HPI Baja Getting Started Guide

  Рет қаралды 336,111

HPI Racing

HPI Racing

Күн бұрын

Пікірлер: 153
@FreakoRico999
@FreakoRico999 2 жыл бұрын
Old video material, but still all these HPI video's are one of the best instructional video's ever.
@AlexRcHandyman
@AlexRcHandyman 4 ай бұрын
Ive still got one of these brand new in the box !
@stanworth88
@stanworth88 11 жыл бұрын
I have a 29cc Baja 5T and it's pretty fast with the right tuning, i have an 8000RPM clutch, 20 tooth pinion and 57 tooth spur with a tuned pipe and it drifts around fine, jumps fine, and it fast, i had to change the breaks because of the speed of them little things, i put hydraulic front brakes on to help it stop better, the amount of perfomance mods out there for these type of cars is unreal, i'll be getting a stuffed +2mm stroker crank bigger fuel lines, polished carb and ported head soon
@eduardoj.hudson1238
@eduardoj.hudson1238 Жыл бұрын
Good but you should have a 54t spur gear with that pinion, oterwise it won't fit or you make a mistake here at describe it
@cyberripper475
@cyberripper475 6 жыл бұрын
I wish they would return the old version of the baja with the purple parts and nice orange body cover
@Barthoization
@Barthoization 12 жыл бұрын
its a 2-stroke , so for the first time, warm it up gently by driving it, max half throttle. Let it cool down fully, repeat the previous again. After warming it up for the 3d time its ready to rip. Break-in = setting the piston-rings to the cylinder. Idling the engine for 6 tanks is just a waste of fuel and time. ( not to mention carbon-buildup on the piston by not reaching optimum heat)
@tolgahancakir1571
@tolgahancakir1571 6 ай бұрын
Hpi did a great job building a beast🎉
@stanworth88
@stanworth88 11 жыл бұрын
Check your front wheel alignment make sure both wheels point streight ahead, you can alter the tracking by turning the track rod ends, they are the metal bars by the A arms with the flat spots on them so you can turn them with a wrench, also you might want to check the toe in angle on the back wheels, if one toes in more than the other it can cause it to pull to one side, you can also try turning the rear hub spacers 180 degrees to make the rear wheels streight.
@SteveMagr
@SteveMagr 4 жыл бұрын
15:00 pull-start disassembly and clean. Excellent.
@eliejsukkar2211
@eliejsukkar2211 11 жыл бұрын
lol i remember 7 years ago when i got one of these, they were a lawn shredder to the grass in the park, just ordered the 5sc ss today, these are great ;)
@FishKeepingManiac
@FishKeepingManiac 11 жыл бұрын
yes usually 92 octane and 2 stroke oil, with a mixture of 20:1 or 25 :1
@addyrcshorts
@addyrcshorts Жыл бұрын
How to keep the idle needle in factory settings
@mike85sx
@mike85sx 14 жыл бұрын
so basically the rule is 1 battery per tank until u recharge it .....great vid cheers
@fatkhetburnell
@fatkhetburnell 8 жыл бұрын
This looks like an educational video filmed in the 70s. WTF HPI.
@fortruthnoterror7796
@fortruthnoterror7796 6 жыл бұрын
LifeInRecoil I was 6 when that video was released now nearly 20 (intro)
@bradleypendleton202
@bradleypendleton202 6 жыл бұрын
ForTruth NotError if u where 6 you would be like 15 now not 20
@biglakepigs
@biglakepigs 5 жыл бұрын
Lol
@bajamike3803
@bajamike3803 6 жыл бұрын
I miss the hpi purple
@AB-80X
@AB-80X 5 жыл бұрын
Orange was better.
@TheMickeyV
@TheMickeyV 13 жыл бұрын
@littleboblives the air filter is for the keep some durt out to make sore that there is noting going in to the engine onlye air
@eathynpatrick1601
@eathynpatrick1601 4 жыл бұрын
Need help?? Got a Baja 5 b it has a rattle in the engine when I pull the cord. And goes through spark plugs like nothing?
