Hi, Thanks to your video, my printer is fixed !! I just removed the foam and the problem is gone . Cheers !!
@jjjShema5 жыл бұрын
Omg! thnx bro, finally this video saves my spinning day, I hardly understood the language but still, I followed the steps and fixed the ERROR 59.F0 on a CP4525, obligado parabens !!!!
@mihailelea5 жыл бұрын
Thak you! I had error 59.00.F0 on a CM4540FKSM and I had no idea what could cause it. After I saw your video I found that solenoid on my printer, cleaned it, and the error is gone, so this fix works on CM4540 as well. Of course it took me the whole day to do it :))). Thank's again!
@scrwdrvr5 жыл бұрын
Is the disassembly and reassembly procedure similar or same?
@mihailelea5 жыл бұрын
Not quite the same, but after you remove the scanner and the top side, the procedure is very similar. Most of the parts are in the same place, but you have a few extra things because you have the scanner.
@scrwdrvr5 жыл бұрын
Thank you for your feedback. I have modified the description.
@damonsisk42704 жыл бұрын
Machines less complex than this printer took man to the moon...
@Dave527326 жыл бұрын
Thanks for the disassembly of this area, I get to replace the fuser drive in one today :-(
@ShyRockFreak862 жыл бұрын
Unless, of course, from the .001% chance it is actually the Fuser main drive assembly.. oi.. good video
@gglovato4 жыл бұрын
This is an absolute nightmare, how am I supposed to do half the steps on the mfp version??. Can this be done without removing the psus or so many components?
@aabsc3 жыл бұрын
Did you end up doing it? I have to do it on the MFP version too.
@gglovato3 жыл бұрын
@@aabsc no, never got the time and space to do it, it's on the eternal "to do"
@ArmorKing0120005 жыл бұрын
thank you very much for information. Hi from Lima Perú.
@BehzadEghtesad Жыл бұрын
Thanks for this movie. i have a CM3530 printing fine on USB but cannot connect it via LAN, win10 dose not recognize the LAN. The cable is fine, ip4 is fine. possible the formatter board needs to replace?
@scrwdrvr Жыл бұрын
Yes, it is possible, but usually defective formatter boards cause other problems not that one. 1. Connect the printer to an unmanaged switch or router. If the port led goes on than the link is OK. 2. Try to check the layer 2 communication. I use Lantronix Device Installer. You'll see if it is OK. (Your computer's connection needs to be OK.) 3. If the first two steps are OK than you have a layer 3 problem with IP settings. You can try a factory reset on the printer, but sometimes it can cause other problems.
@ВолодимирПетрович-р5ч4 жыл бұрын
Спасибо за видео,вы помогли мне
@mostafaali71866 жыл бұрын
بفضل الله بحل المشكلة دى ف ساعه بس
@chahinechahine30065 жыл бұрын
السلام عليك اخي ان لدي نفس المشكله ماهو الحل شكرا
@nekooking19944 жыл бұрын
good morning I have a question, I have an hp cp4525 with faults in the page counter, she counts them when I print them and after I turn off the printer and turn it on she subtracts the pages already printed from the counter, you know what is happening that? do you have any solution for that failure?
@aabsc3 жыл бұрын
Hi, I will need to do this on the CM3530 MFP (Printer/Scanner/Copier) version of this machine, how complicated is it to remove the scanner/control panel top, or is it necessary to remove it for this repair? Also why is the power supply removed? It does not seem to be in the way, Thank you
@scrwdrvr3 жыл бұрын
It is necessary to remove the scanner, but I don't know how complex it will be. In connection with the PS: I don't remember exactly because it was 4 years ago when I made the video, but I think it was necessary to remove it.
@ADRIENMOYOLO10 ай бұрын
Ce très intéressant ça me donne un plus 😮
@darthjar91174 жыл бұрын
This video proves you don’t have to remove the main drive or the lower high voltage board
@AlisonPetersongo6 жыл бұрын
Hi I have a m452dw printer that has the same error 59.f0 do you think applying the piece of tape on the solenoid would fix it?
