Damn this was more complicated than I thought. Good thing you made this video as a reference. Thank you! :)
@Speeddemon310 ай бұрын
Thank you so much for this video! Very clear instructions for testing! It's channels like this that keep us DIYers up and running. Thank you again!
@saleemkader21263 жыл бұрын
Thanks alot fixed mine by watching your video. Its ok for rich people they give it to mower repair man but for people like me we appreciate your help. thankyou again please make more videos, nicely explained,
@jonbrown631611 ай бұрын
I bought this to use as my ignition switch on a 1963 Bolens 800 riding mower kzbin.infoUgkxaAnMgzTZ_djF6K1Kr3MGiW_XGUMfUP8n I repowered with a 13hp Predator engine. Worked great! On the back of this switch are 5 terminals labeled G, M, L, S, and B. The G was wired straight to ground, The S was wired from the back of the switch to my starter solenoid. The L is for any accessories, so I ran it from the L terminal to a rear light I have on the riding mower. M is for the coil, so I plugged the stock coil wire to this wire terminal. The B is for constant battery power, so this was wired to the positive battery cable. I turn the key, first click is the accessory position, and my rear light came on as expected. Turned the key all the way and Vroom...the engine started. Turn it back to the off position, and the engine turned off. Perfect! Hope this helps!
@KeithJamesDesigns5 ай бұрын
Thanks for the video. Really helped me troubleshoot my mower. Turned out to be the blade interlock.
@gregoloskey60072 жыл бұрын
A very nice well prepared and clear video. Thanks!
@TOAD74642 жыл бұрын
I'm teaching my boy and you made me look like I know what I'm talking about. Thank you
@dpinkney692 жыл бұрын
Excellent video, thank you for sharing!
@tisco412 жыл бұрын
PROBLEM! I followed your great directions and my key switch tests good. The starter solenoid is new but does not click when I turn to "Start". If I turn the key to "Run", the only way I can start the engine is to jump from the battery to the starter. The engine runs fine until I turn the key to "stop". Then the engine hesitates but won't stop. I need to disconnect the plug wires to stop the engine. I WOULD REALLY APPRECIATE HELP. Thanks!
@vamhot952 жыл бұрын
I have a similar problem with my 2003 cub cadet lg1050. It started once with the new solenoid, ran great, backfired when turned off but it won't key start again/no click. I've ckd wire continuity all seem fine. I must be missing something. Any ideas would be appreciated.
@hammohammbbyblksheep42515 ай бұрын
I'm having same problem?
@eeledahc Жыл бұрын
I took mine apart because the lights weren't working. Man what a headache. Should have marked the pieces with a line when I pulled them out. Loaded with white grease and couldn't tell what Was what until I cleaned it and forgot how it came out. Your video help me figure it by ohming. Thanks
@ezza2002 жыл бұрын
A great video - really helpfull. Thanks
@joevonderheide4356 Жыл бұрын
Thanks. Great info. I have a eX mark quest with a plastic 5 terminal switch w/o any letters. Would you tell me how to test for connections. Very frustrating. I cannot tell where ground , solenoid, battery etc. are. Thank you
@Foof50 Жыл бұрын
On the plug side should any of them get continuity when checked against the ground plug?
@bigj64052 ай бұрын
My key switch on a Husqvarna zero-turn has a shortage
@chouyang4924 Жыл бұрын
Very well explanations, thank you very much.
@stuestrade7494 Жыл бұрын
On my Snapper RER ignition switch, I have B S M A B which may be same as the metal one you referenced in a prior video like the MTD (last) one you only showed here. What is that link? The A and B is for?
@jesseknust449610 ай бұрын
This was so beyond helpful
@wallyyuriy89125 күн бұрын
Trying to pin down why my 0 turn jd won’t start. It’s got 6 prongs. G M B ? G And sixth one unmarked as well. Why is there two grounds
@manu_9610 ай бұрын
Hi, great video. If you want to connect an hour meter to my lawn tractor, which only starts when it is turned on, what positive wire should I connect to? I have the block with the lights. Thank you
@levoniust3 ай бұрын
At least on mine, the lights are hooked up to the alternator and only turn on when the alternator is running. You will need a very good voltage regulator but that would be my bet for most accurate engine running time.
