Great Job! My advice to everyone watching, use gloves after applying heat, you can leave finger prints hard to get out, especially when applying black vinyl! Happy Wrapping
@HighVybeTribe4 ай бұрын
Thanx
@colin96304 жыл бұрын
Wrapping around holes/bolts/screws/whatever etc is the hardest part for me!
@StoopidGirlTV3 жыл бұрын
I just watched a guy try to hand stretch his wrap and it looked so complicated. You let the tool do the work on this one and made it look a LOT more doable and may try this with my next vehicle
@mixbhasad10 күн бұрын
Awesome work man. Earlier i was going for costly hydrodip, now will go for this as much cheaper alternative with same elegant look
@CasSpell4 жыл бұрын
My only issue when applying vinyl wrap is when i have to do corners. I often have to cut the vinyl in the corners to split it, just so i can lay it over the corners, and that usually leaves me with a gap between the vinyl or an overlap. :/
@TrunkThunderLithium Жыл бұрын
If your doing that you got to much overlay. Idea is tighten heat tighten heat for corners. Never try to cheat an do the Y split. It'll come up later an has a chance coming undone at that corner
@FirePhoenix103 Жыл бұрын
Cutting for relief tends to help but from what I've seen you only do it once you got it completely around your piece. The cut should just go up underneath the lip on the other side of your piece
@UpholdersoflightMinistryАй бұрын
@FirePhoenix103 you can cut for relief just as he did before stretching into those holes. Just ensure you have accounted for the length you need to get round the edge without cutting short. And then some... because as you hear it will shrink. If in doubt, cut even less then heat and cool then cut more as you'll knowvits not going to shrink much more.
@IvoryS20126 жыл бұрын
You did a great job and it looks professional. I’m inspired to do this to my vehicle. Thanks.
@HereWeGoNow6 жыл бұрын
Thank you, that's why I make content! Hope it helps
@mohammedfarooqui93584 жыл бұрын
Very helpful. Did my bootlid handle whilst going through your steps. My first time wrapping. I did fine, thanks to you. Much appreciated.
@HereWeGoNow4 жыл бұрын
Great to hear it helped man! Thank you
@HexifiedMusic7 жыл бұрын
Finally, a video wrapping a difficult piece. Trying to wrap the center console piece that holds the cupholder on my 2012 Mustang, the inner curve by the E-Brake is pretty intimidating so I gotta watch this lol.
@HereWeGoNow7 жыл бұрын
+HexifiedMusic hope it helps! There are a few videos on wrapping tips that helped me with this piece.
@rodgt90575 жыл бұрын
How did it go for you? I'm about to do that same piece on my 2010 Mustang
@donkeyrider3 жыл бұрын
did you ever wrap the center console ?
@kathypear25402 жыл бұрын
I’m waiting to hear the results from you. It’s been 4 years 😅 we’re still waiting!
@robertb62767 жыл бұрын
You left out the hardest part, getting that part off the car without breaking the ~50 little yellow or blue clips on the back, that ford doesn't sell separate.
@HereWeGoNow7 жыл бұрын
+Robert Baldwin haha! I didnt have too much of a hard time with it. Thought about doing a seperate video for that actually.
@dandeac19077 жыл бұрын
Robert Baldwin ford dealer doesn't but Tasca parts.com it does 20 30 cents per piece.
@robertb62767 жыл бұрын
If they do, I can't find them.
@dandeac19077 жыл бұрын
Robert Baldwin part nr. W714972-s300 bezel trim clip. Make sure u go by Year and model
@HereWeGoNow7 жыл бұрын
+dan deac very helpful! Thanks
@andrewpadgett23672 жыл бұрын
You are the first video that I’ve ever seen that actually removes the backing the right way. I was just placing my ford performance decal the other weekend and my gf was pulling straight up and I had to school her when she almost ripped the F off lol.
@lovecats7995 жыл бұрын
Great informational video! I’ll be trying to wrap the same dash style on my mustang tomorrow, it will be my very first time wrapping anything.
@HereWeGoNow5 жыл бұрын
Right on Joey! Hope it helped with your dash wrap.
@muzzaball5 жыл бұрын
Gorgeous job - can't believe the difference and how good it looks - thanks for sharing.
@HereWeGoNow5 жыл бұрын
Thank you!
@turbine63385 жыл бұрын
Never mine the clips, that was a great job and looks stunning. Thanks for your Vid, I think it will help many doing or thinking of doing a wrap
@HereWeGoNow5 жыл бұрын
Thank you!