@AndysRC08
@AndysRC08 10 жыл бұрын
I wish I have one of those and I like the sound of a 23 cc 2 stroke engine and 32 cc and a 35 cc engine
@Hpj007
@Hpj007 12 жыл бұрын
the break in for the fulie engine that ive been told is run it easy for 1 tank then run it as you want is from some of the most well know modifiers for baja's that i know. idiling for 6 tanks is just a waste of fuel. also the 2 strokes for bicycles maybe a bit different too. like for nitro engines each manufacture has a different break in process for their engine. like hpi they have the ebst break in for their motor each company will be different from the last dealing with the break in proces
@littleboblives
@littleboblives 14 жыл бұрын
what does the air filter oil do? if you are going to take apart the pull start make sure you hold the parts in as the spring inside likes to shoot all the parts out and unwind itself making it really hard to put back together
@SteveMagr
@SteveMagr 4 жыл бұрын
18:50 carby settings - great!
@jeromejasper9111
@jeromejasper9111 3 жыл бұрын
Can I use a 7v battery in my exeed hannibal 5th scale gas truck ? For the receiver and servos? Ty
@MyForsake
@MyForsake 12 жыл бұрын
very informative. can't afford it anyway xD
@patricktrotter9125
@patricktrotter9125 Жыл бұрын
What make a fifth scale gas car wheel term when you crack it
@decimocentauro3764
@decimocentauro3764 5 жыл бұрын
So no specific break-in ? Like running idle for 15 mins, then let it cool down for 15 mins and repeat every time with 1/4 throttle more ?
@user-sv6qq8tp9x
@user-sv6qq8tp9x 9 жыл бұрын
95 is standard in UK I run my golf on 98 from shell
@AB-80X
@AB-80X 5 жыл бұрын
And why are you saying that?
@abdulnezha5429
@abdulnezha5429 6 жыл бұрын
Really a Great video mate! Thank You
@charlesmcgehee3227
@charlesmcgehee3227 5 жыл бұрын
Hi. I am looking for a replacement engine for my HPI RS4 EVO3 RTR. HPI PART # 15107 They are discontinued but doesn't someone have these engines? I would appreciate some direction. I bought it and it was supposed to be new. It came in a sealed box and was brand new stock. The engine blew. Not sure what happened. Needs a piton, sleeve and drive shaft. Too much money and parts not available. Anyone reading this with an idea for me let me know. I don't want to fit another engine in. Don't have the parts or the time.
@eternalrevolt7466
@eternalrevolt7466 6 жыл бұрын
After 10 mins of running... The engine stopped and now my pull start won't pull. I was running it in wet conditions. Did I maybe get dirt/mud inside... Idk
@BajamanCam
@BajamanCam 12 жыл бұрын
Std. or upgraded clutch, both will stopp slipping between the 10-12k mark. Aftermarket clutch such as lauterbacher clutch will only improve smooth acceleration, not top speed.
@hammerhome7879
@hammerhome7879 7 жыл бұрын
I cant believe HPI has stuck with that long wheel base for so long , I chopped 1" off my chassis and it no longer nose dives or loops out easily . Its not that the front end is too heavy , its that the weight is leveraged to far forward.. OHH and about 1" wider....Are you listening HPI?
@SnookTuned
@SnookTuned 6 жыл бұрын
The wheel base is distance between the wheels...
@natcoyle-palmer8753
@natcoyle-palmer8753 4 жыл бұрын
Hi mine is getting delivered in a min so do I change shock fluid or do I leave it for a few weeks
@1091jordan
@1091jordan 12 жыл бұрын
Yes actually i do know about 2-stroke engines. A stuffer crank can improve performance and strengh, but yes, it will not increese the top speed. If you run a stock clutch, it is more likely to slip inside the clutch bell, if you run a 4 shoe race clutch, then it is not likely to slip, therefore you will get better speed.
@bradleymilton9372
@bradleymilton9372 11 ай бұрын
Don't lie
@deonstrydom5176
@deonstrydom5176 5 жыл бұрын
Some one messed with my remote/pushed buttons now my remote does not read my car...please help?
@BarraGutheWorld
@BarraGutheWorld 5 жыл бұрын
Re bind the remote and receiver
@TheDeepImpact965
@TheDeepImpact965 13 жыл бұрын
No break in procedure with gasoline engines?
@willvanallsburg4703
@willvanallsburg4703 8 жыл бұрын
can you fit a obr 30.5cc engine in this car?
