Thank you!!! Excellent presentation and explanation.
@Abubekerjemaludin2 жыл бұрын
Thank you very much sir that was quite helpfull
@pouchy4002 жыл бұрын
Great video. I do have a question? Can you rent a bottle and regulator? I’m a DIYer wanting to pressure test my car’s A/C system
@chrisE815 Жыл бұрын
Same question. I'm going to call a welding supplier soon
@Michiganbreadboyz_bt8919 Жыл бұрын
Fantastic video brother thank you
@Gwelds2 жыл бұрын
Thank you very much for this detailed video on regulators. Helped me a lot!
@paulanthony52746 ай бұрын
Hi, do you know if the regulator fits different size tanks? Or do you need a different size to screw into different tanks?
@felixwe9 Жыл бұрын
When pulling a vacuum on an existing system, will remaining refrigerant oil in the tubes affect your vacuum reading? In my mind the oil will evaporate just like water and ruin your vacuum reading?
@paulanthony52746 ай бұрын
Does the nitrogen regulator fit any size tank? Is it a standard fitting?
@GauravAgarwal2473 жыл бұрын
What type of hose pipe and connector you used?
@JW-qp5uf2 жыл бұрын
So the regulator is closed when it spins freely, not back seated counter clockwise? Also, is there a relief valve after the regulator?
@andygonzales94693 жыл бұрын
Good video easy to understand 👍🏼
@dicksonfu8604 Жыл бұрын
Do we need to tighten the regulator into cylinder a little harder than shown in the video (02:28)?
@johnkk78638 ай бұрын
Seems so
@konstantin9303 Жыл бұрын
If I leave it on by accident, how long would it take to empty the tank at maximum pressure?
@xXTECHxKNIGHTXx2 жыл бұрын
Awesome video! Thank you!
@marcdorizar57423 жыл бұрын
Very helpful thank you so much.
@rafaelserafico888310 ай бұрын
If you put nitro before you put pessured ,full ope valve on high side..then slowly open nitro regulator. .up to 150 psi.. check me if im wrong..then you see the low side .going up..to 150 psi . Then closed the nitro.
@jollyscaria19223 ай бұрын
Cylinder systom testing checking psi nigtgeon syslinnder nitgeon reualter fixing seting 2gueges fee gaugd open valvd afyone sidd psi seting other filling 100psi cher ac systom using 110 120 mord good condshion systom only 100 if ehg mor coper nes old bad dsmges 1000%expres out sidd jobed jolly hvac systom ok sir jolly
@carydrekkkk2 жыл бұрын
tightening (closing) the valve, increases the regulated pressure?? 🤔… shouldnt it be other way round as closing the valve kills the pressure
@jameswright4777 Жыл бұрын
awesome video thank you
@Vikis422 жыл бұрын
Sir ham 600psi peresure dety hin par suba kam hoa hota ha 560psi leakg b nhi ha ...kia masla ho skta ha
@albertcole79763 жыл бұрын
very helpful, thank you.
@mauricejohnson61234 жыл бұрын
Thank you so much!
@thecros10762 жыл бұрын
Can you tighten it all the way up , coz I need about 400-500 psi in my pressure system ?
@thecros10762 жыл бұрын
Is it possible to do so ?
@nickeberling1115 Жыл бұрын
Wonderfully done, thank you
@rossgarcia31123 жыл бұрын
Is that a 40cf or 60cf tank?
@toenyo3 жыл бұрын
HI Do you know the size of the regulator stem and thread size. I have seen 1/2 x 26 and 1/2 x 27 very confusing. thanks
@Z-Ack3 жыл бұрын
All nitrogen tanks have the same thread.. just like all oxygen tanks have reverse thread..
@chandanraj6043 Жыл бұрын
size of cylinder?
@rajendrabhatt3204 жыл бұрын
How much price to nitrogen gas regulator
@deenibeeniable2 жыл бұрын
How do you tell how much gas is left in the tank?
@SanjeevKumar00072 жыл бұрын
By checking the reading of pressure gauge on right side that read 2000psi
@deenibeeniable2 жыл бұрын
@@SanjeevKumar0007 So fractions of the tank will be proportional to 2000? Half tank = 1000 and so on?
@SanjeevKumar00072 жыл бұрын
@@deenibeeniable are you talking about pressure or volume.
@deenibeeniable2 жыл бұрын
Volume
@SanjeevKumar00072 жыл бұрын
@@deenibeeniable p1v1= p2v2 Where P1 is pressure in atmosphere ,V2 is volume you want to calculate, P2 pressure read by gauge and V2 is water capacity of the cylinder. For a gauge reading 1000psi , the volume of gas should be 1000*40(water capacity)/14.5
@modern-instrument Жыл бұрын
👍
@Z-Ack3 жыл бұрын
Couple hundred dollar regulator? Jeez.. unless you got a flow regulator with the whole float ball and comes with purge valve and over pressure releases.. i paid 35$ for my double gauge regulator.. works great..