@Geed943 жыл бұрын
I'm wrapping the air jet mask and this video helped me very much! I'd post a video next week. Thanks bro👍
@mpbapjensen30155 жыл бұрын
Just wrapped my PC case with some Faded purple foil and Carbon fiber
@HereWeGoNow5 жыл бұрын
That probably turned out pretty awesome
@wardaddy59926 жыл бұрын
Nice. Thanks. Thinking of wrapping my challengers interior. This definitely gave me the boost I needed.
@HereWeGoNow6 жыл бұрын
Awesome man! Good luck... Hope this is helpful
@bondoman2k4 жыл бұрын
Actually did this on the interior pieces of my Mini Cooper. I've been a collision tech for 43 years, but this was the first time I've ever tried wrapping. Came out pretty nice, but now after a year, the edges are coming loose. Not sure if that's from improper prep, or not enough heat to form it. I've done a few smaller projects since this, and still have the same probs. Always seems to be how to 'slit' , heat, and fold to get around curves and edges. But, You did a great job! ;)
@MrCamoman124 жыл бұрын
Not enough excess and post heating!
@polybotes9276 жыл бұрын
Thanks a lot man the other videos only showed how to wrap flat peices without any holes or anything in them this vid helped me a lot
@HereWeGoNow6 жыл бұрын
Glad to help!
@stevencoyote7466 жыл бұрын
Just did mine with vivid matte black but mine was alot thinker so it didn't good down like yours but it turned out great ty for the video give us more of wraps buddy
@HereWeGoNow6 жыл бұрын
Thanks man! I just may do that
@robertgarza52236 жыл бұрын
Awesome video. Planning on wrapping my trim in a couple days, will use this video as reference 👌
@HereWeGoNow6 жыл бұрын
+robert garza thanks! Glad it helpped
@kilokilo73474 жыл бұрын
Glad I found this video, looks clean af. My first attempt wasn’t great on the edges or the holes.now I’ll be using the techniques 👌 thanks
@HereWeGoNow4 жыл бұрын
Hope it helps man!
@marshallwilliams93206 жыл бұрын
Yea! Just what I needed! Planning on doing my 2017 GT in gloss white. It'll look great with the mods I've already done. Great job!
Great vid, the corners are always the hardest part for me.... Im gonna try your method 😀
@johnbrevard59666 жыл бұрын
Who's the Man, You're the Man. BRAVO!!!
@HereWeGoNow6 жыл бұрын
Haha thank you!
@ThEMath0ss8 ай бұрын
That was an awesome service you provided! Great job!
@jayvxr77043 жыл бұрын
I suede wrapped some trim pieces on my 2018 sonata (stock carbon fibre look) it looks great.
@eddieg3294 жыл бұрын
you say it right >>>SHOULD look like this .. awesome Job BUDDY ! gunna try on mY JEEP ! ty bro
@HereWeGoNow4 жыл бұрын
Thank you! Hope this helps eddie.
@eddieg3294 жыл бұрын
@@HereWeGoNow it sure did..ALOT ..TY AGAIN
@zigzagzoom36164 жыл бұрын
ima do this to my car hope it turn out good
@kentb81985 жыл бұрын
Can't stand fake carbon fiber, but this video was perfect! Thank you.
@HereWeGoNow5 жыл бұрын
Hope it helps! Thank you
@JoseDiaz-er4ww6 жыл бұрын
Nice and very professional job. I always wanted repair the parts of the manifolds that come in chrome appearance, but I'm lost and don't know where to get it. Some ideas and videos that can help me??? I really appreciate. Cheers.
@HereWeGoNow6 жыл бұрын
Thank you. I'd check on Amazon for chrome vinyl wrap. Should have a big selection. I really like vvivid vinyls product.
@JoseDiaz-er4ww6 жыл бұрын
@@HereWeGoNow Excellent idea!!! You know, a good friend has a Sentra 2016 and someone smashed the front grill, the situation is that it isn't broken, just the vinyl cover started to peel off and I think it could be fixed without spending hundreds of dollars.Thank you very much for the helping.
@frankmurray93536 жыл бұрын
I don't think vinyl is a good idea for a manifold that produces heat. The wrap won't last long and will peel up quicker or am I wrong? Seems like on engine parts powder coating or painting would be best.
