How to use: 1 Channel DC12V Remote Control Switch with 2 button remote control

[@qiachip]

kzbin.info/www/bejne/l5mVfZ-sbLWjaNk This is our latest tutorial about this module, which introduces the principle, wiring and pairing of the module in more detail; if you have any questions, you can watch this video again; I hope it can help you solve the problem! Let everyone understand the working principle of this module better

[@Enoch_The_Gent]

Why don't these video ever show the power source

[@Trappintatts]

kzbin.info/www/bejne/h6apq3eZfs53rrM

[@maxxmasson4263]

It's simple the black wire going up is ground, the orange is power

[@bodhi-f6p]

I guess it's implied that if you are asking about a power supply you would know that you could use battery or a power supply and would know how to hook up already I guess like if we were in algebra they would assume we already know how to perform subtraction and addition

[@nazmiafiq1794]

😂 dont be too harshed​ to someone's kids😂@@bodhi-f6p

[@Gentex_Commander_2]

If I use a 12 volt battery to power the relay, will it drain my battery when not in operation?

[@qiachip]

Yes, it consumes power because its receiver is always working and ready to receive signals.

[@mikeehrmantraut6061]

Can you make a vid on how to wire it?

[@ilrichiamodellazolla]

I wanted to ask you for advice. I have connected a Normally Open electrometallic lock to this relay but I would like to add a led that lights up when the lock is not in action.

[@qiachip]

Do you want the state of the lock to be the opposite of the state of the LED you added? That is, when the lock is powered off, the LED turns on; when the lock is powered on, the LED turns off. Is that correct?

[@mr.celrak9872]

Can you show your wiring setup please

[@samspianos]

Can u show how the wiring is attached please

[@SportMaster666]

Please tell me where find a 220 volt remote control in which there is one channel but only with an independent contact. MEET that with the help of the remote control it was possible to connect the break of an independent circuit.

[@avec-zam7301]

Hallo, i have a question. Could i use this as a kill switch for my motorbike? Lets say to cut the line from the plus of the battery to store the bike when shopping or something and put the second button to start the bike from distance? I have a mecanical kill switch and at the other side a mecanical engin starter switch. I would cut the wires and pass them true this device. So that i could use the orignal swtiches when the remoute switch is on ON for the main power. Thank you

[@Sher_Evo_uk]

Hi did you use this for that in the end

[@jhebertdelacruz5437]

Does it "save" your settings so you don't have to redo the programming everytime you provide power once again?

[@qiachip]

Yes, it will save the settings. Even if the power is disconnected.

[@TheCerealHobbyist]

I got zero documentation with mine, not even what you are holding up. What are the inputs and outputs? I need a momentary switch for my garage door opener (like pushing the doorbell style button to open it).

[@qiachip]

First, you need the right wiring. The two terminals COM and NO can output the switching signal. Then you need to set the momentary working mode

[@TheCerealHobbyist]

@@qiachip I tried that, with an LED and it would not light up or flash. Positive should be com and negative to NO, correct? I don't hear the relay click, even though the red light on the board lights when I click B.

[@qiachip]

You can send a video at KZbin and give me your video link. I guess your wiring and settings are incorrect.

[@viniciuspedo7453]

Quando desernegizar o rele de acionamento, ele perde a configuração em q foi feito? Tera q configurar novamente?

[@qiachip]

Olá, não há necessidade de reconfigurar

[@wildanchannel2]

Can you help me.. My modul no reset mode.. Led always blink 3x after reset mode

[@qiachip]

Thank you for your comment. I’m glad I had the opportunity to answer your question. First we need to confirm one thing: is your receiver of our brand? Because each brand has different manufacturers, its functions are also different. Secondly, if you cannot reset, you can ask the merchant where you purchased it to ask questions, exchange goods, or even leave comments Finally, are there any problems that need to be solved after the reset? Is there another way to solve it? If it doesn’t work, you may need to buy a new one. I hope it helps you, and I look forward to your follow-up feedback.