@scrwdrvr6 жыл бұрын
No i think. M452dw is young yet. The "sponge error" come about min. 4-5 years.
@aircats6 жыл бұрын
Thank you for this video!
@alejandrobrousson42076 жыл бұрын
hi, i remove the brown sponge from the solenoid and glue there a thin plastic piece and the printer have a 52.00 error, do you know what error it is?
@scrwdrvr6 жыл бұрын
52.00: The scanner has experienced a startup error. Check the following connectors: J501, J503 on the laser PCA and J106, J110, J111 on the DC controller PCA
@hitmanbluesband2 жыл бұрын
I replaced the whole fuser drive assembly but now get a 55.01.00 DC Controller Memory error. I've replaced the DC Controller board - still get the error. I triple checked all the connections on the board AND behind the High Voltage Power Supply (upper) - nothing is disconnected. I replaced the DC Controller again, still the error. Any ideas on this?
@scrwdrvr2 жыл бұрын
I haven't got any specific hint. But: was the first 55.01.00 appearance after you changed the fuser drive? If yes, then you should search the reason where you "walked" during the replacement.
@hitmanbluesband2 жыл бұрын
@@scrwdrvr Thank you for the reply, but I'm not sure I understand what you mean by "the reason where you walked during the replacement". Right now, the printer is sitting disassembled up to 19:18 on the video . I didn't go further, because I just wanted to make sure nothing was left disconnected (it wasn't). And yes, that error made it's first appearance after replacing the fuser drive. So I replaced the DC Controller board (twice!) but it didn't make any difference, so I'm guessing it ISN'T the DC PCA. Thanks again, and please let me know what you meant.
@scrwdrvr2 жыл бұрын
@@hitmanbluesband I'm affraid that the error was caused be the repair process. A loose groud wire, two interchangeable cable, a poor contact can cause an inexplicable error. You right, the DC PCA is likely OK as before.
@nekooking19944 жыл бұрын
buenos dias tengo una duda, tengo una hp cp4525 con fallas en el contador de paginas, ella las cuenta al momento de que las imprimo y luego que apago la impresora y la enciendo ella me resta del contador las paginas ya impresas, sabes xq esta pasando eso? tienes alguna solucion para esa falla?
@aabsc3 жыл бұрын
Hi, I finally got to replacing the entire fuser drive assembly but when I took apart the old one the solenoid doesn't seem to stick, does this mean that wasn't the cause of my 59.F0 error or does the sticking not have to be noticeable to cause the error? If it sticks it's for a fraction of a second and barely noticeable, is that enough to cause an error? Thank you
@scrwdrvr3 жыл бұрын
Yes, because it works repeatedly and the time period while it sticks became longer and longer.
@aabsc3 жыл бұрын
@@scrwdrvr It fixed it! Thank you kzbin.info/www/bejne/hIiXhnSVaa2EhKs
@vicentemeza784 жыл бұрын
Thanks for your video, it really helped me with many printers i've had paralyzed because of this trouble. But i have a question: Can i left the solenoid without that tiny sponge? Thanks again.
@scrwdrvr4 жыл бұрын
No, you have to glue there a thin piece of plastic.
@ShyRockFreak862 жыл бұрын
On a solenoid. You can never have metal to metal contact, or magnetization will occur. Replace the foam pad with proofing material like felt, or slip 3:8” shrink wrap tubing over the foam pad lip. You’ll never have this problem again.
@h2b2666 жыл бұрын
Obrigado... Foi de grande Ajuda!!!
@jsitalo16 жыл бұрын
thank you for this video! obrigado parabens ! - brasil
@patpending_6 жыл бұрын
Hello ! I followed the instructions in your video about error 59.F0 (CP3525) , I removed the sponge. After assembling back the printer I get an error 59.30 on the display. Any tip ? Help !