@jdmchickkustomz94176 ай бұрын
Hey that looks really great I've been trying to learn how to wrap. I've got a tail light to do door panel pieces and wanting to do my hood
@hunterjones98225 жыл бұрын
I did this mod and it added 50+ hp to my riced out Honda...
@HereWeGoNow5 жыл бұрын
No it's only worth 23.5 hp
@funkblack5 жыл бұрын
Weight reduction brah. Now it's carbon..so it;s lighter, right?
@HereWeGoNow5 жыл бұрын
Exactly, the car feels so much quicker and nimble from all the weight loss.
@aries11745 жыл бұрын
Basically mugen spec now 😂
@davonmulder52724 жыл бұрын
Paired with the brake fluid delete it COMPLETELY changes the car bro!
@15DurangoRT6 жыл бұрын
Wow! More techno! Just what we needed!
@scorpionwins63784 жыл бұрын
Nice work! The end result is amazing. Btw you should tell your viewers to not try this with Wish vinyl wrap. That stuff is garbage.
@HereWeGoNow4 жыл бұрын
For sure! I wouldnt use anything from wish.
@theejoeylee4 жыл бұрын
Iso took the finish right off my shifter trim!
@JohnSmith-zw6tr4 жыл бұрын
Great video! Love the music and editing! You make it look easy! Great job dude!! Liked and Subscribed!!!!
@HereWeGoNow4 жыл бұрын
Thanks my man!
@juniorc60542 жыл бұрын
DAMN it came out GOOD... Thanks, I'm gonna give it a try.
@hemi34545 жыл бұрын
Correct me if I'm wrong but it appears you need just the right amount of heat and of course good quality vinyl ? It's like it almost melted around the piece and you tucked it away....done !
@HereWeGoNow5 жыл бұрын
Gotta be careful with too much heat. I melted the vinyl on another piece.
@robertschweder7105 Жыл бұрын
Awesome video man. I'm a fan
@HereWeGoNow Жыл бұрын
I appreciate it!
@DaddyBLUE90S6 жыл бұрын
I'm trying to wrap my hood vents on 2016 gt gloss black... Will try
@HereWeGoNow6 жыл бұрын
Good luck!
@tyreecepeterson39883 жыл бұрын
Omg doing mine was sooo hard cause it very curvy 🥲 took like three hours
@NickTheGREEK12166 жыл бұрын
In Automotive and motorcycles, I hate HATE fake carbon fiber!!!! With that being said, holy fuck stains Batman!!! Your shit looks factory clean!!!!! Awesome job. 👀👍🏻🇱🇷👍🏻🇱🇷⚾️👀
@HereWeGoNow6 жыл бұрын
Haha thanks man my!
@MeAndCarKeys3 жыл бұрын
Great video!!! I plan to do this also, seems like it just takes a lot of patience!!
@fludrbywest38862 жыл бұрын
Totally awesome job❣️👍🏻❣️😳😊
@HereWeGoNow2 жыл бұрын
Thank you! 😊
@stephgiles52695 жыл бұрын
Hey dude. Great wrap. I'm doing the interior of my car. Problem is, the wrap I have has a see through layer on the top too. Do i take that off or leave it on for protection? I'm not sure what it's for.
@HereWeGoNow5 жыл бұрын
Thank you! Remove it. It's just to protect it before you start wrapping. Good luck!
@sicks6six2 жыл бұрын
Did you remove the protective film on the face of the vinyl wrap before you started, A suggestion, dump the music, keep the actual sounds of the work, you might add spoken instructions later, and keep all videos as short as possible, some of these vinyl wrap videos are 30+ minutes, most people wouldn't even click on one that long, most people want videos like this 3-5 minutes long, can be done easily with editing. yours is one of the better videos. . .
@HereWeGoNow2 жыл бұрын
Thank you for the tips! Yes I removed it to avoid any additional binding it would have caused on such a relatively small rounded area.
@sethook-ro4xh5 жыл бұрын
Thumbs down if you are a real troll. He wrapped that perfect. Can't wait to give it a try.
@HereWeGoNow5 жыл бұрын
Haha...Thank you!