@johnboymcdan6786
@johnboymcdan6786 8 жыл бұрын
Seemingly Suprized yes you can bud
@willvanallsburg4703
@willvanallsburg4703 8 жыл бұрын
cool
@khaledmaher6602
@khaledmaher6602 3 жыл бұрын
you can fit 45cc engines too
@mohamedsherif5791
@mohamedsherif5791 3 жыл бұрын
what is the use of air filter oil? and what will happen if i didnt put air filter oil?
@genericgoogleaccount8907
@genericgoogleaccount8907 3 жыл бұрын
It stops dirt from getting into your engine. If you don't put it on then you'll get dirt in your engine and the dirt will scratch the engine's walls leading to lack of performance and eventually complete engine failure.
@SafwaniTube
@SafwaniTube 12 жыл бұрын
recently, I got 5b ss. but i can't make it go in straigh line . why is that ?
@javiergil8228
@javiergil8228 10 жыл бұрын
So never leve gas in the tank damm I do that I didn't know that does anyone know we're I can get a muffler a good one
@1091jordan
@1091jordan 12 жыл бұрын
i up-graded my stock 26cc engine to a 30.5cc. If you want more power and acceleration then this is a vital up-grade. Also, By any chace, if anyone has a Kingmotor Baja 5B, Then you should up-grade the engine and carby any way. I have a KM and my engine and carby were, well, Shit. slow acceleration and very little top end speed. Apperently if you try to tune a kingmotor carby, the carby wont hold that possition for long. So if you are happy with the engine, then upgrade the carby
@ellawoodmansey
@ellawoodmansey 10 ай бұрын
Whats the name of the charger as i seem to have misplaced mine :D
@OfficialHPI
@OfficialHPI 10 ай бұрын
I'd recommend this charger from our current range for the receiver pack: www.hpiracing.com/en/part/118051
@josezenteno4231
@josezenteno4231 2 жыл бұрын
Dónde se consiguen?
@MultiSniper70
@MultiSniper70 12 жыл бұрын
you can buy a 30.5cc engine and a tuned pipe i want a performance upgrade on a lozi 5t 4wd
@zamiercarmichael7405
@zamiercarmichael7405 8 жыл бұрын
does it have a ideal
@GGobblin
@GGobblin 10 жыл бұрын
Sunaco Ultra is like 94 octane. One if the highest grades. 89 is more like a standard octane
@FgFg-zh5lf
@FgFg-zh5lf 9 жыл бұрын
can same one guide me how many turn i need to do for the carburetor adjusting ?( its very fast in the video ) thanks
@bombakdik
@bombakdik 11 жыл бұрын
Seems like the engine isn't too good in the low revs?
@watuhenk7398
@watuhenk7398 9 жыл бұрын
where can I buy baja 5b ss?
@willvanallsburg4703
@willvanallsburg4703 8 жыл бұрын
Jesus Christ man you want me to use race fuel???????!!!!!!!!! there is no regular 95 octane all we have is 92 and 115
@abdulnezha5429
@abdulnezha5429 6 жыл бұрын
😆
@Winter1256
@Winter1256 4 жыл бұрын
In Europe we do have 95 and 98 only
@SUPERFORMIAN
@SUPERFORMIAN 12 жыл бұрын
However, idling it for 6 tanks of fuel wouldn't hurt. However, I find it strange. The 2-stroke engines for bicycles require a break-in process. The Fuelie engines and others alike aren't much different. Why does the Fuelie get excused from the break-in process?
@1091jordan
@1091jordan 12 жыл бұрын
The fist day i got my Baja 5B, i reved the shit out of it. Didn't bother with the break-in process. I personally don't believe in it. It performs excelent, up to 110km/h and uses a tank of fuel in about 40 minutes. but i have a 30.5cc engine. Not the stock 23cc or 26cc depending on which kit you bought.
@TheMickeyV
@TheMickeyV 14 жыл бұрын
@leeadamaa dude standard 95 and 98. is 89 en 92 in the eu
@GriffXJ
@GriffXJ 12 жыл бұрын
What about 87 octane? That's standard in my area (87, 89, 93)
@johnboymcdan6786
@johnboymcdan6786 8 жыл бұрын
Can it make a cup of tea?
@kreizmann2943
@kreizmann2943 8 жыл бұрын
and some biscets?
