How to Wire for a New Ceiling Light | All About Lights | Ask This Old House

Ask This Old House electrician Scott Caron installs a new switch and ceiling fixture for a homeowner.
#ThisOldHouse #AskTOH
SUBSCRIBE to This Old House: bit.ly/Subscrib...
Time: 2 hours
Cost: $100
Skill Level: Expert
Tools List for Wiring a New Ceiling Light:
Oscillating saw
Pliers
Drill
Shopping List:
LED light fixture
Electrical mounting box
Electrical single gang box
Electrical wire
Wire nuts
Electric staples
Fish tape
Electrical tape
Madison bars
Light switch
Light switch cover
Steps:
1. Before doing any electrical work, always shut off power to the house at the main breaker.
2. Trace the mounting box on the ceiling where the light fixture will be mounted.
3. Cut out the traced hole with an oscillating saw.
4. Determine a location for the light switch. It should be 48” from the floor.
5. Trace the electrical box for the switch and cut it out the same way as the mounting box.
6. Locate a source of power for the switch, either at a junction box or at the main electrical panel.
7. Connect the electrical wire to your source of power using the pliers and wire nuts and fish it through the joists until it reaches the light switch. Secure the wire to the joists with electric staples.
8. Drill through the floor in the correct stud bay and send the wires for the switch and the light up to the switch using the fish tape.
9. Mount the electrical box with Madison bars in the wall and wire the switch.
10. Screw the switch into the box and then cover it with the cover plate.
11. Cut a temporary access hole in the wall and fish wires from the fixture mount in the ceiling to the temporary hole, and then from the temporary hole through the joist back down to the basement where the switch was wired.
12. Mount the electrical box in the ceiling with more Madison bars and screws.
13. Wire the new fixture in the box and mount it to the ceiling.
14. Patch the wall where the temporary hole was cut.
15. Turn the power back on.
Resources:
Scott installed the "Boxie" ceiling-mounted LED fixture, manufactured by Tech Lighting (www.techlightin....
Basic electrical items like switch boxes, ceiling boxes, 14 gauge Romex wire, and switches can be found at a home center or electrical supply house.
Expert assistance with this project was provided by Caron Electric (www.caronelectr...) and Wolfers Lighting (www.wolfers.com/).
Keywords: This Old House, How-to, home improvement, DIY, Scott Caron, electrical, Ask This Old House, repair, lighting
About This Old House TV:
This Old House is the No. 1 multimedia home enthusiast brand, offering trusted information and expert advice through award-winning television, a highly regarded magazine, and an information-driven website. This Old House and Ask This Old House are produced by This Old House Ventures, LLC and are presented on PBS by WGBH Boston.
Follow This Old House and Ask This Old House:
Facebook: bit.ly/ThisOldH...
Twitter: bit.ly/ThisOldH...
bit.ly/AskTOHTw...
Pinterest: bit.ly/ThisOldH...
Instagram: bit.ly/ThisOldH...
Tumblr: bit.ly/ThisOldH...
How to Wire for a New Ceiling Light | All About Lights | Ask This Old House
/ thisoldhouse

[@leonpse]

I wish the video showed more about the shutting down the electricity and the actual wiring done to connect things.

[@ncooty]

Next home owner installs a ceiling fan from that box.

[@psyo123]

to be honest this is dumbest light installation ever seen.

[@harrycave6309]

They are gonna get a hair cut with that roof hight if they add a fan

[@T1Oracle]

That's their problem.

[@leofitzpatrick6430]

😂😂😂😂😂

[@immortalspirit4ever1]

Haha that would suck

[@davidmarquardt2445]

Now for the first time she doesn't have to stumble through a dark room to turn the light on. A electrical feature the rest of us have enjoyed for about 70 years.

[@rebeltango]

speak for yourself! I have three light switches in my four bedroom two bathroom home. pull cords everywhere!

[@banihex]

Lmao what’s with T-Pain at 1:30

[@moelo5930]

Quite the improvement, only thing I’d change is a nicer light fixture for the space.

