Husqvarna 2000 sewing machine - Setting the raise of the cam follower

  Рет қаралды 34,742

Absolute Sewing

Absolute Sewing

Күн бұрын

Пікірлер: 13
@karoncolligan2338
@karoncolligan2338 5 ай бұрын
Can you show me how to disassemble the upper tension disc, as the spring is compressed
@eliaelviraencisokuraica7370
@eliaelviraencisokuraica7370 2 жыл бұрын
Por favor, ¿podrían activar los subtítulos en español?, habemos gente de habla hispana muy interesados en su contenido. Gracias. 🙏🏻
@roararnevelle3636
@roararnevelle3636 Жыл бұрын
On my 6440 there is no exentric screw. One has to turn another screw. Best to find the service manual.
@katewinser8195
@katewinser8195 2 жыл бұрын
Help! Can anybody out there advise please? I fitted a new cam stack to a Viking 6570 but all it did was to produce a straight stitch in a wavy line. Took it out and put the old cracked one back in and the machine worked normally. I feel like I’m missing out something but can’t think what. I know the cracked one won’t last but now I’m stuck as to what to do . Any ideas very welcome.
@jennypatriciasandovalorteg2042
@jennypatriciasandovalorteg2042 5 жыл бұрын
hola...gracias por enseñar......cómo arreglo mi maquina cose al reves, hacia atras solamente. gracias!!!
@JoseRamirez-fq2sp
@JoseRamirez-fq2sp 7 жыл бұрын
hello could you tell me the circumference of the small belt of the engine and the amount of teeth where possible of the two belts that this machine uses .. since in Venezuela we do not have spare parts distributor and I need to locate a replacement belt or adapt another similar one in dimensions..thanks for your answer ... regards
@AxellTh
@AxellTh 9 жыл бұрын
Hi! I have a 6230. I have been repairing the pattern mechanism. Some teeth on the cogs where broken off. When set on zigzig, the cam follower when comming down from a lope it gets stuck on the edge on the next pattern in front and suddenly jumps off the edge. (hard to explain). It is only a fraction of a millimeter that the camfollower doesn't seem to be aligned with the cam. It is only happening when in zigzag modes. How do I adjust the alignment? Is there a screew or could this have anything to do with the cogwheels?
@papahonk
@papahonk 8 жыл бұрын
Hello, is that cam replaceable? after watching your video i was looking into the whole the lettered cam caps? pop into and noticed that the cam is snapped like yours. It sews great in a straight line but wont do a zig zag or any of the fancy stitches for more then a inch or to some none at all then goes to straight stitching. I really like this machine and would love to be able to do more with it. mine is a older two tone green unit thanks for any help you might have
@maureemcooper5911
@maureemcooper5911 9 жыл бұрын
How do I remove cam b from my Viking 2000 or can you direct me to a user manual, I don't have one with this machine. Its a syatem colourmatic. Many thanks
@kohmuffin4660
@kohmuffin4660 5 жыл бұрын
My cam A got stuck in Viking 2000 . Can please show me how to remove.. thank you
Ultimate 1958 Swedish Husqvarna Viking 2000 - Introduction
17:15
CowCountryVintageSewing MachinesAndRestoration
Рет қаралды 103 М.
Sigma Kid Mistake #funny #sigma
00:17
CRAZY GREAPA
Рет қаралды 29 МЛН
Quando eu quero Sushi (sem desperdiçar) 🍣
00:26
Los Wagners
Рет қаралды 14 МЛН
Table Talk 12 17 2024
21:27
Pine Needles Utah
Рет қаралды 44
Checking for zigzag on a straight stitch
3:31
Absolute Sewing
Рет қаралды 6 М.
Husqvarna 6000 series cam stack replacement.
7:01
Sailing Tess Bess & Sew far north, sail sew explor
Рет қаралды 6 М.
viking husqvarna 6440 sewing machine
12:24
Allen Dale
Рет қаралды 28 М.
HOMEMADE TOOLS YOU NEED TO HAVE.
13:50
PROFESSOR PARDAL BRASIL
Рет қаралды 250 М.
Saving a Potbelly Wood Burning Stove - Full Restoration Project
24:09
Rusty Shades Restoration
Рет қаралды 3 М.
Husqvarna Viking  Sewing Machine with Cams - Mike Culligan
29:57
giantdormouse
Рет қаралды 62 М.
Sigma Kid Mistake #funny #sigma
00:17
CRAZY GREAPA
Рет қаралды 29 МЛН