@kreizmann2943
@kreizmann2943 8 жыл бұрын
typical british xD
@johnboymcdan6786
@johnboymcdan6786 8 жыл бұрын
Nice BAjA :0)
@Jaketunnell
@Jaketunnell 6 жыл бұрын
Krispy I'm British
@hallobyebye699
@hallobyebye699 5 жыл бұрын
Can it go to the shop for some krisps
@KL33CHRY
@KL33CHRY 5 жыл бұрын
Does it have a reverse gear ?
@TJ-ux6ng
@TJ-ux6ng 5 жыл бұрын
Joseph Geoji no only forward and brake
@sreelalroy_v
@sreelalroy_v 7 жыл бұрын
Where do I get hpi Baja RC in India... Please reply
@hallobyebye699
@hallobyebye699 6 жыл бұрын
sreelal roy aliexpress. And here is a tip. Get a killswitch... and a better battery 3000 to 4600 mah is good!!!!. And!! Upgrade the steering servo.... jx 2060 is a good one and is pretty good for the money. And for gas!!! 40ml oil for 1L of fuel. And buy a good transmitter... i have a spektrum DX4C but there are cheaper ones. If you get these things my friend you are set!!! And!!!!! Better battery charger the IMAX B6 mini is prefect. Not the fake one butt the real one!! Check on youtube how to spot a real and a fake one. Have fun my friend!!!!!
@BajamanCam
@BajamanCam 12 жыл бұрын
Do you know anything about 2 stroke engines? A 4 shoe clutch does not improve high rpm, and a stuffer crank actually decreases top speed. I don't believe 85kph, put a gps on it or use a radar gun, and you'll get no more than 70kph... If you're running stock gearing that is. Obviously top speed does depend on track/road surface and tire choice as some have a different diameter, so don't point out the obvious mate. Good luck getting 110kph...
@SUPERFORMIAN
@SUPERFORMIAN 12 жыл бұрын
The engine in a car may not be a small engine, but it still must be broken-in. So do the 2-stroke gas engines for bicycles they have in California. Those must be broken-in.
@ashd002
@ashd002 12 жыл бұрын
Just to say mate you don't need to use a comma if you use the work ( and ) they serve the same purpose :)
@12th.jahlil
@12th.jahlil 10 жыл бұрын
Hey can you guys do a breaking in video
@tylarfoster3601
@tylarfoster3601 10 жыл бұрын
It's not hard to break it,in, just drive it around slowly and use a full tank and then it's all good
@12th.jahlil
@12th.jahlil 10 жыл бұрын
Tylar Foster now i know that. but im not getting an hpi product
@09166226xx
@09166226xx 12 жыл бұрын
i am living in VietNam,so can you ship it for me???
@ayansheikh1744
@ayansheikh1744 11 жыл бұрын
can we use the fuel from petrol station or we should make it plzz help
@MrGooseG
@MrGooseG 8 жыл бұрын
Yeah nah yeab nah
@claudekim7876
@claudekim7876 11 жыл бұрын
I think he forgot to loctite
@rcfunrc2112
@rcfunrc2112 12 жыл бұрын
Cool i love baja
@dominoespizza1756
@dominoespizza1756 4 жыл бұрын
this video demonstrates everything owners don't do
@BoardsProductions
@BoardsProductions 12 жыл бұрын
THISS i got it and its the best choice you can make
@CenaSitnica
@CenaSitnica 8 жыл бұрын
Guess this is a video for people who never had to run a 2/4 stroke gas engine, sounds a bit funny. lol
@Ldotbruv565
@Ldotbruv565 8 жыл бұрын
How is it funny??
@leeadamaa
@leeadamaa 14 жыл бұрын
standard 95 to 98?!!?!?!?!? i only get 89-92 octane content???
@crazyforcrcars
@crazyforcrcars 13 жыл бұрын
they should make a 30.5cc baja with 4wd
@MrTRISTANCOOL
@MrTRISTANCOOL 12 жыл бұрын
do i need to break it in?
@hallobyebye699
@hallobyebye699 5 жыл бұрын
Juppp
@bombakdik
@bombakdik 11 жыл бұрын
Why Fuelie and not Zenoah?
@hallobyebye699
@hallobyebye699 5 жыл бұрын
Saving money
@Sloppyjoe96
@Sloppyjoe96 12 жыл бұрын
what would happen if i ran the same gas from my weedeater in it?
@unknownguy1123
@unknownguy1123 10 жыл бұрын
Is the hpi stock radio reliable???
@quin1150
@quin1150 7 жыл бұрын
JRC i've had a runaway with it, so I don't use it anymore.
