Awesome Info, good job ! Fixed my 0x2000 error by watching his other videos by replacing the gimbal ribbon, and now it is working like a charm.
@QCGUY3 жыл бұрын
My other channel?
@voc0073 жыл бұрын
@@QCGUY Meant to say other videos, my bad
@QCGUY3 жыл бұрын
@@voc007 People take our videos and put them on their channels so that’s why I asked. Part on me knew what you meant though. 👍🏻
@droneready82783 жыл бұрын
Giod stuff QC. Never owned a Zino...but I have eye balled them for a few years.🤔
@danielhonel68923 жыл бұрын
Hi Chris .... Thanks for the very detailed video! I'm definitely very much on April 23rd. We’re excited to see what’s new from hubsan ..... It could be a "Zino Ace" : 0) Kind regards Daniel
@jorgelucero8061Ай бұрын
I used the 0x0080 in my Zino 2 but what's minus me is to calibrate the Jimbal and restart Belbdron but I have to do that every time I want to fly with the drone.
@davidboscaljon37873 жыл бұрын
I just purchased a pro plus. having problems of it toilet bowling. also moves up and down left and right. I've done all the calibrations any thoughts?
@QCGUY3 жыл бұрын
The pro plus seems to have a lot of this going on. It has a new barometer which may be why it Bob’s around do much but toilet bowl is compass related. These are clunky birds that are calibration whores. It’s all about doing them right and never flying with less then 12 satellites.
@dragomataosp88623 жыл бұрын
great video as we are always together.
@genefoxgreenmountaindroning3 жыл бұрын
Great viedo and information thanks
@chrispeverell564310 ай бұрын
Hi Chris love your very informative videos I have a problem I made a balanced charge cable for my zino pro but it does not work on the zino Pro plus can you throw some light on this please
@QCGUY10 ай бұрын
That battery has a board in it that won’t allow you to balance charge unless you do a modification first which I have also done a video on.
Hello Chris, can u help me on the issue that Zino2+ not connecting to controller. Notthing comes on the controller display. Tried to bind new controller and old, on app there was no drone detected when press REFRESH. when push the bind hole button drone flashes. but cant bind. this drone never crashed. Please help me fix this issue, thanks
Hello Cris. I have a problem with the (Zino Pro +). Apparently everything works correctly, it does the check and it connects well, but there is no image from the FPV camera. The last day the drone flew a gust of downward wind caused the drone to hit the ground with some harshness. Since then I have no video image. Do you think the camera may have been damaged or if there is a solution. Thanks!! excellent channel
@QCGUY3 жыл бұрын
Definitely sounds like the image ribbon cable is done.... If it were me I wouldn’t think twice and just replace it. I have a video showing how to do it.
@erkemer3 жыл бұрын
@@QCGUY Thank you very much, I will look at it
@nicolasbil253 жыл бұрын
anyone have the error code 0x0002 on Zino pro plus?
@Webwalker093 жыл бұрын
I do
@robertjames67203 жыл бұрын
Did you find a fix? Mine just started giving that error today. I flew it in relatively high wind this morning (not sure if related). For about 20-30 seconds the camera either flipped to a weird angle or something and reported a gimbal failure. Then it went back to normal for the remainder of the flight. Tonight I was going to fly again - even remembered to remove the protective cover before powering on the Zino for a change. During the power up, the software reported a gimbal failure. The status page stated that the gimbal error was 0X0002. There was no crash/hard landing involved. Again, did you or anyone else find a fix?
@QCGUY2 жыл бұрын
Gimbal calibration tool sometimes is the fix for this code.
@joserosado5062 жыл бұрын
I have a zino pro plus, but I have error code x2000.