[@wildanchannel2]

@@qiachip ok my friend thank for information.. Looks like I'll have to buy a new one

[@Chao-chao]

@@wildanchannel2 I recently purchased the same generic model. But if I want to reset (delete the RF codes) and press 8 times it doesn't do anything and doesn't reset anything. I found that to reset the device I have to press and hold the relay button for 6 seconds then the LED flashes 4 times (keep holding the button until it stops flashing, don't release when it is flashing or else it will reset and directly enter momentary mode learning) to indicate that it reset successfully.

[@rickybritish]

Hi if I don’t know how to connect them how will I know how to program them?

[@Chao-chao]

I recently purchased the same generic model. But if I want to reset (delete the RF codes) and press 8 times it doesn't do anything and doesn't reset anything. I found that to reset the device I have to press and hold the relay button for 6 seconds then the LED flashes 4 times (keep holding the button until it stops flashing, don't release when it is flashing or else it will reset and directly enter momentary mode learning) to indicate that it reset successfully.

[@qiachip]

Very good, buddy, you are very smart! From your description, I can confirm that you bought the same type, but not our product, because different manufacturers have different design logics So you have to follow his From your description, I can also know that his design is a bit unreasonable But you can still grasp it You are really great

[@zydrunasjocys3017]

Can i use this for 36v kids quad? Need this for safety , thanks

[@rusliyadyramlee5155]

I have 2 autogate door..button a for 1 door open/close..then button b for open/close 2 door..how to setting

[@qiachip]

Set Toggle Mode.

[@martincoutts6747]

Great video, the instructions supplied in the box are incomplete - your video is perfect. Thank you.

[@panamericansolutions]

I agree. Thank you very much. Your teaching is very clear.

[@malaymondal280]

Does another remote controller can on/off relay.....

[@qiachip]

Yes, as long as you can pair with the remote control, you can control it.

[@malaymondal280]

@qiachip But Sir,I want to use it in lock and bike.If it is on/off by by another remote then security will not be......

[@twicv912]

What is the wiring steps for this? Thank you

[@zaheersarwar5828]

Any ideas for a wiring diagram! I'm stuck I'm trying to use a solenoid for a door lock to work on this device ?

[@qiachip]

Zaheer Sarwar you can scroll down from this page for wiring diagram www.aliexpress.com/store/product/QIACHIP-433MHz-Universal-Wireless-Remote-Control-Switch-DC-12V-1CH-RF-Relay-Receiver-433-MHz-Receiver/3681001_32862095630.html remember to use your computer to open the link for the diagram

[@qiachip]

The more practical approach would be wiring the com with - then plug in the power source on + and - once it’s done just plug in your lock, plug in your lock + to NO and - to -

[@zaheersarwar5828]

@@qiachip excellent this has worked for me. Thank you for your help!

[@qiachip]

Zaheer Sarwar no problem, feel free to ask us anything about our products

[@alkatraz706]

@@qiachip can I power this using lower voltage like 5v??

[@andrewhughes8689]

I have two of these remote control units can I use one remote control to control both of the PCB boards as I would like to use a button for one board and use B button for another board is this possible

[@qiachip]

Yes, you can use it like this.

[@r91motorswelcome79]

I put my receiver on 24v 26v but don’t work only flashing lights but relays don’t work can u tell me what adapter you guys using or were to get power from also try battery charger 24v and did work but can’t use battery charger all the time??!

[@qiachip]

12V adapter

[@attilasz.1709]

Köszönöm! :-) Végre be tudtam állítani self-locking módba!

[@gennadiygar3344]

What is wire schema for momentary? please provide.

[@qiachip]

It is hard to type out the wire schema. But you can check out www.aliexpress.com/store/product/433Mhz-Universal-Wireless-Remote-Control-Switch-DC12V-1CH-relay-Receiver-Module-and-RF-Transmitter-433-Mhz/1456073_32716729232.html for a more detailed descriptions

[@kanewatman1]

Hi. Can be fitting to bmw car ? To stop steering 😢? Thanks

[@miguelangelharoaguilera1199]

Hola estoy instalando un modulo remoto de 12 movimientos con mando tiene conexiones a b c en cada selector y de hay quiero poner electrovalvulas de 12 v tengo que hacer algun puente??esque no me vino esquema ninguno al modulo ya le di corriente y funcionan cada uno de los selectores y manda pitido en cada uno pero le coloco el tester para ver cual tiene tension y no hace nada en el a b c

[@qiachip]

I posted a wiring diagram at this link, hope it helps you: kzbin.infocommunity

[@themisa]

Y como le hago para darle corriente para que este encendido tiene muchos cables?

