How We Built the Ultimate Cammed / Supercharged NBS Silverado Street Truck

[@RipRider916]

That truck is perfect for everyone. Not overdone not under. No stupid high gloss paint with horses airbrushed into the tailgate. Just a manly truck. Good job.

[@AZProPerformance]

Thank you!

[@mikeh1348]

Where can I look at info for my 2002 Silverado

[@cakeboy004]

This guys is talking about 20 years ago with those airbrushed horses 😂

[@hondaservicecenter]

Bro jst wanted to be racist

[@dogsandwich-b2r]

@@hondaservicecenter nothing to do with race lmao

[@Chase.bachler]

Easiest way to get the bolt out instead of dropping the gas tank is to cut the bolt and then install a new one facing outwards. Saved me a lot of time

[@_projectbuild]

Weight reduction😎

[@oceanwaves83]

Which bolt?

[@Chase.bachler]

@@oceanwaves83 the leaf spring bolt

[@oceanwaves83]

@@Chase.bachler ahh true. Thanks

[@1320sbc]

I did almost the same setup in my 05 a few years ago but 4.8L with a 2300 magnuson made just over 500 to the tire was my favorite daily wish I kept it that way

[@AZProPerformance]

I am hoping to get closer to 500 when we get up to 9.5 pounds of boost.

[@1320sbc]

@@AZProPerformance I have a new RDS spacer for that blower when you turn the boost up it helps a lot. I was going to set it up for meth injection under the supercharger lid so it doesn’t hurt the rotors but I never did before I sold the setup and went turbo. If you want it shoot me a DM you can have it

[@AZProPerformance]

@@1320sbc Awesome man and really appreciate that! Message sent.

[@JonTheDestroyer]

I wish you did too

[@seanspade951]

Y’all seem super knowledgeable I just bought a 4.3 I plan on doing a swap to the vortec 5.3 how well do these motors hold a charger? Y’all get any longevity out of yours or were y’all just racing it?

[@tunezZz01]

Takuaches in the comment section: “take notes cuh” 😂

[@DRGRACING]

🤣🤣

[@chuy2093]

He needs them traction bars so he don’t wheel hop

[@lambobroaventador6711]

Exactly what I’m doing cuz I got an NBS 2004 with the 4.8 😂

[@jerlaine1638]

Love those rims and shes perfectly lowered!! I've been debating on redoing the lowering kit on my truck and this just sold me

[@Jim-xj9se]

So glad to see the NBSs getting some love. I've been wondering what to do to wake up the 4.8 in my RCSB 01 Sliverado!

[@spencerharnedharned7211]

@@jason3211 R.C.S.B.- Regular Cab Short Bed/Box

[@Chase.bachler]

Find a 6.0 and swap it in. Ask me how I know lol

[@demarcusbody9437]

Boost it the 4.8 has some of the best rods for boost you’ll love it man

[@kel_bandz8462]

Cam it, bigger injectors, throttle body spacer, long tube headers, some new heads, let that thing breathe

[@demarcusbody9437]

@@kel_bandz8462 a men brother

[@SauceProphet]

Sweet Truck Build guys! I just bought a 03 sierra on saturday and cant wait to get some parts from you guys. Im in cali so the go fast will be a bit tough but everything else will be great!

[@_projectbuild]

Just bought a Silverado recently too. Good luck with your build! I hear it’s getting rough in Cali

[@RETSZTIRF]

He's right that really is the truck sweet spot.

[@ThatGuy17371]

What a great truck. i had a crew cab version a few years back and this was the end goal before i went stupid and bought a jeep. i still miss that truck.

[@anthonyharris7817]

I need a great mechanic like you guys.

[@2finger-Carmine]

It doesnt have everything you need... It has everything you want 💪🏻

[@trentdawg2832]

Ok bill carlton

[@goskidmark]

I would have added a new set of roller rockers and matching springs to eliminate the excessive wear to the valve guides (and entire valve train) that high-lift cams cause on the Gen 3/4 motors.

[@_projectbuild]

Good tip! Gonna try to remember this for my build as well.

[@Nolepower]

Man I'm jealous lolll. Wish I had the money to drop in my 1999 shortbed silverado. One day though. Thanks for the inspiration bro.

[@JonTostanoski]

They make it seem so easy. Or maybe it was because I did mine in my drive way and turbo it.