@bllueeyes3 жыл бұрын
Hello Chris ! I had an accident with my zino 117s, and of course the gimbal stopped working properly. Camera works but does not respond to command. A code 0X0800 is appearing on the screen. Do I have to change the communication stand? Thanks
@QCGUY2 жыл бұрын
If the gimbal doesn’t move at all then yes
@eliersalazar62052 жыл бұрын
Hi i already do the gimbal calibration with the gimbal calibration tool and the software, even i already replace the drivfer fpc cable i am pretty sure the cable is the correct because i scaned the QR code to know which type cable i need, but same error, the hubsan zino don't give a appropriate solution just say find on facebook, they don't have any official place to repair their drones on Mexico, I think even in the whole world it doesn't exist. Pretty bad I am very disappointed with the brand. Do you have any other idea how to fix this error? I really appreciate your help
@QCGUY2 жыл бұрын
If you ship it to me here in the US I can fix it. It’s hard for me to say what exactly is wrong with it in this conversation. Thanks
@user-st1do8uy4b11 ай бұрын
Do these fixes work for the EXO Blackhawk 2 Pro with code 0X0080? Which is a Hubsan Ace Pro. Any ideas on where to get a gimbal calibration cover for this drone? The site in your link shows sold out.
@QCGUY11 ай бұрын
The error code means the same thing but I think you need to use the hubsan tool app to calibrate it. kzbin.info/www/bejne/eXrdgGqVgq16d80si=EmrAFaMaBGmEaE-x
@user-wx3mv3kb7v3 жыл бұрын
I could not damage it, I carefully disassembled everything and collected it, if only a bad contact.
@user-wx3mv3kb7v3 жыл бұрын
hello tell me please I changed the front leg on the Hubsan zino pro quadcopter. and after the replacement the fpv signal disappeared. what could it be.
@QCGUY3 жыл бұрын
You most likely unplugged or damaged the image cable.
@edmacdronemanutec98862 жыл бұрын
I've changed the Zino 2+ cable and the Erro0x0080 continues, the app shows gyroscope error, so can I replace that component too?
@QCGUY2 жыл бұрын
I would especially if it won’t allow you to use the calibration tool. Generally that’s also needed when you see code 80.
@EACRivel2 жыл бұрын
hi Chris, Thanks for the Video, I have a doubt, on y Zino Pro The order is different, should do the same or there is any specific order? mine starts with Posicion 3 on Call ACC
@QCGUY2 жыл бұрын
It’s exactly the same process for all Zino’s under the zino 2 but doesn’t mean all act exactly the same. It will work on them all…👍🏻
@EACRivel2 жыл бұрын
@@QCGUY hey Chris I made the calibration but now I'm having the error0x0180, should I do the calibration again?
@QCGUY2 жыл бұрын
@@EACRivel never seen 0180… Do you mean 0080? If so yes do the calibration again.
@EACRivel2 жыл бұрын
@@QCGUY it was 0180, so I made the calibration again and it shows 080 again, the order of numbers it doesn't matter with the positions of the quad? Always same order of positions left side nose front, nose down, nose facing to me and then nose up and finally on the back, no matter what numbers shows the software or yes?
@QCGUY2 жыл бұрын
@@EACRivel I’m not 100% understanding your explanation but if you are doing it exactly how I do it in my calibration video away from any interference like magnetic interference from electronics then you should be fine unless there’s something else wrong there. It can take many try’s for some…
@breadelicious83543 жыл бұрын
Hi Chris, thanks for this video. The gimbal error 0x2000 happened right after I did the calibration using the cover and the calibration tool. On Zino Pro. Before it worked well. Could it be I should repeat the calibration multiple times? (tried 2x so far) Or it really means that the cable got damaged during the calibration? Find it unlikely since I was really gentle
@QCGUY3 жыл бұрын
Sorry for the late reply but it sounds like the cable has indeed failed if you have that code. If the gimbal is doing absolutely nothing on startup or after it’s started then it’s the cable. Gentle or not these just fail.
@breadelicious83543 жыл бұрын
@@QCGUY Thank you for your reply! I have already ordered a new one. However the weird thing is it moves during the calibration at the point when you let the device run through its access points and edges. It moves, but other than that, totally dead. Tried to reinstall many times. Will see if the cable helps when it arrives. Thanks again!
@QCGUY3 жыл бұрын
@@breadelicious8354 you may just need to calibrate it with the calibration tool and software.