[@ratchet219]

Good guy, they should bring him back on the show

[@julianabramo245]

1:30 my favorite song ❤️

[@roshanr16896]

This song is actually fancy

[@fritzmortimer4129]

This is a great and informative video.

[@ahmedaljumely5552]

Something not clear?? How you the light on now ??! And you didn’t counter to the switch??

[@Bigbacon]

That beam in the basement

[@cup_and_cone]

And now the next unsuspecting homeowner who goes to replace that light fixture with a ceiling fan will end up with it on the floor when the whole junction box falls through; hopefully not on a child or pet. If you are putting in a ceiling box, please go all the way and anchor it to the rafters/beams/joists. The extra two dollars and five minutes to future proof is worth it.

[@Blox117]

thats if you are dumb enough to assume a light fixture could support a fan.

[@r1ckastl3y86]

@@Blox117 the last owners of my house decided to use a light switch box to hold the ceiling fan in my room. It really scares me to know a light switch box is holding up my ceiling fan and it can fall any day now so I am gonna be replacing it VERY soon.

[@avrahamlevy3619]

PLEASE link top light fixture!!!!!!!!!!!!!!!!!!!!!

[@michaelsteinbach]

Company called dweLED makes a similar unit (if not the same) and costs about $120+ depending on finish. Search FM-4006-27-BN on Amazon.

[@gregorall9779]

I'm so glad he isn't on the show any more. In all my years of electrical work, If I was hiring, I believe that the only place his job application would be would be in the trash can.

[@electricaf365]

Why

[@gregorall9779]

@@electricaf365 it's pure laziness to use Madison straps on an octagon. You know darn well the next home owner is going to hang a heavier light if not a ceiling fan not understanding or knowing how it's held up and I think you can figure the rest out. Should have used an old work fan box with the expanding bar.

[@electricaf365]

@@gregorall9779 wouldn’t that be the next owner’s responsibility to brace it before putting in a ceiling fan?

[@gregorall9779]

@@electricaf365 You're assuming that the next homeowner is going to be aware of how it's secured. Personally, I would want to have it done correctly, not just the cheap, easy way. I just don't care for this gentleman's work ethic. In past episodes he has performed certain tasks, that to me, seemed the quick, let's get it done mentality.

[@AmarZ4373]

1:30

[@AmarZ4373]

2:16

[@aj555541]

Her floors must be freezing 🥶

[@DaveSimkus]

Well, guess I'm not installing any new lights. Blindly trying to snake wires through walls is ridiculous.

[@igorovmaior4919]

1:31-1:41 Anyone else heard the beautiful music played by the oscillating saw?

[@johnsmith-qe2fd]

Haha awesome 👏 I was thinking the same thing....like did homeboy just make a song?

[@Engineer9736]

In a warehouse where i used to work they had a pneumatic wrench, which had a little speed lever. Could kind of play guitar on it with that aggresive pneumatics noise LOL

[@Exayevie]

It sounded like it was singing!

[@kevzz108]

Sounds like a Disney cruise horn battle

[@danieldrews9180]

Igorov Maior deadass came down here to type 😂😂😂😂😂

[@mattkrywyj5184]

My man definitely looked at it and 100% said "You got a light bulb"

[@probegt75]

I'm pretty sure the second half of this tutorial can be found on the Hub 🙃

[@r1ckastl3y86]

Lmfao

[@220avg]

I WAS THINKING THE SAME THING

[@jamedlock83]

Take a shot everytime she says "that sounds great"

[@AndyMartin51]

Not trying to die of alcohol poisoning over here

[@krishisrani6234]

@@AndyMartin51 LMAAOOOOO

[@warn3535]

Next home owner named Madison hangs a ceiling fan and realizes that thing is held up by only Madison bars..

[@KingRune]

I like how he just puts the box on the ceiling without any measuring,

[@johnames6430]

it's already been pre-marked you can see some pencil lines on there

[@thomassemich4627]

Yeah, he just happened to stick it on the ceiling and it was perfectly centered, just like that!

