How to timing Injection pump and preparation for installation for 3406B CAT ENGINE

tutorial for injection pump timing and How to install for 3406B CAT engine

[@mechanicdodz]

Sir pwedi mag tanong paano malaman Naka top number 1 sa gear. Salamat sir. Sagot

[@MachineHealer]

Sir anong makina at ilang cylinder?

[@mechanicdodz]

@@MachineHealer sir caterpillar din 3406c ang makina sir. Trouble kc nito. Palit na ako injector lahat mausok parin ng puti. Peru pag big. Lain MO ang accelerator may uso din sya ng item.

[@MachineHealer]

Sir first thing you do sir make sure yung fuel nyo malinis not contaminated ng coolant at water, and check nyo ang filter baka restricted na sya ng dirt or coolant and check your air system, at okay ang lahat Ganon padin, try to re timing your injection pump if Ganon pa din my leak ang combustion chamber mo, that's a big problem sir. Good luck and thank you for being fans.

[@mechanicdodz]

@@MachineHealer sir maraming salamat. Sir isa nalang OK lahat ang fuel line sir ma linis Namn. Sir pwedi ba late ang timing nito gawa ng Luma na. Delay na ang timing nya pwedi ba mag simulan ng usok yon sir. Thank you.

[@MachineHealer]

Advance or delay sa fuel timing sir it cause ng smoke din, dapat balance ang mixture ng air and fuel. Another cause of white smoke or blue smoke? *too much lubrication oil *misfiring or running rough *wrong fuel injection timing *worn valve guide or ring piston *failure of turbocharger oil seal.

[@olawalekazeemheavydutymech9083]

You’re a great teacher man I really enjoy the video may god bless you ❤

[@MachineHealer]

Thank you

[@hardtargettoliao1278]

Sir i salute you....mahusay ka talaga mag explain about caterpillar engine...mechanic din po ako sir kaya bilib ako sayo..keep up a good work..

[@MachineHealer]

Thank you sir

[@lonnieblackwell9215]

That guy sure knows what he is doing with that old B model cat, I sure with that had been in English. I would have liked to be able to understand what he was saying. It was still a very good video. I love the older cat engines.

[@MachineHealer]

Thank you so much. I will try to speak English for my next video..

[@johngoldsmith6629]

One problem picture is reversed. First thing he did was clean around where tool goes in to remove pump bushing and put 8H9204 felt washer in to help keep debris out. I would have just pulled all pumps out cleaned them up and put 1313719 seals on them. Check pumps and see if they needed to be lapped. Also I would have pulled plugs out back side and put updated seals. As you can tell pump is off a later engine or a reman as it has a eight bolt VTU. Also has a LI Jake switch. I use a fabricated tool and lift pump off pump bonnets. Helps keep pump straight. Cylinder pack box shows that engine is a 3ZJ or a PEEC engine that has been deleted to a manual pump. Need to use lock nuts that hold pump to front plate, just a nut can work loose. I use exhaust nuts as they have a shoulder made on them. As you can see he used a lock washer on the nut. Lock washers can break and then fall out and you have a loose nut. He then showed parts on the governor, FRC, fuel shut off and LI Jake switch. Also FTP on the bottom. Which if you rebuild the FTP, you can add a spring and get 10 psi more FTP psi. Also fuel return line fitting is a number four. I like a number six as a number four can collapse, have to update fitting in pump and tank. Pump fitting has a orifice so you have FTP psi. He puts oil on the gear, don't know why. As once VTU is installed and torqued, it's all locked together. Putting VTU on best way is get a long bolt and cut the head off. Put it in pump then slide VTU over the stud and it will line up. No need for alignment tool. Never reuse 3/8 VTU bolts. Have seen them break, get new. Now I can see VTU it is a eight bolt and a four bolt. Narrows down what engine this is. Once he put VTU on he did not push carrier back and make sure it was seated. Also thread lock is not needed on threads. He never checked his pin timing after VTU was installed. Right now I do not know if static timing is correct. Air compressor idler gear at the end. I put back cover on before I install the pump. He has stub shaft in and it will have to come back out to align it with studs mounted in hsg. That is what I can make out watching his video. Hope it helps.

[@elmercasipe8278]

marami ako natutunan sir.salamat i like big. engine.

[@robertc.fresnoza3211]

Thanks Bro! Ingat parati sa trabaho.

[@WaqasKhan-hp8of]

Good job 👍

[@rubenramirez4292]

I don't understand the language wish I could but I follow along. Thank you for what you share.

[@MachineHealer]

Thank you buddy, I wish I can help you someday

[@gaffarmirza7603]

Good information paray

[@khalilautos3386]

Good bro

[@oldcatmech]

Took me a few pictures of yours to realize that the picture is reversed! Because I see that the fuel system was on the wrong side, wow!! Yes, everything was reversed, once that, good video! But all your videos are shown backwards, if you could fix that it would be great!