@ericbilderback13853 жыл бұрын
Thanks so much great video
@MrDanrob62Ай бұрын
I replaced a switch that had the headlight switch with one that had the reverse override position and it blew the main fuse on the mower. Does that even make sense? After two fuses I put the other switch back on it and it doesn't blow the fuse. I tested the switch that blew the fuses and in the on position it only connects B to A1. In my mind it would have to be connecting B to something else like M or G in order for that to happen. The switch with the headlight position works and doesn't blow the fuse. Am I missing something here?
@Me-gy2tg2 жыл бұрын
Thanks for the video! what does the A1 port do? 2nd diagram, I have continuity on (start b&a1) but not on (run b&a1) mower cranks and then dies when let off the key, if i wiggle or keep holding the key it will run for a minute and then eventually die..
@metalinmotionshop2 жыл бұрын
Im not sure what mower you have but it may be running the after backfire solenoid on the carb. That’s why it dies when you let off due to it cutting power to that solenoid.
@Me-gy2tg2 жыл бұрын
@@metalinmotionshop Thanks, that makes sense. I hear that solenoid click right before engine turns, but without b&a1 in run working, it may kill power to that. it a Craftsman YT3000 917289341
@Me-gy2tg2 жыл бұрын
@@metalinmotionshop Finally received the ignition switch, swapped them out, and it's running perfectly now. Thanks for the help
@michaelevans63703 жыл бұрын
My multimeter has no sound. Might you tell me what I can expect from the readout when testing the last Husqvarna switch ? Thank You.
@michaellocy49 Жыл бұрын
Me too. What's the answer?
@dougbough1599 Жыл бұрын
Your videos are very helpful. Just bought a china made off,on, start key switch ,with no wiring diagram. I'm 72 years old ,and im making a snapper rider into a mobility scooter. How can I get a diagram? 7:15
@brandonyoung77602 жыл бұрын
My A2 + L isn't getting a beep at all on the run position but does on the reverse position. What does that mean?
@danielwentworth58512 жыл бұрын
Mine also...
@LMudfoot3 жыл бұрын
would you tell me the model # of the Klein tester u are using in this video please. Great video.
@metalinmotionshop3 жыл бұрын
Its the CL390. 400 amp AC and DC.
@LMudfoot3 жыл бұрын
@@metalinmotionshop Thank you very much for the very well done video & the information. Have a great day,
@zouhairsuleiman2093 жыл бұрын
Thank you
@MrSmurfnanne10 ай бұрын
Thanks for the video...
@hammohammbbyblksheep42515 ай бұрын
Hey could someone please tell me what are A1 and A2 used for and what does it usually run to??
@metalinmotionshop5 ай бұрын
They are different between mower brands but usually it’s usually the charging system or headlights. Also the carburetor after backfire solenoid often runs through A1 or A2.
@hammohammbbyblksheep42515 ай бұрын
its a cub cadet rzt 54 2009 . i have the 7 prong ignition switch the over ride one. every letter on his is how mines is
@hammohammbbyblksheep42515 ай бұрын
Is l for lights and if so what color wire if I don't have lights?
@paulpryborowski8493 Жыл бұрын
Could you explain would be the symptoms of a bad switch.
@metalinmotionshop Жыл бұрын
Symptoms I’ve seen are: You have to wiggle the key in the start position to get the engine to crank. You have to wiggle the key in the off position to get the engine to turn off. Sometimes you won’t have certain accessories getting power when they should. On some models your battery charging can be affected by a bad key switch.
@bobcat390510 ай бұрын
Also would the hour meter staying on while in the stop position be a bad switch? And what does the Icon for the running position actually represent? Dumb question but I cant make sense of what the design is supposed to represent. Thanks Cheers!@@metalinmotionshop
@aaviator Жыл бұрын
Excellent Video...Thanks...maybe go just a tad slower next time!
@thornbush172 жыл бұрын
Dam dude, you go way too fast to follow you. Show what leads you are touching to the camera. Thank you tbo for the info.
@georgekershner662622 сағат бұрын
Seriously,slow down!!!!
@crdirtrider8562 жыл бұрын
Dude.... Wayy too quick lol... If you could just do this at half speed that would be great
@crdirtrider8562 жыл бұрын
Actually after running through all these tests 20 times, the switch turns out to be good. Still it will only crank when I jump the solenoid...