[@AndrewLeeW1]

@@johnames6430 i surely hope so. Id be pissed to have a light installed off center. OCD activate.

[@swss12]

good thing he checked for joists in the ceiling before he cut!!

[@matthewwong1064]

He can use a pancake box if he ends up hitting a joist.

[@anthonyvilla9254]

Matthew Wong no pancake can hold that little square he puts in last

[@lightshow6638]

Antonio villa they can

[@amandeepsingh2864]

Good video as always but don't like that he cuts through the main beam to pass wires. The beam already showing signs of wear and tear and lost strength over the years.

[@cdixon2011ify]

Wait! Was I the only one that didn't hear him say "cut the power first" especially since he stuck a screw driver in that box?????

[@nishantdole]

The way he is just snaking wires so easy I wish it was like that in real life ...

[@Arieeeee]

I bet they spent an hour or two investigating the best way. It also helps that they have basements in that part of the country. In my world, there are no basements so it's either attic or cut holes.

[@shadowblack1987]

@Abdul Rahman lmao use a battery operated closet light dumbo. They last a longggggggggggg time. I change mine once or twice a year.

[@shaunehemphill3259]

Ronan B what’s the brand/kind you use?

[@shaunehemphill3259]

Abdul Rahman lol right

[@signetulupan]

Abdul Rahman whoa

[@strangerofthe2067]

“We have.... are you ready for this?!?!? LIGHT EMITTING DIODES!!!!” Ah yes, the good old days.

[@willievihaan6643]

Instablaster

[@kenc2257]

Nice install. Never heard of "madison bars" before. We have 3 external lights that are really LED panels--we like them (though they do have an industrial/commercial look, which wouldn't suit everyone).

[@juananaya2062]

Of coarse, they did not mention this-----turn the power off before you do this. This should always be made as step 1.

[@cup_and_cone]

Nice, an electrical video! The most controversial of all TOH videos... * Grabs popcorn *

[@Jack-vm1fg]

The wall construction is unlike anything I have seen. how did he get the fish tape through the header stud at the top of the wall? Is there one? 6:10

[@famousforever8556]

All that work and using a modern LED light and you choose a crappy old obsolete toggle switch like that? Foul.

[@johnnywadd7960]

Foul of Fool?

[@La_abbess]

Johnny Wadd 😂

[@electricaf365]

Obsolete toggle switch?

[@purpleidea]

This is crap. They don't actually show you how to do the wiring properly for those that don't already know!

[@ClearWaterPumpWell]

How to install a ceiling light in a room in a house that is from the 40's. Step one make a hole in your ceiling that is probably not the center of the room or lined up with anything. Cut in a switch box anywhere on a wall and not locate the studs first. Make sure you use commercial box's with F tabs they make it really easy. Get power from just any random junction box that does not supply power to that room, which makes finding the breaker fun. Run your switch and hot wires after you make them up in a box so you can waste more wire. Don't worry about removing the switch tabs 6:04 , so on a pop-in box your plate will just stick off the wall. Don't worry about finding a way to run the switch leg through a attic or other access, just cut a hole in your wall. Use a pop-in box in your ceiling, it will hold a ceiling fan when they decide they hate the ugly light. Last thing make sure your electrician fixes the hole he cut in the drywall, you'll never notice the patch! My point is for gods sake if your going to make "How to Videos" and your a "Professional", at least do things correctly and don't leave out important details!

[@juliof970]

She's dressed just like Scott.

[@GeeTheBuilder]

Do American electricians really just find any old random junction box and take power for a lighting circuit?? In the UK we have dedicated lighting and power circuits. And a reduced current limiter (fuse) is needed if you HAVE to do this. I know Americans use radials but mixing and matching lighting and power circuits?

[@masterofnothing3373]

Not "real" electricians! :(

[@theveganvillainess]

Ok, but you didn't show us how to do the wiring in that box, not very helpful...