[@janicemarimat7843]

Good jod

[@leowingarcia388]

marami nanaman ako nattunan

[@MachineHealer]

Ayus boss. Don't forget to share. Thanks.

[@royrodriguez4096]

Hi, I enjoyed your videos. I have a 1994 Peterbilt 379 with a 3406 B. Truck was running good until the turbo went out. Unfortunately the mechanic that was working on it miss diagnose the problem. The truck had lost power and was smoking real bad,,real bad. He replace all 6 fuel injectors then had me rebuild the fuel injector pump then he realized it was the turbo. After he put everything together the truck sounded like it was on steroids and still was smoking a little bit. I took it to another mechanic to check the timing and supposedly was out 2 teeth. But every time it went up a hill loaded it was lacking power. starting from the bottom off the hill it will only go to 35 or 40 max loaded 72,000 total weight. If it was driving at 65 and hit a hill it will go down to 40's. Engine sounds weak too. Any advice to what to work on. I am from Chicago west suburbs and is hard to find a mechanic that knows how to work on this older engines. Thanks Roy

[@MachineHealer]

A lotof causes why the 3406B is being weak during loaded. 1 Check all your intake hoses and your inter cooler charger maybe there's have small leaks during the engine is RPM, need to pressure your inter cooler. 2 your air filter is clogged! 3 make sure the valve adjustment is correct. =follow the 1&2 before you jump at #3 I'm 100% sure 1&2 is that the main problem, 15PSI required to test your air to air cooler

[@wazirkhan6234]

Good video please translate to English. Thanks

[@MachineHealer]

Thank you, I'll do that for my next video.

[@kenlow4028]

Can u tell me how the ring gear 1w5429 work, since is a free ring gear without any attachments to the fuel pump advance timing thanks you

[@MachineHealer]

I don't know what is the 1w5429? About 3406B CAT I'm not recommended you make advanced timing just follow the standard timing.

[@rafaeldelgado9335]

Como pongo a punto el sincronizado de la bomba de inyección estando esta ya con el perno fijador deslizado en la ranura

[@danilovillagonzalo9151]

lahat ba na caterpillar nasa kanan ang pin ng timing kung harapin mo ang makina ? at salamat

[@MachineHealer]

Meron din po sa left side.

[@rafaeldelgado9335]

Del 3406 marino

[@rafaeldelgado9335]

Seria ideal si lo tradujeran a español muy importanre clase

[@MachineHealer]

Por pabor amego, can you write English?

[@romeoporleytv2720]

Tanong lang kabayan,, ilan ang torque ng main at cylinder bolt ng 3406B, at valve adjust ng intake exhaust. Salamat kabayan.

[@MachineHealer]

Main bearing 190ft.lb Cylinder head 330ft.lb. Intake 0.015 Exhaust 0.030

[@MachineHealer]

Main bearing 190ft.lb plus 120degree

[@romeoporleytv2720]

Salamat kabayan,, pinapanood ko yong mga video mo,, at na subscribe narin kita. Dipa kc ako nakapag adjust ng ganyang msy jakob brake, yong 3306 lang na luma na nagawa ko, thanks ulit,

[@MachineHealer]

TDC #1 Intake 124 Exhaust 135 TDC #6 Intake 356 Exhaust 246

[@user-pt2gz8rj2z]

Bos poydi pala yan sa left side yan injection pump dba dapat sa rigth side yan

[@MachineHealer]

Left side po talaga sya eh

[@cornelioduhaylungsod8987]

boss magkaano ang labor charge ng mga ganyan na trabaho god po boss nice at malinaw na pag kapaliwanag

[@MachineHealer]

Boss nag re range sya ng 25k up to 45k dipende sa gagawin mo

[@cornelioduhaylungsod8987]

boss pulout lang ng injection pump sa loader magkaano labor charge kasi naputol yong bolt sa ilalim yong dalawa kailangan maibaba ang injection pump para mabunot ang kaputol

[@MachineHealer]

Boss para sakin around 6k to 13k pero dipende parin sayo yan boss. Dahil ikaw ang gagawa.

[@cornelioduhaylungsod8987]

@@MachineHealer bos yong kumatsu loader at caterpillar loader magkaiba ba ang timing sa injection pump

[@MachineHealer]

Boss kung same engine parihas lang po. Pero Alam ko ang mga 2008 pataas na model ng mga Komatsu my own engine na. Yan lang po pg kakaalam ko.

[@timcanizares5240]

Philippino?

[@MachineHealer]

Yes

[@aries3539]

Hi sir, pwede malaman po kung ano part number nung O-ring sa 16:29 . 3406 C CAT Engine po Tnx

[@MachineHealer]

Sir d ko rin alam if ano part number nyan, ni re-use ko lang yan kaya nga ako naglagay ng flange sealant kasi binalik ko lang yung Luma hehehe.

[@aries3539]

Meron po ba kayong video ng removal ng governor drive sa fuel pump ng 3406 C Cat engine. TIA

[@MachineHealer]

Wala po sir eh,.