This is the first helpful video I have found....representing East Rand, Gauteng
@kikonsdofficial59964 жыл бұрын
I have a question I'm the operator of iuv compress machine. My problem i don't no how to removed the head from the guard and also the problem i don't no how to removed the dry ink from the head how to possible to removed the dry ink from the head...
@aunderforge77926 жыл бұрын
o is it okay to flush that strong its so scary it might damage the head i had a really big problem to my head so much clogging but i cant clean it well coz too afraid to that like yours
@myidealwaist41515 жыл бұрын
Why you didn’t clean it in the sink instead of dirtying the beautiful brick??
@dariosalvati52513 жыл бұрын
ma funziona ancora la testa?hai sfondato tutte le linnee con quella pressione
@mquynhanh104 жыл бұрын
How often we should clean a printhead?
@ericjohnson45713 жыл бұрын
If you want buy a new print head do this technique it almost always destroys the piezo crystals inside a Epson head. But if its messed up what do you have to loose. Be extremely careful about fluid getting into the electrical components, cause if you plug it in with fluid you will probably be buying a main board, ribbon cables, print head and a head board. There are other techniques that are not nearly as invasive nor have the chance of killing a printer. Oh and once you pull a head you get the pleasure of doing XYZ alignments for the next hour. Just saying
@meridianxv883 жыл бұрын
Hi Eric, what would be the best way to clean a head that is slightly clogged? My yellow head got clogged once and I had them come service it, they said it wasn't a big issue and they cleaned it pretty quickly without removing the head. However 1 month later it seems to have started the same issue again.
@djukee5 жыл бұрын
I did this metod fjy times only on magenta chanel, and no way to get that waterflow effect, only droplets are comming out. I try also leaving in solvent for fly hours but didnt fix the isue There is no spraying. Any one know what can i do to fix it? Thanks in andvance
@websigns61036 жыл бұрын
Hi, The same problem is here as well.I am too scared too put that much pressure on the Print Head as it might damage it. Please can any one advise.
@KingHumphrey-PrinterHealer4 жыл бұрын
Get an engineer for that. Thank you!
@ГосподинМаксим-ь2щ5 жыл бұрын
what is called flushing ?
@hmyvid30644 жыл бұрын
For this method you need a syringe, a small tube (that fits over the syringe tip) and the liquid solution. As shown in the video you then fill the syringe with the help of the tube to reach the liquid. When you have done that you can attach the other end to a hole on the printhead and then inject the liquid. You will see the liquid solution should come out on the other side, possibly in the colour that you are trying to unclog. Continue injecting the solution for all the other holes until only clear liquid comes out.
@Mz-gz2is5 жыл бұрын
the plate is it golden????
@racheleasterling9676 жыл бұрын
Is there a video on how to remove the printhead from the printer?
@alexventuree81005 жыл бұрын
The cost of the video is 89 dlls
@manojdaryani40123 жыл бұрын
@@alexventuree8100 I will buy
@timdoreck32084 жыл бұрын
What is the inside diameter of the tubing for the best fit on the printhead nipples?
@AchievementMatters4 жыл бұрын
Depends on your printhead. Normally a 4mm tube (inner about 3mm)
@ollarq1596 жыл бұрын
i did it like you, but now when i pull water through the print head, the water goes out by 2 colours.. is it damaged now? :(
@AchievementMatters6 жыл бұрын
Hard to say, because this technique is last method and should not use if clean by machine still works. Anyway, you should not push too hard. And if damaged after wash, it might be damaged before already, only the wash expose it. Because when inside interconnected, most likely is cause by the internal heat melt the components. And blockage will cause internal heat up.
@okubassey22364 жыл бұрын
Please my print head is printing to one side even when the material is straight. Please help..
@edoborfrederick42854 жыл бұрын
Plssssss what is the fluid called?
@AchievementMatters4 жыл бұрын
Cleaning liquid buythis.co.za/f-eco-clean
@robertmontero7073 жыл бұрын
It is called eco solvent fluid. Can order on Ebay
@Alexios586 жыл бұрын
I did this and now my print head cant print
@CCproV4 жыл бұрын
Thank goodness I read this comment before I tried it 🤣
@bazilo134you4 жыл бұрын
@@CCproV hahahaha that method will certaninly damage the print head, the best way if you want to pass the solution inside the printhead is to push very very gently and then pull more gently to extract the dried ink that clogged the printhead but also have in mind that if your printhead have too much time in use may very well be a time to replace it.
@Alexios586 жыл бұрын
There is no color now in my print head
@omarperalta53786 жыл бұрын
If you put to much pressure you will damage the head. Put the head on solution and let it rest for a couple hours and then pull with the syringe, dont push just pull.
@alexventuree81006 жыл бұрын
Omar Peralta what kind printer you have?
@omarperalta53786 жыл бұрын
I sell printers. And work for big production companies. The printers that i have used are Mutoh, Mimaki, Epson F series, Rollan and Chinese printers. The printheads DX7, DX5, DX6 and Epson 5113 print head.
@alexventuree81006 жыл бұрын
I have the epson stylus pro 9900 but i want to make the clean in the green channel partially clog. What you thing about the clean process?
@omarperalta53786 жыл бұрын
If you can, take the head out and with a small syringe push a little portion of cleaning solution on that channel and let it rest for a couple minutes and then push distilled water and install the head again and do a auto cleaning.