[@Silverado5.3]

Very cool. Can't wait to get some things done on my C10 Squarebody

[@garrettwoodard7834]

I’ve been drivin a 2003 GMC Sierra 1500 single cab for 7 years

[@harleyray2152]

THE MOTION OF AMERICA in “The Heartbeat Of America” font!!

[@SSANCHEZZ_505]

I want to say the rotors are directional and I thought I seen one on the wrong side. I'm not certain tho. Sweet build I want to get a street truck project started

[@AZProPerformance]

Thanks! Rotors are directional and do have them on correctly. Most guys think the pattern goes the other way, but indeed it is correct here.

[@joer5057]

At 11:18, buddy definitely had the driver's side rotor on the passenger rear, lol. You can see the "L" on it, and after the cut-away shot, you can see the pattern is reversed. Good catch though, I've seen guys run them backwards and not even realize it

[@SSANCHEZZ_505]

@Joe R thanks man I didn't even notice it switched after it cut away haha

[@HaroldjUSMC]

Truck is fire 🔥. I’m doing my step dad old GMC Sierra 1500. Right now just put Flow masters on this week

[@OfficialTWINKY]

Badass little truck I want one now 😂

[@elihamou6902]

2wd is great for a daily. Handles well, good mpg, and hauls ass!

[@whoisthis4130]

This is perfect and almost exactly what I want to do with my RCSB.

[@SkarryTerry]

Could have left it the way it was and it's still PERFECTION. Every man would agree.

[@rolandgutierrez813]

wow , that is amazing and so awesome that you did NOT have to butcher and cut the frame to get a Lower stance , very nice ,and you have all the strength of the frame too , can you post the model of that drop kit you did on the rear please , thanks man , love the look , great job ! i want 1 of those super chargers uggg

[@Pragmatist1st]

Coilovers are my now my next project on my NBS..... Also, get you an HD hood (will need a little work around the headlights, but easy and worth it).

[@MemphisTruckMafia]

I’m definitely putting coil overs on my single cab turbo nbs build now once I get it running which is soon

[@eleazar7962]

Awesome NBS daily 💪🏼

[@MemphisTruckMafia]

That’s nice I see some future mods for my turbo daily single cab build!

[@Sandhills_Coyote]

I love it! I just picked up a 04 yesterday will be doing something similar but probably a turbski. Cool little pickup!

[@AZProPerformance]

Thanks!

[@tareese78]

Awesome wish you guys could work on my obs love the work you guys do

[@bigjimsgarage31]

Do you guys remember what texas speed camshaft and valvesprings were put in the truck?

[@mrogersgmt800]

Love the set up! love the truck overall awesome work and video. 👌👍👍 I own 2 of these short beds 04 sierra and 00 Silverado both with the 4.8s beautiful rigs. Always fun to wrench on!

[@bnjmnnbl]

Truck came out pretty clean Travis! Might go this route myself one of these days!

[@billyp4674]

Love this truck ... Make an update video on this plz !!

[@AZProPerformance]

Thanks! A good customer actually ended up buying the truck and is enjoying it!

[@red01rado19]

Could you do a complete parts list on this?

[@chasecoster8791]

First time I’ve seen someone on KZbin put coils in correctly. Everyone just tried to compress it to put it in

[@_projectbuild]

When you start to compress things when working on your car tensions get real high😬

[@viivcreations9161]

cheaper and better than 2021 models :)

[@johnjohnson3783]

Perfect stance, I'm gonna have to copy tire size and drop. I need tires, and have the same truck, other than a 408 stroker, I've thought about a blower, but already a handful. Big thanks, it's just the way I want mine to look

[@mikeodell5915]

Great video

[@AZProPerformance]

Thank you!

[@chrissmith724]

Great stance! What about wheel backspacing? How much offset ?

[@AZProPerformance]

They are off the shelf DUB wheels and believe its a +30. Its a 20x9.5 wheel.

[@wilmillah]

@@AZProPerformance are these 20x9 or 9.5? i can only find them in a 9.5 wide for 22”

[@AZProPerformance]

@@wilmillah They are 20x9's. Give us a call, we are a dealer and can get them. 480-420-8175.

[@93rodeo58]

Immediately a new truck once it was lowered 🔥

[@AllAmericanAutomotive]

Beautifully done! I recently LQ9 swapped my 05 with 222k and have already been getting bad ideas floating around my head of...um...let's call it an intake manifold Vacuum elimination kit 🤣

[@Hoosier81]

Would’ve liked to seen how you ran the exhaust

[@chesspiece81]

Why not look into the 2019+ Silverado 4 piston calipers, or the C6 ZR1 calipers on the front and C7 Corvette calipers on the back? I've got a Brembo BBK on my Yukon and am going to do the C7 rear calipers. I got the Brembo kit before I knew about the C6 ZR1/2019+ Silverado calipers.