[@vsmit.h570]

Scott's saw was a musical instrument!

[@jeffreyrichardson]

john goffreds mothers bird shirts table doug brothers hongmeizhous lovers

[@BBQPitmaster626]

When did Steve Wilkos become an Electrician?

[@justadude3902]

I love this old house! I watched it when I was 5 and I still watch it at age 19!

[@oakmen4604]

God I feel old, same thing, watched them when I was 5 and now that I’m 30 in my first home. :p

[@cup_and_cone]

Watched as a kid, and am now in my 30's. Those were great mornings every weekend. Miss the Yankee Workshop too.

[@bobbywilliams2471]

@nick sawv same here except i am in my 20s

[@techmetal2292]

Same here

[@jackalanjones9635]

Nick Sawv same but I'm ten

[@docz2010]

It will be nice when the NEW owner of the house installs a ceiling fan on the box, lol. Nightmare -

[@illestofdemall13]

Before installing a fan, you are supposed to make sure the box is fan rated. It would be the owner's fault if he/she installed a fan onto the wrong type of box. If you don't know how to do it properly, then you hire someone who does.

[@johnholfelder6724]

Kris Klekosky Good advice, but how many homeowners think they can save a few bucks by doing it themselves. It’s just white to white/black to black, and just screw in a fixture. I once came across a ceiling fan screwed into a lathe and plaster ceiling with no junction box. The splices were just hidden under the cowling. I took it down and refused to do the job.

[@SD-yb5fx]

Why not make sure that you are truly saved by Jesus Christ and practice this way. Remorsefully confess with your heart your sins to Jesus Christ who is God and tell Him that you right now are repenting of your sins and you want to be born again of the Spirit from above. Tell Jesus that you are remorsefully sorry for breaking His commandments and that you are begging for forgiveness from Him. Allow His blood from the cross to wash away your sins. After this is done with your heart successfully the Holy Spirit will come to live within you and He will rebuild you from the inside out. Look for signs that you are saved. Things like spreading the good news from Jesus, getting other people saved, a craving for the word of God, reading the Bible, etc… These things are known as a calling and fruit bearing. If you're not bearing fruit then keep doing it. Sometimes it takes time to get saved. Read Matthew chapter 13 from the King James Bible. God bless!!!

[@nicholasd7731]

Next homeowner installs a second switch because they forgot one by the kitchen so a new 2 new switches for dimmer and so ten they don't have to walk there.

[@danielkofman4592]

Why not just use a remodel box? AKA Cut in Box. Ive never used one of those Madison bars he showed

[@johnholfelder6724]

daniel kofman I’ve used them for the switch box, but never for a light fixture , even one of those lightweight LED fixtures. Whenever possible, I’ve always used a fan box to mount overhead lights. You never know if someone will want to change out a fixture

[@razorcool5011]

How will The next homeowners put up a ceiling fan the box is just gonna come right out along with the fan

[@jackflackatari]

This guy ever hear of a Stud Finder. I never attach electrical boxes to Sheetrock. Wait tell someone goes to install a ceiling fan. Or the light switch wiggles loose after a few years. Do it right the first time.

[@CupidFromKentucky]

Eh. I would use them for a light switch. But never for something that hangs from the ceiling. I always try to attach ceiling boxes to structure.

[@masterofnothing3373]

I concur with the issue about the ceiling box; but, he should have used old work box for the switch. Those don't generally come loose because the brace is part of the box and screwed in at installation.

[@illestofdemall13]

Sometimes the light needs to go into a place where there is no beam, and the light fixture is also not heavy. I like to use the plastic blue round cut in boxes for light weight applications.

[@xworkerbee]

Pro Tips: NEVER use a power tool to cut blindly into sheetrock. You could easily cut through a concealed wire. Instead, use a hand held keyhole saw. Also, do not use those metal boxes with those flimsy metal mounting straps. It is much better to use "old work" plastic boxes that will mount securely to the sheetrock. .