[@davehackett6213]

Can this circuit board power a 12v golf trolley.

[@lockbreaker7961]

Yes, it’s most likely 12v 10a

[@leebo5555666]

How much power can it handle? Car horn?

[@andrewphillips8198]

What does the wiring look like to control two separate leds with A and B buttons? Can you show that? Thanks

[@ArturMorais]

did you get answer?

[@KAFSOLUTIONS]

Does it work with 220V garage door?

[@qiachip]

Oh, that's not right. The garage door has the function of up and down, that is, forward and reverse. If your garage door is equipped with a controller, the controller will convert the voltage to 12V or 24V . You can watch this video: kzbin.info/www/bejne/pWi2k4d4dsp0orc . If your garage door directly drives the motor, then watch this video: kzbin.info/www/bejne/e4LcfJqah9-Nhac. It is dedicated to 220V! I hope this helps you, and looking forward to your feedback.

[@KAFSOLUTIONS]

@@qiachip I think I bought the wrong switch 😞 I will buy the 2ch one 220v

[@stephenscott2951]

I have 12 v leds pre wired but I’m looking to set them up with a remote and battery power any advise?

[@suzukisamurai9362]

Can anything be done to the antenna for longer reach

[@dariusEMPEROR]

does it work with an input of 2.5A will it have an output?

[@franciscoalves5058]

can i use whitou control? i want to use with radio baofeng, wil work?

[@jesusvaca751]

Hello, is it possible to delete only one remote control?

[@qiachip]

We do not have settings in programming, because generally users only learn two remote controls, and then take them out for pairing after clearing the codes. This can avoid hidden dangers of some remote controls not being cleared.

[@jamesr.mcafee7008]

You are doing what I want to do, But I need to know the wiring to 'NO Com NC V- V+'. Can you show that????

[@SPIDERLEO81]

I just bought a receiver and transmitter exactly like yours, I have connected it to 12 volts, the wiring is exactly the same as yours, erase the existing data by pressing 8 times the learning button, but when I press the learning button and then the button of the receiver, the red light of the receiver is still on, the same occurs in any of the modes of oepración, ie the receiver does not detect the transmitter, do you think the receiver is damaged or the problem is the transmitter?

[@qiachip]

Can you give us the link where you make your purchase? Thx.

[@farasatali2646]

qiachip.com ,i have same problum how can i know my reciver or transmeter faulty.

[@farasatali2646]

I buy from ali express china.

[@qiachip]

farasat ali still, can we have the link where you’ve purchased the product from? Since our product do not usually have such problem

[@harrisoncheesman4495]

is there a small battery source I could use to hold open a servo that would work exactly the same as this but a small portable battery source?

[@qiachip]

I used a battery case with 8pcs 1.5V batteries.

[@wkroutz]

Did you try an a23 battery it's a tiny 12v battery found at any shop or supermarket

[@benjaminsaint4664]

Can I use it to enable and disable a 2 wire push switch if so how do I wire it with a 5-10 second active delay

[@qiachip]

Hello, QIACHIP 12V 1CH receiving module contains a delayed shutdown function. You only need to configure the remote control in this way to use this function. 1. Press the learn button on the receiver 8 times to reset the receiver. 2.5s delayed shutdown: press the learning button on the receiver 4 times, then press the remote control button again, the configuration is complete 3.10s delayed shutdown: press the learning button on the receiver 5 times, then press the remote control button again, the configuration is complete Function explanation: After pairing, press and hold the remote control button to keep the relay on. Starting from releasing the remote control button, the relay will close after a 5s/10s delay Purchase link ：www.amazon.com/dp/B07GJT1D1Z

[@salmakhan.5089]

What is the range of this transmitter to receiver??