[@Kevin-us9yv]

Exacly my truck same year same cab same everything I love this truck

[@Kevin-us9yv]

update I sold it 2 weeks ago

[@ericringler608]

Killin it!

[@gs8602]

Great Look!

[@cashwrldtyy]

Gotta 01 same truck instead it's a step side i wanna build mine just like this 🔥

[@TheRcdude34]

Did you guys rebuild the internal of the motor at all, I noticed the odometer had like 250k. Solid truck tho I love it

[@AZProPerformance]

It was a 1-owner truck, so very clean. However, it already had a Jasper rebuilt 4.8 in it, with 10k on the odometer.

[@Dallas28-]

Pure performance 👏 🙌 👌

[@herculesworld4016]

Wheels look awesome. Great Job on the build. I have an 02 Tahoe and I fell in love with the way those wheels look. Are those wheels Dubs S205 LUXE? Thanks 💯

[@masont7408]

I always go to Cordes good guys!

[@robertbailey3057]

I originally felt like those HP guesses were low. I mean cam, exhaust, Cold air intake, etc should net a 4.8 north of 300 whp. I would expect more after a blower. But, I guess they didn't increase injector size or pump size and also depends on what fuel they are running.

[@AZProPerformance]

Yes, but remember, we are only at 5.5 pounds of boost which is light. It will go to a smaller pulley next week, to get 9.5 pounds of boost. Injectors are bigger and have more to give when we up the boost, without changing them. Just pump gas here.

[@jeepguy1337]

That black Silverado ss in the back

[@06jj28]

I was thinking the same shit.

[@ShooterMcgavin6]

How do those leafs effect towing

[@slopolopez7741]

Great video!!! So it was five g's for the truck... And how much for labor and parts? Asking for a friend.

[@viivcreations9161]

its Jayz2Cents brother!

[@User-pj9up]

Love this build, couldn’t have done it any better!

[@Yeeeeeeeettt]

I didn’t see any mention of a c-notch, did it ever bottom out? Looking to do the same but was wondering if I should order the c-notch at the same time.

[@MikeSmith-mp7lf]

Kinda late with my reply, but I have the exact same 1.9L magnuson supercharger with a BTR stage 3 truck cam, and TCI 2800 stall converter and I made 573 at the rear wheels. I recommend you check the duty on your injectors and the fuel pressure at your blower. You dont seem to be getting the power out of that blower that you should. Granted I have a 5.3 in my Silverado, but that's to much of a gap in power. You're basically getting crank horsepower at the wheels and that means only a 8-15% power increase from the blower. Also, PULLEY UPGRADES!!! Seriously. But if you're pleased with your results, by all means ride out. I'm not bashing your truck or build by any means, I just think you can get much more power than you are getting from this build. One last thing, what heads are you running on the 4.8? If I remember correctly, there was 2 or 3 castings that were horribly restrictive and that is the best way of unleashing extra ponies with forced induction. Oh! And 1 7/8 long tubes! Forgot about that one. Have fun. Nice build and like I said before, just some suggestions to maybe help you get a little more power.

[@AZProPerformance]

Appreciate it! In the video we do make mention up downsizing the pulley, which we did later and got more power. This was only about 5.5 pounds in it, which is light. We down-sized the pulley, more boost and re-tuned before the new owner got it. It has been doing well now.

[@joshuashelton7313]

how do you get it to sound that good it sounds amazing

[@AZProPerformance]

Thanks man! I agree, and one of the best sounding trucks I have owned. It is a Texas Speed cam and Speed Engineering long use headers with their exhaust / mufflers.

[@joshuashelton7313]

@@AZProPerformance i heard one last week it was a 2010 chevy silverado i want my truck to sound like that

[@jasonnellis3566]

Truck looks awesome. How wide was the rim you used.

[@birds000]

tryna do sumn like this in the summer

[@DaBuGzLiFe]

Needs something for that damn wheel hop.

[@AZProPerformance]

Yep! Our next KZbin shows the install of traction bars from Speed Engineering.

[@DaBuGzLiFe]

@@AZProPerformance Yes!

