How to test whether your alarm condition on your electric fence is indicating a problem with your fence or whether it is your energizer that is broken
Пікірлер: 35
@collenmbewe46963 жыл бұрын
This is very good. Am a installer I like to learn more. Good innovation
@rizaanjappie4 жыл бұрын
Thanks for this im going to test my Energizer tomorrow
@mfundompofu71243 жыл бұрын
Hi Thanks for the Video. I tested and my energizer is fine, meaning the issue is on my fence. What do I do to fix that? Do I change the live cables?
@balookahify4 жыл бұрын
hello my system gives me a headache cause whenever i connect to the fence connecter the alarm goes off looked and fixed the fence but the continue what to do now please advice
@user-ym7sm7qd2cАй бұрын
Why is the service light and alarm light blinking
@zaga95602 жыл бұрын
How do you clear the service alarm - battery is good. Fence wiring is good.
@EmmanuelAyeniTV Жыл бұрын
Is this done with battery only or with mains connected ?
@sly67142 жыл бұрын
Hi There, please help just swop out battery after a power surge, it comes on fence works but no power going to battery so it will run down but not charging.
@mrstevemoyo67773 жыл бұрын
Thanks Mr fence for the inform
@user-gg5tb8gn7z6 ай бұрын
What happens if the alarm stays on when all the cables are disconnected?
@tiaangriessel7836 Жыл бұрын
Hi, when i connect in a loop on the live works fine, but when i switch it on on the at the wall main power it starts with the alarm, do you know what i can do?
@nccfidelity16342 жыл бұрын
Thank you so much for this videos.
@andrewryan91704 жыл бұрын
Thanks for this video, I have tested as above but for some reason, the gate light keeps flashing and setting off the alarm. This is a new unit fitted and not sure why the gate light would flash as I dont have a gate connected
@KOPPESCHAAR14 жыл бұрын
Andrew make sure on the inside where the siren and strobe light is connected, the two connections at the far right are supposed to be bridged with a smal wire in order to simulate a closed gate.
@andrewryan91704 жыл бұрын
@@KOPPESCHAAR1 thanks will check that
@bmwe30club642 жыл бұрын
@@andrewryan9170 hi did you manage to come alright? I’m having the same problem now
@Xxxcappie232 жыл бұрын
Please make move videos on electric fencing
@collenmbewe46963 жыл бұрын
How can I connect the wizard 4 to electric fence.
@yordanoshaile88244 жыл бұрын
Thanks for the video but how can I open the bottom part of wizord device
@mfundompofu71243 жыл бұрын
Torx screw driver
@freddietricia26155 жыл бұрын
how can I connect alarm system to my fence with reciever remote?
@willypittner7139 Жыл бұрын
If this is Nemtek energizer then you have to open unit with 2 Allen screws and lift cover off. At the bottom left (this is for normal wizard 4 energizer ) there is a green connector. If you pull it off you will see strobe, siren and switch connections. The switch connection has a wire jumper in connector. This is where common and no of receiver get connected. The 12v you need either to connect to 2 points on 3 point connector at middle bottom of board or alternatively take 12v from battery leads or terminals. You have to close unit again for it to work again. Hope this helps.
@user-pv3we3tc9g10 ай бұрын
If the alarm is not working what is the cause
@aronndou792410 ай бұрын
It's the fuse I had a problem too my fence was damaged but I thought it was in the box but it's not I removed all the fuses wich are three to check If they not burned but they were fine then I put back my alarm wasn't going off anymore is bcuz I put the fuses wrong or it burnt..especially the one that are close to each other wich is written battery and the other Aux both are 2A but for The Aux make sure it's 2A250V and the battery is T200mAL250V
@jacolloyd66125 жыл бұрын
Ever tried your hand at the pc board
@hamiltonjeff5583 жыл бұрын
Hello I just made my first electric fence installation. When I connect the input and the return it works perfectly but when I connect the ground wire it says and lights on the bed light. so can you help me with the loop? how can I close it with input, return, and ground?
@justelerire72883 жыл бұрын
I am in Africa I have 3 large NEMtek central which bothers me, it's kidding, it's always the same problem, please help me find a solution, I want a number or an email address to better explain the problem to you j have I. how can I reprogram the NEMtek? please helped.
@trysonchristianmujati49496 жыл бұрын
How to deal with mine which switching off on its own