[@404DisasterNotFound]

Well, first you need to know the frequency it's receiving on. You can start by stretching the coil into a straight Ground plane antenna, which will dramatically increase the distance... If you would know the frequency it receives on, than you could make on your own a big quarterwave antenna ANd place outdoor or on the roof..ooooor (And this is the most effective way, create yourself a beam antenna which is tuned on the right frequency. And you'll be able to cross miles in open territory ..... Buuuuuut I don't know on which frequency this thing transmit, so it's better to not mess with the FCC 😅

[@404DisasterNotFound]

Ok, just opened the device and it's transmitting at 433MHz UHF band, which is legal to use with a maximum power of 10 mW but it needs to have fixed antenna's, so no space for (legal) fiddling. Cheers

[@asc3designs]

Hello can I used with normal AC Adapter with 12V === 1.5 A or the 1.5 Am is to much thanks

[@anthonyjohnwoodward]

do you have a wiring diagram please?

[@qiachip]

Yes! We must to be need,you can see some wiring diagram by www.amazon.com/dp/B07GJT1D1Z?ref=myi_title_dp,so good product 😉

[@kojelautakamera4013]

Thanks a lot! The user guide didn't tell how to erase the codes. Also the programming looks so much easier when I see it in video. The guide was not very clear because it was auto translated from Chinese. This was very clear video and had nothing unnecessary but pure facts.

[@qiachip]

At the start of the video, there are code clearing guide. When we press the learning button 8 times, after the LED flashes. The code is cleared.

[@pinofiel]

Can I also use this to operate a CDI unit on a scooter?

[@qiachip]

I am not sure about this, you can try

[@sudhirgupta1354]

Sir I need this circuit where it is available

[@qiachip]

You can check out the circuit chart from www.aliexpress.com/store/product/433Mhz-Universal-Wireless-Remote-Control-Switch-DC-12V-1CH-relay-Receiver-Module-3pcs-RF-Transmitter-433/2138259_32815532310.html?gps-id=5298742&scm=1007.14677.110221.0&scm_id=1007.14677.110221.0&scm-url=1007.14677.110221.0&pvid=49524cde-48b9-4455-ba35-38a7791dd96f&spm=a2g1y.promotion-20181111.promoteRecommendProducts_6091620.31 Basically it is really simple, + - for powering the device, then connect the device you wanna control. Pair the device with a remote transmitter and you are all set.

[@farasatali2646]

qiachip.com when i push white boton red lite comes for 5second only this is going on in my reciver.

[@thekaiser4333]

Gupta - Amazon "eMylo"

[@Jcelkhouri]

What frequency is this?

[@antonbordov2876]

Огромное спасибо!!! Почему в описании товара не пишут правильные комбинации?!?!

[@qiachip]

thank you for your comment Your suggestion is worthy of recognition I will give suggestions to the product team in the future. Thank you very much

[@qiachip]

About your questions I gave feedback The product team here needs more information from you to understand what you mean. For example: What is the correct combination you are talking about? Please tell me your questions in detail when you have time, so that we can specifically solve your questions. Thank you for your feedback later

[@Tony_Bordov]

Я уже написал продавцу товара о неверной инструкции. Он, видимо, знает о проблеме и прислал мне другое видео с правильной комбинацией очищения. У продавца указано: что бы очистить код удерживайте кнопку 5 секунд, что не работает. С остальными комбинациями нажатий я разобрался. Их 8. Спасибо за наводку и поддержку 👍

[@betatechnicians]

can this be used in cars? I mean place on the ignition power/circuit line?

[@qiachip]

We would suggest not using beyond 80°C

[@betatechnicians]

qiachip.com thanks for the response but what I want to know is if it can work as a toggle switch for the ignition power line, considering that car battery supplies 12v and from 60 - 80a

[@qiachip]

Hello that would be too high for the receiver as it holds 10A power.

[@betatechnicians]

qiachip.com Ok thanks. Isn't there anyone that can work for it?

[@wkroutz]

I bet if you used a 4pin hooter relay with input output function you would be able to power up 30 to 60A power. I used a nos button through a 4 pin input output switch as a start button. Yes more wiring but effective.