[@Vanilla_Icecream1231]

No always use metal boxes for fans but using f clips for ceiling box is dumb cause some one who don’t know could install a fan there so either find a stud and screw ur box onto that or use the box I forget what it’s called where you can unscrew the side to bit it in the wood

[@matthewnowak3488]

That’s not always the case, here in Chicago Romex isn’t allowed nor are plastic boxes and we run into more plaster than drywall, so everything has to be metal, the Madison hangers are ok for switches but we don’t use them for outlets, we use a metal box with expanding ears. I do certainly wish we could use Romex as it would be soooo much easier but it’s not Chicago code.

[@chrisburns5691]

those oscillating saws have about as much chance of cutting something as a jab saw. Actually less of a chance as you don't need to go as far into the wall. His method was just fine.

[@AStanton1966]

@@chrisburns5691 I agree with you. As a homeowner, I just used an oscillating saw to do some old work in my house for the first time. Those saws give you a great amount of control to stay within the lines.

[@chrisburns5691]

@@AStanton1966 I have used one routinely at work for years for this purpose, never an issue.

[@Rewster68]

Mike Holmes would have gutted the entire house.

[@carolinaeric8500]

Shannon Lawson No, that would be Matt Riser lol

[@notafanboy250]

lmfao!

[@rtperrett]

This Old House ceiling looks so low.

[@jeffreyrichardson]

a drivers needed geralds rogaine hair seeded hongmeizhou greeted

[@anjanm1007]

"I love it - how do I get it up" - lady -- LOL love it! (1:15)

[@horologie]

are you 9 years old?

[@technicalsteak841]

He ain't no lady. And I am not talking about Scott.

[@selcukipek3075]

😀

[@ShakespeareCafe]

Part ll Repairing drywall hole with hot mud

[@sonconmas]

As a UK electrician I can't believe how different things are done in the US.

[@AMD1]

This guy is a hack. Not a good representation of north american electrical systems at all. It's my understanding that plumbing is vastly different, too. I'm baffled by the complexity of uk toilets, especially the old ones.

[@robertahart5160]

@@AMD1 a hack lol???? The only thing I would have done differently is use plastic old work boxes. Otherwise there's 0 difference.

[@sairamnagarajan]

I’m curious- how exactly would you say they are different?

[@RefuseToLoseCanada]

Wowweeowe

[@DIY_Tips]

Great youtube channel my friend 👏🏻😊

[@richardmesser1091]

Dimmer switch would have been nice

[@crankbait09]

question: I noticed he used the metal box with that madison bar. Why not use an existing work box that has the self tightening levers already included? I imagine their was a reason for the route he went when he chose that option.

[@Vanilla_Icecream1231]

Tbh not really like In Canada we only use metal boxes but use it f clips was dumb for the wall it doesn’t matter but using f clips for the room was dumb

[@williamlewis3965]

I have never heard of Madison bars but I have used thousend of " F" clips

[@JamesDalphond]

They are called battleships around my parts.

[@sarahgrace8798]

C clips in Australia

[@marksanders768]

Wow. Thanks for skipping the entire process of connecting power to the light. "Here's a junction box. Aaaand that's all there is to it!" ????

[@youtubeaholic2154]

I've gotten used to plastic remodel boxes with fold out ears.

[@scarroll625]

KZbinaholic2 they are called old work boxes

[@kevinsmith3851]

The alluring shadow terminally invite because twig contemporaneously jog barring a cute washer. ambitious, watery dog

[@bbraat]

I don't like those LED lights. The downward pointing light made it look like an interrogation. I tried two and got rid of them both and went for a hanging fixture. Although, this woman has a lower ceiling than I do so I can see she'd want to keep it more flush.

[@ja8898]

I have some old work boxes with built in tabs. You just twist them with a screwdriver and the ears pin it to the drywall. No need for the madison bars.

