Hydraulic Cylinder Repair JD 300X Compact Loader

Just helping my uncle with a cylinder repair on his JD Compact tractor. Southern Maryland, USA

[@andrewmellon5072]

Thank you for another interesting and enjoyable video. Been in Murcia, Spain since late Feb no rain at all. Country in drought..

[@FarmerMD]

We have now had 2" of rain in the last 3 days so that will help our drought some.

[@frankscruggs4749]

Good video.

[@nickmurphy3935]

Having an issue getting rod back into cylinder after replacing seals, have an inch left, just can't get back in far into to put snap ring back in, any ideas?

[@gavinrackley392]

Thanks mate very helpful

[@josephyoung1635]

I just removed the inside snap ring, way easier. When you tap that collar down into the cylinder use wood instead of that chisel, harder to marr up important surfaces with wood

[@ghostyboy9469]

Hey fellas what size socket did you use to release the piston from the rod? 26 or a 28 mm?

[@jamesbell6765]

Good video. Does this piston and cylinder control the up/down axis or pivot on the bucket? Mine is leaking down on the pivot axis.

[@FarmerMD]

If I recall correctly this was the cylinder on the bucket pivot.

[@daningerman2872]

Can you please post what the part number on the bag was for the orange ring you inserted to get the cylinder out. Thank you Dan

[@FarmerMD]

H180788 - filler ring. $14.19 at my dealer. Good luck.

[@Guido_Sarducci007]

Rebuilding my cylinder from a JD 770 Compact. Thanks for explaining the orange ring. What a pain in the ass. I still prefer threaded end caps, with wrench flats. This design sucks.

[@wirenut9062]

Why should you have to put a new ring in to get the ram out?

[@FarmerMD]

it's the way it is designed

[@scotteyv]

Hey so did it end up fixing your leak, went through this same exact thing, broke my fitting, rewelded it, now I’m leaking. I thought the seal would be at the other end of the cylinder while I welded.

[@FarmerMD]

Yes it did fix the leak. Good luck!

[@scotteyv]

Cool thanks, gonna try it out next week once my seal kit gets here

[@FarmerMD]

Yes the leak is fixed

[@lavendermeadowsco.3447]

Worked great for me thanks. I ended up hooking the end of the rod to a ratchet strap between two poles in my barn, popped it out with quite a bit of pressure

[@dvljet]

This is why surge protectors and lighting rods are useful . its odd no fire because normally a lighting strike hits and you have a fire . has for the transformer their fused so if struck the fuse blows and transformer goes but beyond that a lighting strike should travel to the ground and disapate its energy if the ulity pole has a grounded wire . if lighting strikes your electrical panel odds are youll need to replace it along with the meter and mast and possibly the main entrance wires because chances are their damaged the power company usually will inspect their wires for damage right up to the entrance mast or meter socket after that a certified electricen should inspect the panel and all the wires because lighting is a way higher voltage than the 7.200 volts traveling on each phase of overhead wires . im actually shocked only the transformer went usually lighting strikes a pole and blows several transformers and switches not just one but at least 3 or 4 in a row it could blow 2 in either direction .

[@bobwhite825]

Maybe get a bigger hammer!😂

[@jhscheppele2448]

Ii’s because there is rust or dirt in the ring groove. I learned the hard way.

[@chargermopar]

When I saw you struggle with the Deere hydraulic cylinder I was thinking, why don't you strap it to the skid steer and lift the boom to pull the rod out. Not sure why they use that silly snap ring system.

[@FarmerMD]

I had to lay in bed one night to come up with a better plan, hence the reason for attaching between the 2 hitches of the pickups.

[@billperrey7934]

That design from JD is just another reason JD sucks.

[@FarmerMD]

Agree!

[@MrMitcam]

JD really did a terrible job on these cylinders and the whole snap ring removal idea. Obviously the input for that design was from someone who had never touched a hydraulic cylinder before.

[@jimgreen4504]

Mix up a little bondo for the snap ring groove .Works like a charm.

[@wisdomspitter7688]

I’m sitting here chuckling at your uncle’s enthusiasm about not having to use that rubber piece. It’s funny watching other people’s family and how they get along. JD looks as aggravating as any other brand I’ve seen. Blue, green, red, don’t really matter.

[@Cyclopsxwray]

Easier way is fill the groove with plaster of Paris. Then remove after

[@Blockycrypto]

the reason it did that to your uncles roof is because lightning actually comes from the ground to the sky not from the sky to the ground.