@adamskypixelds63904 жыл бұрын
thank you for a great video with step by step on something harder than a simple piece .. perfect finish brother
@DOF29655 жыл бұрын
Nice little video mate thanks a million very helpful👍
@HereWeGoNow5 жыл бұрын
Glad you enjoyed! hope it helps
@markdoten16365 жыл бұрын
My
@saifalmosuli84194 жыл бұрын
Nice work brother
@HereWeGoNow4 жыл бұрын
Thank you
@splxtzz25044 жыл бұрын
Looks great. I was wondering if I could use a hair dryer since I don’t have a heat gun. Would that work as well
@AlmostLastJedi3 жыл бұрын
Awesome video👌😎
@400knockout5 жыл бұрын
Thank you for this video! I've wrapped my interior trim now. I just cant work out the last corner and ruin the look of it
@ThreenaddiesRexMegistus3 жыл бұрын
Nice job! This is a handy video.
@Uniquetransition6 жыл бұрын
Great vid! Direct and simple. Thanks for showing the end process
@HereWeGoNow6 жыл бұрын
Thank you!
@BbrosAuto4 жыл бұрын
Preparing to do some wraping myself and this was helpful, so thanks! We are going to film it and share on our channel. Any suggestions where to get quality vinyl?
@HereWeGoNow4 жыл бұрын
Nice! I picked mine up in amazon. vivvid, hexis, avery are all good, just stay away from cheap chinese vinyl
@BbrosAuto4 жыл бұрын
@@HereWeGoNow Thank you! Will give it a shot.
@jplee35 жыл бұрын
Nice install! Thinking about doing this on some interior trim of our car but wondering how well it holds up on hotter days? Our interior is black leather so it can get hot inside if we park it out in the sun. Sorta worried if this will bubble or peel back in that case...
@ELEVENXVISUALS5 жыл бұрын
Jeremy Lee nope you’re good
@HereWeGoNow5 жыл бұрын
Had mine for over a year and no issues here
@ben3mar6 жыл бұрын
Thank you so much, exactly what I was looking for and was wondering about
@HereWeGoNow6 жыл бұрын
Hope it helps
@chevyhs5 жыл бұрын
I have the premium with the fake silver carbon fiber. Does that have to be removed first before laying on the vinyl overlay?
@HereWeGoNow5 жыл бұрын
Nope. This goes over the top of that
@barkyvonschnauzer2188 Жыл бұрын
Nicely done!
@oculusdrifter9261 Жыл бұрын
must of been his first time vinyl wrapping with them many bubbles in the vinyl and heating to stretch onto the rear which will pull back once installed in a warm/hot car... first rule of vinyl wrapping always cold wrap until its tight then heat stretch
@druss88453 жыл бұрын
Nice job! Gonna try this on some side panels on my bike. Any recommendations on a quality carbon fiber vinyl brand? Seems to vary wildly in price.
@DaveInBridport6 жыл бұрын
Just concerned about heat gun. Is it a paint stripping gun? Surprised it doesn't melt everything!
@SinisterSummers5 жыл бұрын
Looks awesome!
@waltercardenas7354 Жыл бұрын
Where can I purchase quality material? Good video
@taiblatiftaiblatif7242 жыл бұрын
Nice . Look awesome..
@blade0000074 жыл бұрын
great video. How is this holding out so far?
@emre01335 жыл бұрын
Thanks for this informational video!
@kathypear25402 жыл бұрын
How long did this piece take you? Awesome job btw 👏🏼
@HereWeGoNow2 жыл бұрын
Thank you! total time maybe 2hrs or so
@HYBRA900 Жыл бұрын
beware it looks easy but the true is that is very hard to use wrap you need to have a lot of experience using it... I did the same wrap to my car 2 days later with the heat of the sun the wrap started to unstick from the plastic :( Is not recommended to use wrap in places that weather is very hot.
@Sls50466 жыл бұрын
Makes me wanna carbon fiber my arm...
@HereWeGoNow6 жыл бұрын
Could look pretty dope...as long as you don't need to ever bend it.
@zaidchalabi15994 жыл бұрын
man this video is so good. im gonna do it to my truck dash. i was curious on how to do it. any idea on whats a good quality vinyl types online or it doesnt matter which type ?? thanks
@HereWeGoNow3 жыл бұрын
Thank you! I used vivvid vinyl off Amazon. Just stick to the well know companies (3m, vivvid, hexis, kmpc, ect). Metrorestyling.com is a good site as well
@davephantom4 жыл бұрын
Excellent - can you do this with a Parrot Disco?
@michaelmixon24796 жыл бұрын
Very impressive! Great job!
@HereWeGoNow6 жыл бұрын
Thank you!
@tonybelisle4236 жыл бұрын
Looks great
@HereWeGoNow6 жыл бұрын
Thank you
@ConalRF4 жыл бұрын
I bet that's nice and squeaky when you clean it too.