[@matthewkenney8915]

I've seen better acting on the Hub

[@AnonyMous-lk7zi]

Imma go with white to white, black to black, ground to ground. What's a concept.

[@dwaynemcknight9524]

U never showed where the wire got power from to the ceilings

[@electricaf365]

He did at 3:02

[@jacqjacq5920]

This was so good to watch. Just what I was looking for! Thanks!

[@paulrreeder]

why didn't he use Old Work Box and Round Old Work Ceiling Box

[@jayv2765]

You have to use metal old work boxes for commercial electrical work, maybe its what he had in the truck.

[@KitchenerLeslie2]

He did.

[@paulrreeder]

John Kurkowski no he didn't that residents not commercial there a big different

[@techmetal2292]

Probably what he had with him

[@MountaineerOutdoors]

not sure if the electrical junction box in the basement had it or not couldnt see it well in the video but It def needs to be grounded and by code the screw in the switch box should have been green and a separate wire not the wire off the romex. And just my opinion but always put a ceiling box rated for a fan up because if they get tired of that light and want a ceiling fan its def not gonna hold.

[@mattbartolovich8228]

I would have put in a rafter bar

[@mattbartolovich8228]

Fan hanger

[@futbol1972]

Hello I bought 2 led lights that have a short cord that can be plug in outlet with on and off switch, but it also comes with cable that can be wired. It's nice that this can be plug in outlet and haclve an on and off switch. The problem is that cord is only 2 ft long. I have a ceiling fan with light in garage. I control it with light switch from inside house. If I decide to wire the two new led lights can i tap it from ceiling fan? That way when I flip light switch on it will turn on ceiling fun and new led lights too? Do I have to get into attic to do this?

[@opentrunk]

My house is actually insulated and the tops of my walls have something called a top plate in them.

[@compactcow]

I'm assuming above this light was another floor, otherwise they could've ran the wire from the attic.

[@matthewnowak3488]

Again I see this! Put a fricken fan rated box to the structure, it’s code for us here why does he do this!

[@purplekillerpenguin]

Is there no regulation in the US to how much weight a ceiling fixture must hold? In Europe its 25kgs

[@Vanilla_Icecream1231]

seymour butz yeah there is I’m not sure how much but if your installing a fan or heavy light you have to screw a metal box not plastic to the studs so the fan or heavy light won’t fall

[@illestofdemall13]

They make different junction boxes for different things. They make heavier duty metal ones that support up to a 75 lb fan, for instance. It depends on the application.

[@mrsavedbygrace2569]

Gotta be nice to be like a baby giraffe and just reach up to work on the ceiling.

[@EDHBlvd]

I need to buy some Madison bars...

[@electricianron_New_Jersey]

Madison bars are so old school. I am a pro and do still keep them on my truck but only for when I need them, like with BX cable. I mice prefer to work with plastic old work boxes.

[@Faddnn]

@@electricianron_New_Jersey everything done in the US is old school.

[@r1ckastl3y86]

@Abdul Rahman yeah, but what if you have a plastic box holding a ceiling fan? I have that problem and I need to change it out with a ceiling fan rated box. the box holding my ceiling fan is a plastic switch box and it could fall at any time.

[@telosfd]

It is an advantage when the walls and ceilings are made of wood! Nice work. Question why there is no point on the ceiling from the beginning of construction for the installation of a luminaire?

[@macstrong1284]

The house, based on the style of the molding and height of the ceiling, was likely built before the common use of electricity in the home

[@Arieeeee]

Personally, if I was going through the trouble of running new switch legs, I'd install 4 LED recessed lights to have nice even lighting throughout the room instead of the glare that a single light source would have. At the very least, put in a flexible track so they can light up art work and make it look more modern. The single light in the middle is so 1970's. With the switch location, you don't put it in the middle of the wall. That's precious space for art work. You always put it on the side. Scott is a good electrician but has very poor taste in fixtures and lighting design.