[@davidsharp922]

Most of the race trucks we build are 6.7 litre or larger stroker motors. There is no replacement for displacement.

[@AZProPerformance]

True, we are always fans of larger displacement, but we wanted to see what can be done with a 4.8 engine. Keeps the budget a little better! Thanks for watching.

[@davidsharp922]

@@AZProPerformance the 421 Ls we are fixing to put in a chevy truck will produce right around 700 horsepower. No turbo to get that power. It will have a nitrous system good for 200 to 300 hp more. It will smoke a 4.8 with a turbo no problem. Of course these aren't budget builds nor anywhere near the most expensive but really powerful tough motors.

[@AZProPerformance]

@@davidsharp922 I like what you got going on!

[@davidsharp922]

@@AZProPerformance my buddy at the shop likes to build trucks. Big motors,4l80e transmissions and 14 bolt rear ends. The one that is getting the 421 is going to be full race mode. He had a Fairmont with a 408 and 400 shot of nitrous that ran the 8th in 5.2 seconds at nearly 140 mph. Trucks are heavy but that's what he wants to build.

[@Blando7887]

I have an 02 NBS, the 4.3L just took a sht, educating myself on options. I be damned putting another 4.slow liter in it

[@Billythekid42069]

Lol mine is probably about to die on me it misses so much it sounds like rolling 2 step . But I have a gmc with a 5.3 as a donor for my Chevy

[@josueguillen5053]

I have a 4.3 in mine as well but its running 👍🏽

[@Kritzeon-_-]

i was wondering can u do a 87 chevy short wide. i really want to see that build

[@codydonovan7356]

Imagine if you put a equal length Vette style exhaust on it!

[@HardWorkpaysofff]

I have a 4.8 rwd ext cab that I’m trying to convert into a ss clone 6.0-6.2 haven’t decided ? What should I expect in a complete build ? Could it be done for 10k??

[@rippenxwhiskey4358]

I have a clean 2001 silverado, i dont want a turbo on it, but i do want a super charger preferebly a twin screw, which one would work with my 5.3?

[@pedrot9067]

What does it take to install a 4l80 in place of a 4l60 do you have to program the ecm?

[@767dag]

Awesome build , love it !!! Total cost in parts , ? …13k

[@codydonovan7356]

Those wheels look perfect. Where did you get them?

[@AZProPerformance]

Thanks! We sell them.

[@ThorntonFitness]

How much would something like this run to have done? I’ve got an 01 5.3L & would like to get something similar.

[@chandlerlofton6536]

What fuel pump did you use? What size injectors? Did you have to go returnless with the fuel rail on that blower set up? I’m building a 2000 Silverado very similar to what you did. I’m thinking about using the whipplecharger though. Awesome build man!

[@AZProPerformance]

Thanks man! It is a Aeromotive 450 we adapted to the stock basket. The Magnuson comes with injectors and a regulator that makes it a returnless basically. You'll like it a lot.

[@robertnewsome951]

I actually think it's a good number 390 to the wheels is no slouch. I have a 03 silverado rcsb 4.8 I want to cam and supercharge if I can get 39 off 5.5 lbs I'll be happy great video

[@robertnewsome951]

*390

[@garybensel6680]

I was under the impression you had to pull the heads to replace lifters on this engine?

[@ivanjimenez8868]

How do the lowering leaf springs handle corners and dips?

[@dakosyoutube6232]

How many days did it take for you to get this truck built? And how much was in?

[@krazylilalejjjjjjjandro4li527]

I NEED THE REAR END DIFFERENTIAL DONE TO MY 2011 AVALANCHE

[@not2old4watts]

I’m looking to do something very similar on a ‘01 Silverado with a 5.3. What’s the turnkey cost for this total upgrade?

[@lukedimitris11]

Love this built, did one like this but more motor 😂

[@jasonnellis3566]

hello when you removed the overload spring how did it ride

[@Its_Bobbys_World]

I like it man but dang I would have been disappointed with that power level I did 450hp/435ish trq with a cam only 6.2 swap on my silverado it’s on my channel

[@yehornaumov5893]

Chevy you fix it with a hammer 🔨😏

[@Bob-Sacamano]

There's nothing funnier than reading the comments of all the armchair LS experts here. 397whp on that setup thru a 4L80e is impressive. On 5.5lbs and mild blower cam I woulda guessed ~360whp

[@kylerickels6464]

I would have guessed a lot more honestly, my cammed 5.3 makes 344whp in a 2004 regular cab long bed

[@Bob-Sacamano]

@@kylerickels6464 What cam?

