Instructions on how to vent a Samsung dryer out the side. Great in small spaces where you need to get a dryer to side closer to a wall. a.co/d/fwf3bg0 **I say duct tape in the video please use metal furnace tape not duct tape**
Пікірлер: 29
@harveybergen107626 күн бұрын
Great video. Was fearing having to take dryer apart. This video made this job very easy. Took longer to put the tape on than install fittings. I opted for using metal furnace tape just to be safe.
@kimglover26984 ай бұрын
And there’s no “45” in there - it’s a 90 degree angle.
@lesteranderson3350 Жыл бұрын
LOL Duct tape you mean aluminum tape I hope, duct tape will turn into dust after time
@OsvaldArandaDiaz3 ай бұрын
Thank Marshall for your tip. I recommend aluminum tape is more riliable
@MarshallHudson113 ай бұрын
Yeah judging by the comments my next video might be how to replace duck tape in dryer with aluminum tape 😅
@OsvaldArandaDiaz3 ай бұрын
Appreciated video but remember turn off dryer electrical power and a shut off gas supply, preferaly disconnect.
@Spardo6 ай бұрын
This is by far the best and only adequate DIY instructional video about a Samsung dryer side vent kit. However, I do wish you provided a little bit more detail. For example, you took the screw off the back and did something with it inside. Discussing that step in detail, as well as where and how those tabs fit together, would really enhance this video given the limitations of what can be viewed. Thx!
@MarshallHudson116 ай бұрын
Thank you for the feedback! It really helps for the future videos. The tabs should slide together and then the screw secures them. Really wish I could have found a way to put the camera on the inside but I couldn't figure out how to get it back out.
@OU812Star69Ай бұрын
I couldn’t watch it the way it was filmed
@sghi727r7 ай бұрын
Good tutorial, thanks for taking the time to make it. As has been said, aluminum foil tape is superior, especially long term.
@bigbearoutdoors199911 ай бұрын
Metal furnace tape not duct tape it will catch fire
@perdidotree39785 ай бұрын
Hi there. How did u remove the circular hole. Ours doesn’t come proliferated. What tool would I need to use to cut a hole out? Thanks for your time and knowledge.
@MarshallHudson115 ай бұрын
You could use a dremel get a metal drill bit. I would check and make sure there is a tab that folds up inside first since that’s what’s hold the turn in place. Without it there’s a chance it could come disconnected.
@JasonJaan-c6q7 ай бұрын
Appreciate the video! Clear explanation and camera angles are really helpful!
@DemocracyDiesInDarknessАй бұрын
Thank you! Your instructions made this installation really straightforward and simple.
@tonycavaliero203710 ай бұрын
Did you cut the hole in the side of the dryer? My dryer does not have any detente or outline for a hole on the side.
@MarshallHudson1110 ай бұрын
Did not have to cut a hole there’s a knock out in both sides. You could probably drill a hole but then you’d need to make some custom tapes to hold the joints inside too.
SAMSUNG Side Vent Kit for... www.amazon.com/dp/B01FM3HGOM?ref=ppx_pop_mob_ap_share
@BobZawacki9 ай бұрын
You mention a tab but I don't understand where it is. You do a bunch of things that I don't understand with your arm in the dryer.
@fredflintstone43648 ай бұрын
That looks like one of the dumbest inventions ever.. !
@hayleydillman21546 ай бұрын
What tools did you use to punch the side hole out? I know it’s indented to make it easier but since I’ve never done anything like this before, I don’t know HOW to punch the hole out. Thanks in advance!
@MarshallHudson116 ай бұрын
I took a flat head screw driver and a hammer and just tapped it in circle motion until it comes free. I’ve seen people just take a big wack at it and it work but that makes me nervous
@davidduran41486 ай бұрын
Can you please tell me what that item was that you used to cap off the back? Do you know where I could find this item?
@MarshallHudson116 ай бұрын
It's just a cover that came with kit. Here's the link to the kit below. I couldn't find one that was sold separately but you could probably make a 4 inch PVC pipe cover work if you didn't want to get the whole thing. www.amazon.com/gp/product/B01FM3HGOM/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1
@Gale-zh6ng5 ай бұрын
I don't see the amazon link
@MarshallHudson114 ай бұрын
My apologies I just added to the description. a.co/d/fwf3bg0