@breadelicious83543 жыл бұрын
@@QCGUY Hi Chris, did all of that, bought the calibration cover. Tried to calibrate using the tool many times, did not work. Bought the new cable. Guess what, it's not the one. Even though my QR code doesn't say it is Y version, the cable inside actually is Y version. Ordered a new one, for the Y version and waiting for Chinese ti ship it. Nothing is easy when it comes to Hubsan :-)
@QCGUY3 жыл бұрын
@@breadelicious8354 Good times! 🙄 Takes patience with this company.
@sandpir83 жыл бұрын
I have a 0x2000 error right out of the box. They are shipping with bad cables?
@QCGUY3 жыл бұрын
It’s not uncommon sadly…
@slava30712 жыл бұрын
Hello! I have the same problem - 0x2000 error right out of the box. Have you solved it? Cable? I'm confused. I cannot imagine how the cable could be damaged during transportation if it is in a stationary state.
@sandpir82 жыл бұрын
@@slava3071 I purchased from Amaz** and sent the defective one back. The replacement was fine.
@HellRaZor1978 Жыл бұрын
Hey, first thx for all the help so far. But what about Zino2? I have video and the camera goes up and down at the start but then nothing other than video/picture. And some times after I press calibrate gimbal on my phone the 0x0080 is gone and says normal but still no movement from the gimbal. Do I still need the calibration tool? What should I do? It's driving me insane. :)
@QCGUY Жыл бұрын
The Zino 2 has a classic issue with its ribbon cable failing. Generally this effect video but it could be your gimbal issue as well. There could be dirt particles in the gimbal that you should try to blow out as well just to see.
@alangaxiola33977 ай бұрын
This is a great Video, i have a Hubsan ZINO PRO +, and i crash it, after a small repair on the back of the GImbal, i receive error 0x0800, i leave the drone for a few months and now trying to fix it, i receive error 0x0002, i start triyng to make the Calibration, and on the MC ALIGN the gimbal doesnt return to the center and fisnih as your video. Also the CAL ACC never starts. I just order and replace Motor flex, and get the calibration tool. I hope you can tell me what do you know about error 0x0002
@QCGUY6 ай бұрын
Did the cable fix the problem? That is what the error code was indicating. Issues with cable.
@alangaxiola33976 ай бұрын
Hello Chris, i had to change video flex this fix error 0x0002, after that calibration goes great as your video. After tests was successful i apply liquid tape and now drone like new. Now i am recovering my 2 batteries with the blue charger that you recommended (i did the mod for batteries) Thanks for all your videos and recommendations
@josephscott29073 жыл бұрын
This is totally off the subject of what you're talking about in this video. I have a hubsan Zino Pro . I bought it used flew iit a couple times. Quickly realize I needed new batteries for the drones so I ordered the 5000 battery. Also went ahead and bought new blades to put on there and Wi-Fi extenders. I get everything and get it put on the Drone Get Ready To Fly and it says data cable is not properly connected from the controller to the the phone. I buy another data cord it don't work. I buy a new remote and it don't work in the light on the side of the Drone is green not red or flashing red. Any words of wisdom cuz I could really use some help ready to give up on this hubsan not wasting a lot of money on it. Now I'm about to get the Fimi se?Was going to order zino pro plus but not after this
@QCGUY3 жыл бұрын
Did you bind the new controller to the quad when you tried it?
@shadg2693 жыл бұрын
I just bought the zino pro plus yesterday and I get USB connection error when it's plugged in my phone I can't figure it out
@QCGUY3 жыл бұрын
Android? If so make sure you are set to airplane mode. Other than that try a different cable.
@shadg2693 жыл бұрын
@@QCGUY its a Samsung note 10 ok ill try that thank you
@omarmorales47697 ай бұрын
Hello Chris I have the dame problem on my hubsan ACE SE R. It started with this error after update the firmware please I will appreciate you can help with this issue, the gimbal is not working😢
@QCGUY7 ай бұрын
The update heats up the gimbal cables sometimes depending on the update type and size so it sounds like it fried yours. If you want to send it to me I think I have one set of cables left and they aren’t easy to come by. Email if interested: qcguy.chris@gmail.com
@-Viceroy-3 жыл бұрын
Hubsan is a weird company. It's like these things are top secret information.
