Using a fan blade puller fan be beneficial in saving you both time and unwanted exertion especially during the summer months. This is a hard job if it is stuck but with the right tool it's as easy as 1...2...click to watch.
Пікірлер: 32
@The13thSword2 жыл бұрын
0:45 Agree about applying lubricant & letting it soak in, but it doesn't "remove rust or contaminants", it allows some lubricant to get down between the fan collar & the motor shaft. WD-40 can work with 2-3 applications but a penetrating oil like Liquid Wrench, PB Blaster or Kroil are better at this. Also as with any puller type that uses a center bolt, it's a good idea to lube the threads on the bolt where they go into the puller housing. 2:30 "You want to hold the base of the fan blade puller as you're torqueing it down slowly." Sure, but look a little closer at the tool where the bolt goes into it. That raised rectangular part on the tool is there so you can get another wrench on there to help you hold it still.
@realestateinfonet90412 жыл бұрын
Very enlightening video! Thank you very much!
@joshwheeler948215 күн бұрын
Good video bro thank you
@lequang22964 жыл бұрын
Crystal clear Thank you LIKE clip
@robertmunguia250 Жыл бұрын
Nice! Just did one yesterday and boy it was stuck. Puller really helps.
@toupsclassroomtoupsclassro9557 Жыл бұрын
i'm not in the business and tried to hit shaft with hammer and got my thumb twice...........ended up cutting base of shaft with sawsall and then punched shaft out from reverse side with a vice and deep socket and punch.......bought the tool to have for 31 dollars on amazon and will never look back even if i never use it again
@cutabove90464 жыл бұрын
The problem with pullers is they often distort the hub and unbalance the blades as a result. Try finding a new fan blade once you discover you've unbalanced the old one on the same day. It often isn't easy. You've just taken a fifteen minute job and turned it into a couple of days. It is much safer to drill out the shaft using a pilot drill first and a larger 3/8 drill next. This releases the tension on the fan blade and it comes off easily. I use a puller as a last resort and I've got a couple of very good ones. And it takes me less time to drill out the shaft. The only expense is replacing your drills every four or five jobs.
@HoodHandyman Жыл бұрын
Your doing it backwards. What you just suggested is a last resort if this does not work!
@williamserver43323 жыл бұрын
Great video
@popsmccartney4356 жыл бұрын
Great video, would you make a video of the tools that you carry in your tool bag?
@johnhoog82794 жыл бұрын
Beats drilling out the shaft!
@stannisthemannis553523 күн бұрын
So, when I do this, the tool pulls off the shaft. I've tried finger tightening and using a wrench to tighten the set screws. The only thing I can think of is it's just too rusted and I might need to buy a new fan as well.
@bert1913Ай бұрын
Use Kroil and spray some in the set screw hole
@MrJacksspleen Жыл бұрын
I used wd40 and applied a crescent shaped ice cube to the shaft to make the diameter contract, and avoided applying the ice to the collar. Or maybe the melted ice mixing with the wd40 accelerated the lubrication process. Whatever it was, it came off with minimal effort.
@KE.T5006 жыл бұрын
Great video! Where did you buy the tool Puller?
@MoreThanMaintenance6 жыл бұрын
Amazon has it for $30. The brand is Supco. Thank you for watching! :)
@KE.T5006 жыл бұрын
Sam Thanks!
@isaiasjrc94532 жыл бұрын
We’re can I pick purchase one of those removers
@losmoore33584 ай бұрын
Where did u get the fan blade puller ?
@gowthampeketi15374 жыл бұрын
How will open this type of 5blade wing..
@kelasbajet68015 жыл бұрын
how i want to order
@djjoshua0073 жыл бұрын
what if the shaft is long AF!!!!... ? and the threads are not grabbing to pull it off ?
@kparks12122 жыл бұрын
Exactly! I see there’s not an answer, after a year☹️
@10acScottyP2 жыл бұрын
Cut the shaft off to a length the puller will fit down onto
@101mrcrazyman6 ай бұрын
@@10acScottyPwith what King Arthurs blade
@10acScottyP6 ай бұрын
@@101mrcrazymanthat would probably work but when King Arthur isn’t available I use a material cutter or a saws all 🤷🏻♂️
@buddyrye91903 жыл бұрын
Honestly, in 2021 there should be no reason that something so poorly designed exists as a universal part in the hvac industry. Just ridiculous how poor this design is.
@gowthampeketi15374 жыл бұрын
How will onen iron pedastal fan 5blade wings...company name...p n tufan,,, crompton greaves CG ,,,