[@soringigelflorean5259]

Hola! Lo he conectado al telefonillo de mi casa. Pero cuando abre hace un ruido un poco raro. Supone algun problema? Gracias!

[@Dic3.20]

Hi, this control works at 12V, but at how many amps does it support?

[@qiachip]

The input current does not need to be so high, but the output current does not exceed the 10A required on the relay.

[@Dic3.20]

@@qiachip Hi, I connected this relay to a coil with an external 12v 4 Amp battery, but after a few dozen activations and deactivations in the remote control, it heats up very much ... could it burn out?

[@qiachip]

@@Dic3.20 Not in a short time。

[@FAB1150]

Hi, I have the same relay module as you. When I try to make it learn a code I press the button 8 times, so it resets, then I press it once to activate toggle mode. when I press the remote button the light doesn't blink but it only turns off and the card doesn't learn the code. What should I do?

[@wwolf771177]

Can I wire this into a cars fuel pump wiring?

[@patricioortega4237]

Hello, can I put two DRL led bar connected to this device in parallel? Cheers.

[@qiachip]

Yes， you can.

[@patricioortega4237]

qiachip.com great! Thank you!

[@entaja]

Можно ли запрограммировать, чтобы включение происходило от длительного нажатия или от двух, трех нажатий. Т.к в кармане часто нажимается само по себе.

[@mxr4k101]

Is it possible to make a parallel connection with a normal physical switch?

[@joeKisonue]

Switches are usually in series

[@kennethlandicho7900]

What is the output of that device? Ty

[@qiachip]

12V, if you have an external power supply, you can also connect to loads with other working voltages

[@nenad8300]

when remote is close to relay everithing is ok. but when i make few steps with remote, relay change state, why that?

[@qiachip]

This shouldn't have happen, can you tell me where you purchase your receiver & remote control from?

[@burningh2o]

Can it be controlled by other remote devices without pairing them?

[@momodu6657]

Vous pouvez montrer le branchement ? merci

[@mustafas.4016]

Hello, I search a wireless relay bundle with 8 relays. But I don't know if I can configurat/learn it a new code. I your video I can see that you have learn the latch mode for one relay, but the relay group with 8 relay don't have 8 buttons to learn. Do you have a solution for me? Thx

[@qiachip]

Hi, first of all one we are not sure what type is that 8 relays so we conldn't offer any solution. But maybe you can try our 4 Channel Relay, maybe you can use twice, it probably enough to help.

[@mustafas.4016]

Do you sell 4 channel relays, where you can program all the relays individually? Do you have a video for?

[@qiachip]

Yeah. We have 4 channel relay. You can get in this link and the video is inside the page. qiachip.com/product/433mhz-universal-wireless-remote-control-switch-dc12v-4ch-relay-receiver-module-and-rf-transmitter-433-mhz-remote-controls

[@mustafas.4016]

Yeah 4 channel relay do you have but i need a 4 Channel relay, that i can individualy programm it like: for Example 1 Channel: Toggle 2 Channel: Latch 3 Channel: Momentary 4 Channel: Latch but for this i think i need 4 Bottons, that i can select the Channel which i will change the Mode. In this Video you have only 1 Botton for a Mode that all Channel use. The Solution : i take 4 x 1 Channel Relay

[@qiachip]

You can check this video, it helps what you want. kzbin.info/www/bejne/b4rFk6muoriif5Y

[@brunodedson6621]

To com um rele desse e queria liga uma mini trava soleide essa ligação e a mesma do vídeo

[@qiachip]

Do you want my circuit picture ?

[@bernardedette]

Can it work with 9v battery or 12v battery?

[@harveyadvincula6229]

Can we use it in other application except controlling led??

[@qiachip]

Hi Harvey, You can use it in any applications. The lights in the video is just a prop for how to pair the receiver and the transmitter (remote control) properly. So, feel free to use it on any way you pleased.

[@harveyadvincula6229]

qiachip.com Thanks. Im planning to use it in infrared sensor i hope it is possible.

[@BelajarOtomasi]

Real range?

[@Mightyx1jzge]

Can the receiver learn and work with car remote ? It’s same 433 MHz

[@pabloescobar7358]

Mightyx1jzge can it have u tried

[@judianroses317]

Why the device suddenly turn off without pressing remote button? Please help!