@Nahduge5 жыл бұрын
I'm having problems with the right angled corners. Do you overlap the vinyl? No matter how hard I try it can't be not overlapped
@15DurangoRT7 ай бұрын
What brand of vinyl do you have? It doesn't seem tacky at all.
@krazmex095 жыл бұрын
Nice video the 3 bad comments below me made me want to watch this because i knew they were wrong.
@DeadpoolyoteRed Жыл бұрын
Looks awesome what size did u purchase for the dash the 75 by 5 feet ??
@HereWeGoNow Жыл бұрын
Thanks! I think it was the 6ftx3ft. You don't need all that.much depending on the dash you are doing
@DeadpoolyoteRed Жыл бұрын
@@HereWeGoNow I’m doing same dash as u ..
@JuanManuel123ify4 жыл бұрын
Magnífico trabajo compañero....enhorabuena....
@electron10126 жыл бұрын
Looks darn good
@HereWeGoNow6 жыл бұрын
Thank ya sir!
@tesla_3_performance5 жыл бұрын
Ford mustve watched this video...the 18s/19s have this now i believe...
@reece72597 жыл бұрын
I honestly would've wrapped the interior pieces something crazy so it's more interesting day after day
@HereWeGoNow7 жыл бұрын
+Reece Schmit The nice thing is that if you ever feel the need you can always pull it off and change it up.
@Ctreygo6 жыл бұрын
Vinyl wrap cup holder
@PWS1126806 жыл бұрын
Patrick swayed
@brandonwright20676 жыл бұрын
Reece your crazy you mean like those dumb ass Honda fan boys. what he did made the car look more expensive then it really is.
@nubielperez30344 жыл бұрын
Very nice good job
@saltysoulcreations85374 жыл бұрын
nice job!!!
@HereWeGoNow4 жыл бұрын
Thank you
@jillianmathers18274 жыл бұрын
Can you link the last song that was played in this ? Great video btw :)
@1964rmcc6 жыл бұрын
Excellent job wow looks great thanks for sharing this now I have a new project Lol,hey just let me know how this stands up against the sun light if it starts to fade I installed some trim inside my vehicle but had to remove it just after one month due to fading and it was made by 3m .
@HereWeGoNow6 жыл бұрын
Mines held up well! It's not going to past for ever but no vinyl ever will. I'd expect to get 3-5 years out of it
@RCbashingtheKRATON6 жыл бұрын
awesome job bro...awesome music choice
@HereWeGoNow6 жыл бұрын
Thank you man!
@claytonschulz80324 жыл бұрын
Does the heat help the glue/adhesive stick to the piece you’re working on?
@HereWeGoNow4 жыл бұрын
It does help it adhere as well as makes the vinyl more pliable and allow it to strech
@lonniefreeman42784 жыл бұрын
Thank you for the edumication.
@jasonbuben77874 жыл бұрын
How durable is this stuff? Does it adhere good. Wanting to do this for my ac vents. Will it be bad to do that considering there will be a breeze of hot and cold air?
@michaelhuey19396 жыл бұрын
It's easy on something so flat like that, try a center console for a mk1 citroen c4 not so easy
@everydaytrev3 жыл бұрын
Can you do stuff like the silver trim around the vents and steering wheel without taking the parts off?
@ebrahyms7 жыл бұрын
nice work man keep it going
@HereWeGoNow7 жыл бұрын
+Ibrahm Kuari thanks man!
@kevinwilson87835 жыл бұрын
Nice video
@HereWeGoNow5 жыл бұрын
Thank you
@SHADOWBLACKs6507 жыл бұрын
How is your transmission? It's been one full year after the fluid change. ... Interested in knowing how that fluid is. Thanks.
@HereWeGoNow7 жыл бұрын
+09victoryrc the clunk is still gone! Happy with it
@SHADOWBLACKs6507 жыл бұрын
OK. I've been surfing around for opinions for year and I'm going to be doing it this week. ... Thank you again.
@HoustonTexxas4 жыл бұрын
Great video!!! Now it’s time for me to try this and fuck some shit up on my truck!!! 🙌
@critical_mass82794 жыл бұрын
Good video, good job. Thanks!
@getreal33362 жыл бұрын
How do you do damage the wrap when screwing into it? I wrapped a piece of trim and when I went to screw it back in, as you go to tighten it securely, it grabs, pulls and twists the vinyl and ruins what was a perfect job.