@tcibeatrecords47073 жыл бұрын
I'm having battery problems and camera problems with my zino.....can you please help.....
@QCGUY3 жыл бұрын
facebook.com/groups/HubsanQC/
@zambranojazualex3 жыл бұрын
Help me ... I have error 0x0002. I haven't been able to fix that error code for 2 months, and I thought it was the motor cable, so I changed the zino000-80 No2 ribbon, and everything remains the same :(
@QCGUY3 жыл бұрын
Join my group and post your information of your problem there. Thanks facebook.com/groups/HubsanQC/
@Webwalker093 жыл бұрын
Have you gotten it fixed because I have the same problem.
@alangaxiola33977 ай бұрын
i have the same error code, calibration procedure doent work on the CAL ACC
hi tell me i am getting an error - gyro sensor error- what is it that is broken? is it hard to repair (Hubsan Zino Pro Plus)
@QCGUY2 жыл бұрын
It’s almost always the gimbal cable but I can’t tell you without seeing it. If the gimbal is doing nothing I would get a new cable and install it if you are able to.
@cejko1974 Жыл бұрын
hi..when i try to callibrate my app just close by it self. Can you give some advise pls.
@QCGUY Жыл бұрын
You have to keep trying. It does it most on the pro plus and it’s frustrating but you just have to keep trying.
@arlansk8962 жыл бұрын
mine has the error 0x0080 you could write me a rest because I'm Brazilian then I'll have everything translated and see if I can solve it
@QCGUY2 жыл бұрын
That requires the gimbal tool and the calibration program on your computer. 👍🏻
@arlansk8962 жыл бұрын
@@QCGUY could you tell me which calibration program and how to do the same?
@QCGUY2 жыл бұрын
@@arlansk896 kzbin.info/www/bejne/d6HZaGCpa6unmtU
@arlansk8962 жыл бұрын
@@QCGUY obrigado
@waddac23 жыл бұрын
👍
@tarcisioscarparo47583 жыл бұрын
Good afternoon people. Today my one month old hubsan zino h117s stopped sending image to the app and started not recognizing the memory card, replaces the memory card and follows the same error. The rest are all working fine, stabilize the gimbal normally, move the camera, etc. The drone connects to the control, calibrates and flies normally. It just has that defect of missing image and card error. There was no fall or anything like that. Has anyone experienced this same problem? Any suggestion? Thanks.
@QCGUY3 жыл бұрын
It is the image cable. Replace the image cable and everything will be working again. I fix this problem a lot 👍🏻
@juanpablohuilihuili3 жыл бұрын
Hello friend qc guy, I am with the problem of error 0x2000 as I live in a distant country I do not have technical service available, I will do it with your videos, I need your help, could you answer me on facebook please
@ryansardes3682 Жыл бұрын
What is the software\app called plz
@QCGUY Жыл бұрын
For what please?
@conceptsCreativeStudio3 жыл бұрын
Funny enough I did not crash, was just performing the horizontal calibration and it went dead. Never powered on again
@upsidedownheadful2 жыл бұрын
can you help me on 0x0002 code
@QCGUY2 жыл бұрын
That’s a bad one I hate to see when repairing them for customers. Sometimes it’s the cable but often it’s a bad gimbal motor. Your gimbal is totally dead when you have this code so the first thing I do is replace the cable. You can’t buy just the gimbal motors but fortunately I have them. Good luck 👍🏻
@MadissonStudios3 жыл бұрын
Can you put bookmarks where each of the error codes are because you talk a lot.
@QCGUY3 жыл бұрын
A 10 minute video and you need bookmarks? 😂 Listen and you will learn at least two things buddy. Promise ☝️ I take the time to do this stuff as quickly and informative as possible. If it didn’t help you I’m sorry!