the transmission speed sensor. Research the code and it will give more information.

@ProbabilityPiglet-if6fy 7 күн бұрын

Hey thanks but I have a problem of sorts. I tested the right rear side on the JK Jeep Wrangler because my code reader is coming up with C1035. The cable is showing OL so I tested the left rear side and it shows the same thing! Does this mean that both sides are bad? I"m not sure what's going on. I switched the multi metre to voltage and both readings were around 11.35 volts. Do you have any idea what could be happening? Surely both sides are not bad, right?

@HVAC_Mechanic 7 күн бұрын

There are different types of speed sensors, so this test doesn't work every time. I should have explained this better. If this test does not work using a scan tool to test them may be a better option.

@ProbabilityPiglet-if6fy 6 күн бұрын

@@HVAC_Mechanic Thanks for the reply. I did use the scan tool (I just called it a code reader) but really appreciate you getting back to me. Cheers

@karrischober3schober344 2 ай бұрын

Can Speed sensor cause All the lights on the dash to come on and the speedometer not to work???

@HVAC_Mechanic 2 ай бұрын

Yes, that is a common symptom.

@m.n.3490 8 ай бұрын

Good video. But, what is the next test if the ABS light is on, and the speed sensor passed THIS test.

@HVAC_Mechanic 8 ай бұрын

Are you getting speed sensor codes? If so, examine the wiring and check for any other codes.

@mnalep2 8 ай бұрын

@@HVAC_Mechanic I have the ABS light on, as well as VSC OFF light, I have C0205 code = LH front sensor, and 4 more codes. I bought a new ABS sensor line, installed it, and drove my car, and all the ABS lights went off. I then ran another OBD2 scan, and suddenly the ABS light went back on, as well as the VSC OFF light and TRACTION lights. The C0205 code is back, and the others (U0123, C1223, U0124, U0126 and U0073).

@m.n.3490 7 ай бұрын

@@HVAC_Mechanic So, my ABS light went on, with codes C0205 (front LH circuit) and C1236 (foriegn matter on tip), and C1223 (ABS malfunction). I cleaned off the new sensor (there was a small dusting of metal on it) and the AS lights went off for about 1 week, Then they came back on today for about 2 minutes while driving, and got those 3 codes again. The ABS lights went off, but the codes are still there. What else can I do besides cleaning any possibly foreign matte off the ABS Sensor again?

@jimpoteet1 7 ай бұрын

02 kia rio , manual trans, speedometer quit working... seems to have just one speed sensor- on passenger side front wheel.. has 1.4 ohms no visible damage. any ideas welcome

@HVAC_Mechanic 7 ай бұрын

There is a speed sensor on the transmission that sends information to the speedometer.

@silver120mp 5 ай бұрын

Please help; the ignition needs to be on, or you have to crank the engine? ; thank you

@HVAC_Mechanic 5 ай бұрын

Testing the sensor this way uses continuity, so the key does not need to be on.

@silver120mp 5 ай бұрын

@@HVAC_Mechanic thank you very much for your reply; a brand new sensor will it show the same values; i need mine to be changed, so i brought a new , but I'm not sure if it's working properly; thank you

@HVAC_Mechanic 5 ай бұрын

Yes, they should show the same values. Also, if you have a scan tool, look for an option to test the wheel speed sensor when driving.

@glendavis3639 11 ай бұрын

One thing you failed to consider… if one is 40 and one is 30 which one is the bad one

@HVAC_Mechanic 11 ай бұрын

The wheel speed sensor that has no code will be the good one.

@bobert8125 11 ай бұрын

@@HVAC_Mechanicbut it was plugged into the lead coming from the car not the sensor...

@polosavage1 11 ай бұрын

@@bobert8125 no he is plugged into the other end of the speed sensor, the end that he is testing is what plugs into the car's electrical harness, so he is not plugged into the car's electrical system, he is literally just testing the speed sensor, the end that he is plugged into clips into a female connector that is wired into the entire cars wiring harness and electrical system, so basically he just disconnected the speed sensor from the car's electrical system and then plugged leads into the end of the speed sensor that would connect to the car if it was plugged in

@GrimReaping 9 ай бұрын

He said exactly what to do. Look up what the normal ohm reading for that vehicle's speed sensors are. If you cant find it, most that ive worked on have one speed sensor per wheel. Test all 4 of them while youre at it.

@damespray1492 7 ай бұрын

The one with least value

@widtrak77 11 ай бұрын

It looks like you have it plugged into the car harness not the sensor leads🤷‍♂️

@polosavage1 11 ай бұрын

No he is plugged into the other end of the speed sensor, he unplugged the sensor from the car's electrical system wire harness and then connected his multimeter to the end of the speed sensor that would normally plug into the female port of the cars wiring harness, so he is just testing the speed sensor, so one end of the speed sensor is the sensor itself connected to the wheel hub and the other end of that sensor is what he is plugged into, he is not plugged into the car's wiring harness, she has his leads connected to the end that would be plugged into the car's wiring harness

@widtrak77 11 ай бұрын

@@polosavage1 ok, just confirming because it looks deceiving in the video. My hub sensor pigtails are much shorter

@MrGerryoc 20 күн бұрын

You shouldn’t be working on your car without some type of scanner. You can buy them now for 20 bucks and up.

@fillupread 8 ай бұрын

Nope. The PCM and ABS module looks Hz from an AC current, not resistance. ABS sensors are nothing more than a magnetic pickup that creates a hall effect. Probe the terminals, put your meter on AC volts and spin the wheel.

@HVAC_Mechanic 8 ай бұрын

A resistance test is a common way to test wheel speed sensors. You can also jack up the wheel, spin the tire, and check AC voltage.

@eugenemcardle117 4 ай бұрын

I have a Zafira B with ABS light and traction control lights on all the time. Today did an Ohms test on all 4 sensors using the lead coming out of the hubs. To test the feed wire to the hubs I switched on ignition and set multi meter to read volts and got = to battery voltage on all the feed leads. Now I expect next test will be check feed from ABS module to ECU as I expect it is the ECU that is sending an error resulting in the above dash lights being on. Correct me if I am wrong.@@HVAC_Mechanic

@bobert8125 11 ай бұрын

So how can you say the actual sensor is good? This is just confirming theres a connection coming from the computer. This cant tell you if the actual sensor is working tho.

@HVAC_Mechanic 11 ай бұрын

This test is not connected to the computer, it tests the sensor only.

@polosavage1 11 ай бұрын

He's got the multimeter leads plugged into the other end of the wheel sensor, not into the cars wiring harness the end that he is testing is what plugs into the cars electrical system

@kalebhinton6330 8 ай бұрын

@HVAC_Mechanic how can I test the wire coming from the truck. I have a C0035-04 and a U0422-71. Brand new hub and sensor. Ohms read good for the sensors. I just to check where the wire is broke/pinched. I'm thinking it's right behind the plug in the vehicle because there is a bend.