[@fabionogueira4281]

BOM DIA EU TENHO UMA AUTO ESCOLA INSTALEI NA MOTO FUNCIONOU PERFEITAMENTE MAI EM MOVIMENTO C O ALUNO APAVORAR E ACELERAR ELE NAO FUNCIONA COLOQUEI NO POS CHAVE VC PODE ME AJUDAR

[@nanditakarunaratna6326]

Excellent post. Thank you so much! Is there a setting when you click 7 times?

[@qiachip]

Yes, it will delay 20s to turn off the relay

[@VivekVorani]

Can I use 1 4-button remote to control 4 different 1-channel relays ?

[@qiachip]

Yes, you can.

[@Dendrotera1]

Hey, you have a video how to wire up this switch?

[@qiachip]

No, since the wiring is too simple, just connect the DC plug into power and the item you wish to control on the other 2 end

[@Dendrotera1]

@@qiachip yes but I don't know Which cable goes where.

[@qiachip]

@@Dendrotera1 I will try to explain here, the COM input is the switch, connect the COM input with the power input, then plugin your power source with the device you wish to control on the power input. The power input will also act as an output but connected with COM, the receiver will act as a switch which is controlled by your receiver.

[@farasatali2646]

I have same one latch with one remote,,now i have same one extra ramote to use Please let me know how can i use second remote with same reciver.thankss.

[@qiachip]

You can make the remote control the same as the first one to learn and then it can be used normally

[@cerrajero39mosca35]

Hola como le agrego más controles

[@qiachip]

Hola, una placa receptora puede almacenar 20 conjuntos de datos de control remoto. Solo necesita emparejar la placa receptora con cada control remoto para lograr múltiples controles.

[@momodu6657]

Super bien expliqué même sans parole !!! merci

[@akseliheik7893]

Can yuu make it always be on unless triggered off?

[@qiachip]

Yes, of cause you could select Mode 2 toggle, in this mode you press to turn on, and then press to turn off. Thank you ru.aliexpress.com/store/product/433Mhz-Universal-Wireless-Remote-Control-Switch-DC12V-1CH-relay-Receiver-Module-and-RF-Transmitter-433-Mhz/1456073_32716729232.html

[@smartin92]

This worked perfectly on a similar system! Thanks a bunch!

[@qiachip]

Thank you

[@anandjoshi8554]

@@qiachip RANGE ? (will it work from another room 10-15 feet away?

[@bestisthebest3452]

Ji sar ismein kaun sa tar battery ka hai aur kaun sa bulb ka please bataiye ek video jarur banaye

[@qiachip]

नमस्कार, आप एक और वीडियो देख सकते हैं, आप स्पष्ट रूप से देख सकते हैं कि कैसे वायर किया जाता है

[@qiachip]

kzbin.info/www/bejne/sKqrYYCnlr6ikK8

[@rush2124u2]

What is the power source? what type of battery does the receiver have?

[@qiachip]

Hi, input DC 12V . The receiver battery is CR2016. Thank you

[@rush2124u2]

Thanks, now to get one

[@rush2124u2]

Thanks

[@Alyam_Trampool]

Есть ещё режим таймера, 1) это 4 нажатия кнопки на реле и настройка пульта на включение на 5 секунд. 2) 5 нажатий, на 10сек.и 3) 6 нажатий кнопки реле, на 15сек. По истечении времени реле отключается автоматически. К реле можно привязать до 50-ти пультов Сбросить все пульты можно зажав кнопку на реле на 8 секунд до загорания индикатора на реле, или как в видео нажатием 8 раз на кнопку на реле. 🖐️😉

[@antonbordov2876]

У меня не сбрасывается зажатием ни на 8 секунд, ни на 5, как написано в руководстве. Только 8 нажатий

[@patriciozuniga6691]

Boa tarde, Como atuar dois reles ao mesmo tempo com a penas um botao do controle remoto?