[@kylerickels6464]

@@Bob-Sacamano 227/235 custom grind

[@Bob-Sacamano]

@@kylerickels6464 So you got a relatively big cam for a 5.3 in a truck. Point is, you have a 10% more cubes, likely bigger cam than theirs and lose less power through a 4L60e vs their 4L80e. 397whp on a parasitic supercharger with just 5.5psi is a great number. Any HP calculator would say the same and it still has a lot more to go with just a pulley change. I think people are getting a little too optimistic on hp numbers these days watching sloppy style builds with big 78+mm turbos on lots of boost.

[@seanspade951]

@@Bob-Sacamano not at all man , everyone’s build is different my homie has one with custom z06 cams and a blower (not sure which one) but he dynod at like 480 to the wheel man… use the right parts for the right numbers, his definitely takes a little more of a beating then there’s would but those numbers are relatively easy

[@Valdemar-Perez-III]

Y'all should be qualified to be part of powernation.

[@SamSheepDoq]

What throttle cable bracket did you use? I need one for mine

[@blacklight4460]

Since you you're already giving up practicality with the reg cab and you have the stout 4.8l, why not increase your boost pressure to make it more crazy and less practical?

[@Conker999]

Nice i have an 03 cateye with an LS3 at 480whp

[@xXNolanRyan34Xx]

Can you do the same lowering kit on a 4x4?

[@AZProPerformance]

Yep, sure can. Give us a call.

[@xXNolanRyan34Xx]

@@AZProPerformance looking for a truck at the moment but you’ll get a call once I find a truck to build !

[@fredbonez1803]

If you build the 4l60 to a stage 4 would it hold up ?

[@bryanball8909]

To bad y'all have to sub all that work out. The rear end is a bit of a pain, but all that other stuff y'all could handle. Oh I forgot about the dyno.

[@AZProPerformance]

We know we could have done it. We are very busy at the shop, so really didn't have time. Plus we like to use our friends in the industry as well. We all like to work together on projects, but have built plenty of trucks in house and do know our way around them.

[@lathangarner222]

Love the truck have me some ideas for mine and most these people done realize how reliable that set up is also your a pulley swap away from 450-500 easy lol everyone thinks their a genius turbocharged applications are cool but definitely not my choice for a “daily” lol “ o shit bro I think my random line is leaking “

[@lukedimitris11]

Do you guys make a whole kit for the 2/4 drop that’s on this truck?

[@AZProPerformance]

We sure do! Ours was double adjustables, but offer in a single adjustable too. azproperformance.com/collections/99-06-silverado-coilover-complete-kits/products/pro-performance-2-4-drop-w-coilovers-99-06-gm-truck-suv

[@erickuribe9860]

This thing is supa sweet😎

[@juanvela2229]

Any tire rubbing with that combo. Love the stance 😍

[@AZProPerformance]

Thanks! No rubbing at all and fit very well.

[@juanvela2229]

@@AZProPerformance cool, thanks. Just subscribed 👊

[@jeremyellis7364]

What’s the driveshaft situation with the 4L 80 swap? I am assuming the 4L 60 driveshaft can’t be used.

[@AZProPerformance]

Correct, we had it shortened.

[@schmokeone]

Do you have a link to the lowering leaf springs?

[@AZProPerformance]

We don't as we dont recommend the drop leafs. They ride very stiff. We later switched to a drop shackle and hanger, and although more work, it is worth it. azproperformance.com/collections/99-06-silverado-coilover-complete-kits/products/pro-performance-2-4-drop-w-coilovers-99-06-gm-truck-suv

[@jesseramirez3131]

Hi guys love ur videos and I was wondering how much did everything cost and how much u think it well cost if I go to sum place so they can put it on I'm 16 right now and I have 3k right now

[@AZProPerformance]

We can do all the work, but never really added up all the parts however. The supercharger but itself (just parts) is about $6,500.

[@jesseramirez3131]

@@AZProPerformance dam do yall got a shop in San Antonio tx

[@ed-ou812]

I have a restored 1997 4x4 suburban with a 5.7 vortec crate. I wish to install a cam and supercharger. What transmission and rear end changes would you recommend?

[@AZProPerformance]

I would do a 4L80E and a good Posi unit in the stock rear end. You can build the 4L60 to handle the power increase, but our opinion is to just skip that, and go right to the stronger 4L80.