@GGobblin
@GGobblin 10 жыл бұрын
Standard octane is not 95 ! That is among the highest.... Let's be accurate...
@arttupiira9282
@arttupiira9282 9 жыл бұрын
+GGobblin It is in Europe
@gpaje
@gpaje 7 жыл бұрын
95 Octane RON, it similar to 91 Octane US rating system.
@AB-80X
@AB-80X 5 жыл бұрын
It's 95 RON, not 95 AKI.
@deletingsoonbye
@deletingsoonbye 11 жыл бұрын
95 octane? Nigga dis ain't a race track. Supreme is only 92/93 depending where ya go
@puella_meiberu
@puella_meiberu 10 жыл бұрын
Where I live, 95 is everywhere.
@reinier7865
@reinier7865 10 жыл бұрын
race fuel is 102 to 105 octane 95 is standard pump fuel
@flattabang
@flattabang 7 жыл бұрын
Well.. here 98 octane is kinda standard. :)
@MultiSniper70
@MultiSniper70 12 жыл бұрын
mate 91% octane can be used on high compresion engine like the 30.5cc engine which need a different oil mix ratio 32.1 mix any thing under 91% octane will screw a expensive engine so use 91% or 95% thats if you can get it becasue our gas staions in the uk have 91% and thay have 97% octane in other places but my nearest sells 91% octane which is plenty for what i need for a 30.5cc engine upgrade for a lozi 5t
@28minecraft
@28minecraft 12 жыл бұрын
They run on petrol (gas) and that 2 stroke oil!
@nicholasspears8052
@nicholasspears8052 7 жыл бұрын
"There is no danger of over priming the engine" is HORRIBLY wrong!!! You can easy flood an engine by over priming. other than that this video is spot on. But that comment is waaaayyy wrong, don't over prime ever. Over priming will foul plug and cause huge headaches!!!
@PommyDownUnder98
@PommyDownUnder98 12 жыл бұрын
its the same stuff. im not sure about the ratio mix you use but the engine is basically the same thing.
@kuwarchabba7624
@kuwarchabba7624 3 жыл бұрын
He said back and forward it doesn’t even go back 9:25
@jakelettera4443
@jakelettera4443 9 жыл бұрын
anyone watching in 2015
@WillBilly.
@WillBilly. 8 жыл бұрын
nope 2016 but i have watched this in 2015
@radmund17
@radmund17 8 жыл бұрын
Will Brewer I have to
@nanithefuck
@nanithefuck 7 жыл бұрын
2017 tho
@hallobyebye699
@hallobyebye699 5 жыл бұрын
2019🤦🏾‍♂️
@nitrorcfreak100
@nitrorcfreak100 13 жыл бұрын
That car looks bad ass fuck where did you buy that. I liked and I loved all of your videos so I had to subscribe. SONG??????????????/
@SUPERFORMIAN
@SUPERFORMIAN 12 жыл бұрын
Seems like they totally disregarded the break-in process. A fat birdie told me to break-in a Baja's gas engine, let it idle for 6 tanks. That's what I call time consuming.
@BajamanCam
@BajamanCam 12 жыл бұрын
110kph? Yeah sure... Unless you are running different gearing or a 2 speed. A standard baja will go no more the 60-70kph.
@eathynpatrick1601
@eathynpatrick1601 4 жыл бұрын
Is hard to put a 2 speed on them bro?
@Imperial_Wing
@Imperial_Wing 4 жыл бұрын
Put the car in the ground with the ra-radio turned on
@Hpj007
@Hpj007 12 жыл бұрын
there really isnt a break in rocess. and its not idiling 6 tanks of fuel. for the first tank you run it less then 3/4 throttle and very the entire tank. after that just run it like ya stole it.