[@qiachip]

Você pode configurar o modo de travamento automático com esse botão e os dois receptores

[@horeica]

where are all those wires going?? that is what i want to see

[@qiachip]

Hello, for your question, we have a related video, How to connect 12V 1 CH remote control switch module to 12V load, door lock switch, non-12V load kzbin.info/www/bejne/aXK6dndjiJt7r80, which introduces the wiring in detail, and we hope to solve your doubts and look forward to your follow-up feedback.

[@myprofile1923]

for what is used this?

[@casperrio.]

Mostlikely when you want a remote control for something like your ebike to turn on

[@peted3637]

Thank you! The instruction for adding a second remote worked perfect.

[@mapton1]

I only see one remote being programmed?

[@Chao-chao]

​@@mapton1 You can use the same remote button with many relays to control them with one remote. Or you can use 2 or more remotes with the same relay. To do so, for example press the relay button 2 times for toggle mode learning, then press buttonA from remoteA to save that remote button for toggle mode, and then press the relay button 2 times for toggle mode learning, and then press buttonX from remoteX to save that remote button for toggle mode and so on if you want to add a 3rd 4th remote ... By doing this you can have 2 or more remotes doing the same function (toggle mode in the example above).

[@arlannavasa7527]

Is it possible to clone 2 remotes in a 1 channel ?

[@Erkkilae27]

Hi! If you unplug the power source will the chip remember the code?

[@qiachip]

Yes, it still remembers the code.

[@Diagnosticandomijeep]

Sería mucho pedir el diagrama de instalación deseo conectar unas luces led para mí auto

[@MrAutolife]

Thanks! I bought the card after watching the video!

[@qiachip]

Thanks!

[@andreamitchell4758]

it's garbage it does not learn any RF i tried two different remotes and it won't learn any RF , i used a PT 2262 and other remotes it will not learn any of them i know they are 433MHZ and it will not learn them

[@paulk9746]

Yes, this product has been eliminated,

[@waltherdc771]

Haz un video conectando los cables

[@qiachip]

For detailed instructions on wiring please read at this link: qiachip.com/blogs/usermenu/qiachip-kr1201a-12v-1channel-receiver-instruction-manual

[@asadullahkhan7677]

can i use 6v battery?

[@qiachip]

No, but if you make a wholesale purchase, we can custom made for you.

[@BelajarOtomasi]

6vdc seri

[@valenzuela]

Any link to purchase this?

[@thekaiser4333]

If you can read, try reading the video description.

[@kanalord4134]

Sir thank you for this video, please tell me what is the maximum number of remotes we can pair with this 1CH relay receiver module ?

[@Fekillix]

I have two, so at least that amount.

[@intensacritica]

The system can have 15 remote control units, if the remote control gets more than 15 units, lose the initial remote control.

[@williamjames0]

Anyone know if it needs charging or do you put a battery connected to it?

[@kanalord4134]

@@williamjames0 The remote needs battery

[@williamjames0]

@@kanalord4134 but does the actual system?

[@akseliheik7893]

Will it loose the code if it is turned of?

[@qiachip]

Hello, it will not clear the code if it is turned off.

[@alcyon2sp]

Easily understood. i like latch mode.

[@pabloescobar7358]

Can this open cars

[@travissimpson4599]

Thank you so much for making this!😃

[@detodounpoco9716]

If I cut the electric fluid, it will erase the code

[@qiachip]

Sir, the code will not get erased even if you cut the power. Once the Receiver and the Remote control are Paired, it will always stay paired. Unless you erase the code from the receiver.

[@melplishka5978]

Sat Sri akaal my friend. I hope I spelled that right lol.

[@Fekillix]

Great tutorial! Thanks. I use mine with two remotes in the latch mode. Works great!

[@techman6431]

I want extra 6 pcs to work on one receiver unit

[@qiachip]

Yes, it's really good. There is nothing wrong with your idea. qiachip.com/collections/qiachip-remote-control/products/qiachip-10-20-pcs-kt05-433mhz-2-button-metal-remote-control-learning-code-ev1527-wireless-transmitter This link is our remote control package, you can buy a very cheap remote control price. We also have other types of cheap remote controls. If you need it, please contact our email address qiachip.com. I hope it can help you solve the problem.