@scrwdrvr6 жыл бұрын
Check J117 connector on DC controller. Check fuser motor rotation.
@patpending_6 жыл бұрын
Thank you !
@Officialmotive8054 жыл бұрын
Thank you
@ShyRockFreak862 жыл бұрын
There is NEVER a reason to have to take the LVPS out to repair this error, nor disassembly of the DC controller board.. 30 minutes in and out, from power down to start to power up to test..
@ShyRockFreak862 жыл бұрын
This is for a transfer belt solenoid in the comment above..
@heminghway7 жыл бұрын
Hi there! I have the same printer (HP Color LaserJet CP3525n) with the same error (59.F0 error). We first thought that the problem was the ITB, we already ordered and replaced the ITB with new one, but still have the same error, and I also hear a noise inside the printer. Do you think it is necessary to replace the white gears and the solenoid, or there is another way to fix this printer? Thank you in advance for your help. By the way, great job!
@scrwdrvr7 жыл бұрын
Hi! I think it's enough when you remove the brown sponge from the solenoid and glue there a thin plastic piece. Pay attention white gears position!
@heminghway7 жыл бұрын
Thank you VERY MUCH. I finally get the solenoid out of the printer, very difficult! Can you tell me what kind of plastic should I use to fix the problem? And what size? 1 millimeters or 2 millimeters? Maybe thicker? And what about to test the solenoid outside, how can I be sure that it is working fine? Thanks again!
@scrwdrvr7 жыл бұрын
Never mind, 1mm or 2mm is ok. If you cleaned the sticky area then it will work fine.
@musanganga1257 жыл бұрын
apparently mine still showing the same error after applying the plastic it wont boot past 59F0 error...
@musanganga1257 жыл бұрын
new fuser kit by the way...
@hajaratalisayyed87695 жыл бұрын
This is very helpful vedoo
@absalongc62886 жыл бұрын
Gracias
@kofiivory73416 жыл бұрын
hello, thanks. i did mine but afterwards i have an error: imcompatible fuser. kindly help.
@scrwdrvr6 жыл бұрын
Hello, Check the connectors between the fuser and the pcbs.
@kofiivory73416 жыл бұрын
thanks but now I've 52.0 and I can't locate J501, J503 at all. where can I find it on the machine pls?. any kind of help would be appreciated. thanks
@scrwdrvr6 жыл бұрын
First check J106, J110, J111 on the DC controller PCA.
@kofiivory73416 жыл бұрын
thanks! works fine now.
@ArmorKing0120005 жыл бұрын
Is it the same as HP LJ 500 color?
@scrwdrvr5 жыл бұрын
Very similar I think. Watch this video: kzbin.info/www/bejne/o2aVgoSIf6p7nLM
@youssefouabouch41785 жыл бұрын
bonjour tous le monde, c'est très util cette video, est ce qu'il y a quelq'un qui a un cite où puis-je acheter ce solenoide sur internetc'est urgent merci
@elmountassifmohamed19436 жыл бұрын
Good job
@axistube15306 жыл бұрын
Tank U
@ivankostsov2536 жыл бұрын
like, bro!
@universoul746 жыл бұрын
Part number for this unit?
@scrwdrvr6 жыл бұрын
Fusing (fixing) drive assembly with motor (duplex) RM1-4974-000CN Fusing (fixing) drive assembly with motor (simplex) RM1-5001-000CN
@nekooking19944 жыл бұрын
esa misma falla la este modelo también si tienes la solución a esa falla me ayudarías mucho elgato9_15@hotmail.com si encuentras una solución avísame
@ViktorVoda5 жыл бұрын
kár hogy szar a felbontás, lószart se látni :(
@scrwdrvr5 жыл бұрын
A szervizkönyv sokat segít a video mellé, érdemes letölteni.