Bridgeport Head and Base Lubrication Points

  Рет қаралды 28,966

H&W Machine Repair and Rebuilding

H&W Machine Repair and Rebuilding

Күн бұрын

Пікірлер
@buckinthetree1233
@buckinthetree1233 3 жыл бұрын
I really enjoy these videos. I don't believe I've ever watched one where I didn't learn something new. Thank you for sharing your time and knowledge.
@Blue2swing
@Blue2swing 2 жыл бұрын
Great video, thank you very much. You should consider adding links to your website, and direct links to all the items mentioned in the video-description to help buyers locate the products you sale easily. Thanks again for the great video.
@rickgabbard633
@rickgabbard633 3 жыл бұрын
Good job Barry. Thank you for sharing this valuable information. Retired hobby Bridgeport here in Kansas.
@jimhall3563
@jimhall3563 3 жыл бұрын
Thanks for this excellent description - way better than the manual.
@interpinto
@interpinto 3 жыл бұрын
Timely info. I just ordered a bunch of parts on Monday morning. Will be here Wednesday. Can't wait.
@arnoldsmachinetool4632
@arnoldsmachinetool4632 3 жыл бұрын
As always, Great video packed full of fantastic information. I don't think I have ever seen a shop tour of your place. Might make a good video.
@37yearsofanythingisenough39
@37yearsofanythingisenough39 4 ай бұрын
I have a set screw in the bottom of the table tee slot. I also have a hash mark on the front table edge in line with this set screw. I also have a hash mark on saddle that supports the table. When the two hash marks are aligned I can remove the set screw and drop oil through the set screw hole onto the cross feed nut lubricating it. I do not know if this is common to all Bridgeports or a previous owner added it. I also have a shallow round bottom trough milled all of the way around the periphery of the table which is extremely handy for laying drills, taps, and etc. so that they do not roll off when being exchanged, yet does not collect much in terms of swarf.
@HWMachRepair
@HWMachRepair 4 ай бұрын
The configuration that you have was common for the Zerk lubrication machines and is from the factory. Once Bridgeport went to the one shot lube they removed the set screw and the alignment marks. The biggest problem we see with that configuration is the way lube is designed to drip on the X screw, run around it and drip down to the Y screw but the line down to the Y screw gets blocked very quickly. -Barry
@WaynesWorldGarage
@WaynesWorldGarage 3 жыл бұрын
Barry, Thank you. Very informative video.
@hampdentime
@hampdentime 3 жыл бұрын
Thanks for passing on the information. Someday I hope to get my mill over to you guys to do a complete rebuild/ go thru. Thanks!
@mkegadgets4380
@mkegadgets4380 3 жыл бұрын
Could you please add a link to description on where to buy the oil and grease?
@mechanicsofcncmachinesandf4295
@mechanicsofcncmachinesandf4295 3 жыл бұрын
Nice informative videos
@GGPLAST3133
@GGPLAST3133 3 жыл бұрын
God job
@jeremiahmusser7707
@jeremiahmusser7707 29 күн бұрын
Would dte 24 work for the way oil?
@HWMachRepair
@HWMachRepair 28 күн бұрын
No, that is a hydraulic oil, which is what the spindle oil is. The issue is that hydraulic oil has no tact built in to help it stick to the way surface.
@jeremiahmusser7707
@jeremiahmusser7707 28 күн бұрын
@HWMachRepair OK, dte 24 would work for the spindle if I use a couple drops? Also, is there a good way oil you recommend
@HWMachRepair
@HWMachRepair 27 күн бұрын
@@jeremiahmusser7707 We sell way oil on our website, but any lightweight way oil will work. Do not go any thicker than Vactra 2 - machinerypartsdepot.com/product/way-oil/
@44Celt
@44Celt 3 жыл бұрын
Doesn''t the J head have a drop of heavy medium oil down the drawbar too
@buckinthetree1233
@buckinthetree1233 3 жыл бұрын
I read that somewhere at sometime. It could possibly say that on the lubrication instructions on the side of my machine. It says to lower the quill 2 inches and add a few drops of medium to heavy oil. I do it to my mill. I did however learn in this video that I am over lubricating my machine, and I also learned that my way oil may be a little too thick.
@SB-hi9nj
@SB-hi9nj 3 жыл бұрын
Read that too about a drop of oil down the drawbar. @Barry, does this need to be done?
@brandonlau3893
@brandonlau3893 Жыл бұрын
On the step pulley head, is it still spindle oil for the bull gear?
@HWMachRepair
@HWMachRepair Жыл бұрын
When we rebuild a head we pack the bull gear with EP-1 grease. There isn't a way to get to the bull gears on a step pulley externally which is why we recommend packing grease when the head is apart.
@brandonlau3893
@brandonlau3893 Жыл бұрын
@@HWMachRepair ok, I saw that in the video. Is the upper most oil cup filled with spindle oil?
@HWMachRepair
@HWMachRepair Жыл бұрын
@@brandonlau3893 That's correct
@brandonlau3893
@brandonlau3893 Жыл бұрын
@@HWMachRepair Thank you for the reply.
@fryloc359
@fryloc359 Жыл бұрын
How much to rebuild a step pulley head?
@HWMachRepair
@HWMachRepair Жыл бұрын
Usually between $1900-$2300. If you want a written quote you can email me at: support@hwmachinerepair.com
@thecaptain4740
@thecaptain4740 3 жыл бұрын
I have aquired a rosenfors milling machine very similar to a cincinnati #2 it was in storage for 15 years and was put there dirty i have to dismantle and clean can not find a manual any advice i live in bc canada. THANKS
@HWMachRepair
@HWMachRepair 3 жыл бұрын
I have a parts manual for the #2, but I can't get parts for it. There is a company called Parts-n-Parts that can get you parts, but they can be expensive. If you would like me to send you the manual you can email me at support@hwmachinerepair.com
@GGPLAST3133
@GGPLAST3133 3 жыл бұрын
Thik you
@GGPLAST3133
@GGPLAST3133 3 жыл бұрын
Think
Installing the Bijur B4867-A Flexible Hose Assembly
5:25
H&W Machine Repair and Rebuilding
Рет қаралды 4,3 М.
Bridgebort Milling Machine [Rescue]
35:43
Hand Tool Rescue
Рет қаралды 1,3 МЛН
黑天使被操控了#short #angel #clown
00:40
Super Beauty team
Рет қаралды 61 МЛН
The evil clown plays a prank on the angel
00:39
超人夫妇
Рет қаралды 53 МЛН
Cat mode and a glass of water #family #humor #fun
00:22
Kotiki_Z
Рет қаралды 42 МЛН
How to forge a bending fork. Blacksmith, Beginners.
13:00
Samuel the blacksmith
Рет қаралды 396
Oil Your Milling Machine, Don't Grease it!
5:25
Stuart de Haro
Рет қаралды 27 М.
Bridgeport J head Features and Functions
7:56
Moose's Machinery
Рет қаралды 3,5 М.
Replacing the Collet Alignment Screw on a Bridgeport
7:07
H&W Machine Repair and Rebuilding
Рет қаралды 17 М.
Disassembly of the Bridgeport Quill Housing
16:38
H&W Machine Repair and Rebuilding
Рет қаралды 116 М.
Shimming a Gib
11:22
H&W Machine Repair and Rebuilding
Рет қаралды 38 М.
How to square the Bridgeport head with the table
13:50
SuburbanTool Inc
Рет қаралды 182 М.
黑天使被操控了#short #angel #clown
00:40
Super Beauty team
Рет қаралды 61 МЛН