How to use 150W DC-DC Boost 6A Step Up Converter Power supply Module?

[@SamsMediaCenter]

Excellent video. Very well done. Regarding voltage, I am clear that this module will reach 30v, but what about current? Let's say I have 24v 15a, what will be the current output? Will it 6a because they mentioned it as maximum. If I use 24v 5a power supply adapter like you, then I will get 30v 5a ? And how hot does it become? And will that female DC connector handle above 5a without getting hot? . I want to buy this module, but I am still undecided. My goal is 30v 15a to power up my 2.1 audio amplifier. XH-A128 160x2 + 220w These are the questions that I have. Please advise.

[@newtecpro]

Hello. It seems that this module is not suitable for you. What is important is that the output power is at least 150 watts. 30 volts 15 amps is too high. That means you should finally get 30 volts 4.5 amps from this module. If you get 30V 5A, you should use a fan to cool the heatsink.

[@ariparsi9889]

Your good teaching. Does this voltage reducer module have reverse connection protection?

[@newtecpro]

No, most of them are not protected. In any case, be careful when connecting the + and - wires so as not to damage the module

[@SalhiKing-fn2zs]

does this will charge a laptop that need 65w from a 12v battery sir thank you

[@newtecpro]

Yes, you can adjust the desired voltage, but there is a problem. You must use the charger control to stop the charging process when the battery is fully charged. Otherwise, the battery will be damaged.

[@joncamp9126]

@@newtecprohow is this done?

[@ExploreSciFi]

bro also mention about amperes and its output watt as well next time, you have meter to use thanks

[@newtecpro]

hi: Input Voltage: 12~32V DC Output Voltage: 12V~35V DC Max. Output Current: 6A Max. Input Current: 10A

[@ghstore_sby]

can I use 12v battery into 24v for ups 1200va?

[@newtecpro]

Yes, you can step up the voltage to 24 and then use it. Also, another way is: a 12V battery cannot directly replace a 24V battery** because the UPS is designed to work with a 24V system. However, you can **connect two 12V batteries in series** to achieve the required 24V. This means connecting the positive terminal of one battery to the negative terminal of the other battery.

[@amitghosh6966]

How is it called 150 watts? Do we have to change the heatsinks if we take 6 Ampere load from it?

[@newtecpro]

This converter has a maximum power of 150 watts. It depends on the received voltage. To get 150 watts, it is better to use a fan on the heatsink to do the cooling.

[@nabeelrao9666]

Can we reduce voltage with this device

[@newtecpro]

No, this module is a voltage booster and increases the input voltage. You should use this to lower the voltage. Watch this video: kzbin.info/www/bejne/qGjIaIGKpNygebM

[@gabrielconstantine7384]

I noticed you went to 36 volts, caps are rated at 35 volts. Any kind of load at that voltage will blow the caps.

[@newtecpro]

36 volts is mentioned in the datasheet, but your opinion is correct. It is better to never use more than 35 volts. More confidence

[@ernardbonny997]

Can one of these be used to regulate the voltage on a car alternator?

[@newtecpro]

What do you mean by car dynamo control? You can receive input power from the alternator and get a fixed output. Of course, the amount of amperage received must be within the range

[@user-tn1hk6zm2freedom]

No! The car alternator puts out to many amps.

[@mr.strange7002]

I have a 3s lithium battery pack to charge i used a 12v 2 amp adapter set this thing clamp it to 13 volt hook a schottky diode with the bettery bms to protect this board from reverse voltage and connected everything and turned it on but strangely the output voltage fluctuates and it makes a starnge noise i tried two of this and different adpaters but same result, I am confused what's going on

[@newtecpro]

In such cases, it is necessary to proceed step by step. First of all, you give only input from the adapter to the module directly without additional electronic parts. Then check whether the output voltage fluctuates or not?

[@mr.strange7002]

@@newtecpro yeap i did that with other loads it seems to work just fine so now i think i will tweak the feedback of my adapter and try to get around 13 volt and try with that..

[@newtecpro]

@@mr.strange7002 Please inform us of the result

[@mr.strange7002]

@@newtecpro Yeap i've done that and now it seems to work just fine i am happy that finally i can charge my batteries 😌

[@bangmomon4819]

Om. Kalau input nya 45 ampere 12 volt . Apakah step up nya akan rusak?

[@newtecpro]

It is better to get amps in the output power range. Because the IC heats up.

[@mohamedabdelaziz3553]

Works on 3.7 battery?

[@newtecpro]

no The minimum input voltage is 10V DC

[@tspltirunnelveli3303]

Hi sir I get 17volt 4amp from transformer dc out .i want 23volt 6 amp.it is said maximum 6amp will available when using this converter.is that 6amp available or not or only 4amps. please help me sir.

[@newtecpro]

Unfortunately, this converter only increases the voltage. Can't increase amps.

[@tspltirunnelveli3303]

@@newtecpro OK SIR The transformer iam using gives 4amps output.if i use this will i get 4amps output or will the amps decrease.

[@basitronics6152]

how to adjust Current?

[@newtecpro]

This module is only a voltage booster and it is not possible to adjust the current

[@RiYanto-bw3jx]

Ijin bertanya mas , bila bila tegangan sumber tidak stabil / fluktuatif ( sering naik turun) , apakah output tetap stabil ? Dan apakah bisa berpengaruh pada modul tsb ( apakah bikin tidak awet dan bisa merusak) ?

[@newtecpro]

Yes, the output is fixed. The output voltage will be exactly the same as it was set

[@MrpankajNagar]

This module Working for car battery

[@newtecpro]

Yes, because the input voltage is 10 to 32 V DC. The car voltage is between 10.5 and 16 volts. So, you can use this voltage reducing module for the car.

[@Aniyys]

How many amp their

[@newtecpro]

The output amp depends on the received voltage. Total output is 150 watts maximum.

[@mahmudihba5561]

Hanya dimonitor berubah voltasenya tapi diberi beban ngedrop , jangan beli yg seperti ini merk 05kj

[@newtecpro]

Thanks for sharing your experience

[@alexandertutacano1052]

Noes estas jodiendo?? pruebas un ventilador de 24V que consume 1W ??? prueba con algo de verdad como una tira de led de 50W un reflector de 100W haber si en verdad trabaja el modulo porque usas juguetes se supone que es de 6A usa todo su potencial

[@newtecpro]

To use full power, you must use a fan to cool the heatsinks. It is also better not to use maximum power all the time.