@HaloofBlood1
@HaloofBlood1 10 жыл бұрын
receiver pack lasts for 15 mins and loads for 6 hours lol
@tarikparis11
@tarikparis11 9 жыл бұрын
no , 1h
@ethanmarsingill
@ethanmarsingill 9 жыл бұрын
no 55 min
@gbh7749
@gbh7749 9 жыл бұрын
+tarikتث paris 1كدسسبظبللدج
@DashzRight
@DashzRight 9 жыл бұрын
+dickvancock1 I also was like wtf, one gas tank of about 700ml and a "supposed" 2000mah battery last for 15 minutes powering 2 servos? But I also think he said FIFTY and not fifTEEEEEEEN
@puffmonster689
@puffmonster689 11 жыл бұрын
go with the setting they say 25:1 50:1 will hurt it
@HOOD-FM
@HOOD-FM 2 жыл бұрын
تصدقون ي اعيال ان السياره الي ف المقطع معي
@ibraheemalawnih7304
@ibraheemalawnih7304 Жыл бұрын
بتعرف فيهم ؟؟؟ .... انا من جديد شريت سيارة 29cc والبوجي يضل ينحرق .... في سبب معين لينحرق ؟؟؟
@savagefluxe
@savagefluxe 11 жыл бұрын
cool
@MARTINLARSENF0X
@MARTINLARSENF0X 12 жыл бұрын
if your unhappy with the speed. you can buy 62 cc engine, instead 26cc that comes with it. deal with it nooby.
@marclupian7544
@marclupian7544 7 жыл бұрын
1/5 rc car large scale
@Story-Taller-T
@Story-Taller-T 10 жыл бұрын
US $619.99
@Benny__4x4
@Benny__4x4 12 жыл бұрын
Baja.
@matteedstrom
@matteedstrom 10 жыл бұрын
WRONG!! There is one danger issue with over priming the engine, and that is if the intake of the cylinder is open and you prime it full then pull the cord. Most unlikely to happen but it can. Then you can actually bend the piston shaft! If unlucky.
@SnookTuned
@SnookTuned 6 жыл бұрын
WRONG!
@x-flight1015
@x-flight1015 9 жыл бұрын
100th comment!
@TeaBagger5000
@TeaBagger5000 12 жыл бұрын
They seem so boggy and kind of gutless.
@Redrocket2012
@Redrocket2012 12 жыл бұрын
those engines are generally broken in in the factory. but hpi is lazy and doesnt do it for you
@bradleymilton9372
@bradleymilton9372 11 ай бұрын
Hahaha this is ancient
@MARTINLARSENF0X
@MARTINLARSENF0X 12 жыл бұрын
i looked it up, and i hate it. its ugly and uncool.
@1091jordan
@1091jordan 12 жыл бұрын
I never said it definitely goes 110km/h, i said i could go up to 110km/h. Im running a stuffer crank and a lauterbacher 4 shoe racing clutch. My engine would maybe reach 85km/h but i have never cheked the actual performance of it. It also depends on what tyres your running and what conditions your running the baja on. If you use slicks and your on dry road then you willget a higher speed than if you were using dirt buster on grass or dirt. So when did you learn to troll fuck flaps
@blueharibo1
@blueharibo1 11 жыл бұрын
What put a geek on it? And a boring as hell voice commentator?
BIG FUN, Two ways! - HPI Baja5B Re-Release
6:46
Scale Builder's Guild
Рет қаралды 32 М.
Rovan Baja 5B 36cc Unboxing & Break-In
26:46
RC Addict's Garage
Рет қаралды 110 М.
VIP ACCESS
00:47
Natan por Aí
Рет қаралды 30 МЛН
coco在求救? #小丑 #天使 #shorts
00:29
好人小丑
Рет қаралды 120 МЛН
Une nouvelle voiture pour Noël 🥹
00:28
Nicocapone
Рет қаралды 9 МЛН
HPI Small Block Getting Started Guide
25:02
HPI Racing
Рет қаралды 379 М.
SWAPPING a 7.5HP ENGINE into my HPI Baja 5B!!
14:28
RC Knockout
Рет қаралды 8 М.
Beginners guide | Baja 5b, Rovan 1/5
15:40
C-MAN Adventures
Рет қаралды 2,3 М.
HPI Big Block Getting Started Guide
27:52
HPI Racing
Рет қаралды 544 М.
Tiny Train, Big Impact: Building a Coffee Table with a Twist!
28:48
Full Stack Woodworking
Рет қаралды 632 М.
This is Why YOU Love Tamiya!
33:19
Tomley RC
Рет қаралды 131 М.
Fixing my HPI BAJA 5B
9:15
RC Knockout
Рет қаралды 3,4 М.
HPI Baja- Brake Setup and Maintenance
9:07
Phatdadbaja5t
Рет қаралды 58 М.
Fifth-Scale Engine Break-In and Tuning
19:56
Sean O'Neill
Рет қаралды 213 М.