[@bobloveswhiskey]

Ask This Old House needs more episodes with Scott

[@neil340]

6:12 good thing her ceiling joists run parallel to the wire

[@compactcow]

Probably could've continued up from the switch if that wasn't the case.

[@gregorall9779]

So who patched the hole in the upper wall?

[@justinwoods240]

From the cut away of the switch looks like points from an old engine like a Briggs or v8

[@heatherlollar4552]

This old house is interesting 😏

[@CaseyGpdx]

If I were you I would add a fan rated brace type box so it is future proofed and the ceiling won’t fall if a fan goes up

[@Vanilla_Icecream1231]

Same

[@chrisgast]

So, a driver is the power adapter between the 14 gauge and 18 gauge?

[@RobertMcSorleyJr]

So what do you do if you don't have a basement or an attic?

[@springer-qb4dv]

you'll have to fish wire from existing socket to the new switch box to hole on top of the wall and from there to the light cutout. However, if there are some studs and joists running perpendicular to path the fish tape, you'll have to make a cut out of drywall at each of those locations to drill and pull wire through. In other words, this video makes it look like cake walk, where as in real life it's nothing but.

[@LoneStarLynch]

The oscillating saw sounded like WALL-E

[@strangerofthe2067]

As a residential electrician with ten plus years of experience, as well as a professional troll on the internet, I can tell you that it is ALWAYS this easy and no skill is required. You could literally wire your whole house after watching this video. Just remember to have fun doing it. Your kids will be pulling wire in no time! Good luck! 👍

[@johnholfelder6724]

StrangerOf The206 Amazing how easy fishing wires is in old houses.

[@springer-qb4dv]

you forgot /S

[@jimcollins3411]

@@johnholfelder6724 Yes if nobody has blown the walls and attic full of insulation then it becomes a much harder job to do .

[@CitadelRunner]

Sure hope there is no stud under there as you cut...

[@steeezyb]

So when it burns out you get to replace the whole thing! Totally worth it

[@scottkurtz5167]

They're rated for like 20000 hours. Which is 10 years if you use it 8 hours a day. Seems pretty reasonable.

[@steeezyb]

@@scottkurtz5167 whats reasonable is the 70 year old porcelain ceiling fixture that hangs in your basement that can still be modernized with a replaceable led bulb! After factoring cost led starts making less and less sense when you start using expensive expendable fixtures like these.

[@TisiphoneLuv]

This true and since they are made In China 🇨🇳 Good Luck if it lasts more than 2 yrs! 🤨

[@r1ckastl3y86]

@@TisiphoneLuv I have had led bulbs last me only 3 months before so you would be lucky if it lasts a year or a year and a half.

[@wanaraz]

I think he still could have used the lamp. LED fixture just does not belong. But great how to video for THAT HOUSE.

[@mattzadworny]

lucky you didn't have any beams on a ceiling

[@brettvukovich6220]

That is one butt-ugly lighting fixture.

[@Slyvr18]

This videos always skip the hardest part of a job like this. How to figure out where to fish the wires without tearing apart all the drywall

[@jimcollins3411]

Yes and some old houses have insulation blown in them which makes fishing the wires a lot harder . After doing house building and remodel for 35 years i found a lot of old houses you can't fish wire though . Lot's of old multi floor houses had fire blocking put in horizontal and you have to drill a hole in it to get a wire though , meaning you cut a hole in the wall board large enough to get a drill in it to punch a hole in the fire blocking for the wire to pass though .

[@AngelaYah]

Please remember your dust masks!

[@khangnguyen-vg4tz]

after i'm done the light and i'm light you up too

[@stevecraft00]

33 seconds in. Points out a flaw with every american eldctrical outlet. Not a flaw with this installation specifically.

[@stephenbuckley6080]

Electrical isn’t a hobby hire an electrician.

[@chicanopridealvarez1385]

How about a ceiling fan install in same situation

[@bigman3944]

It’s ALWAYS this easy try it out, if you come back with spikey hair and a red mark on your hand DONT WORRY! Just means it works 👍🏻🙂