Hyundai elantra clutch master cylinder replacement | Hyndai Elantra 2012 hard to shift gears

[@AkashPandey-lc1lb]

You made it easy.....I can try with the old one now....thank you.....I live in canada too and you saved me a couple hundred bucks

[@herreraschannel8930]

glad it helped you!

[@AkashPandey-lc1lb]

Yes brother even if you need any help I am here to help

[@herreraschannel8930]

Thank you!

[@sylviagriffen639]

The clutch pin finally went on my 2005 Hyundai Elantra what do I order and how hard is it to replace it

[@herreraschannel8930]

@@sylviagriffen639 this only works on manual car. the model of your clutch master cylinder might be different from mine as it is 2005.

[@oidunno98]

Well done sir this appears to be the style on my 2010 forte that has gone bad. Great vid 👌

[@martl.4650]

Thank you so much my friend , I have a 2013 elantra gt and started to grind when going to reverse. I had the same wear issue and replacing the master cylinder solved it.

[@Sophie-go3ql]

Best video on this subject. Excellent explanation. Thank you

[@herreraschannel8930]

Glad it was helpful!

[@joedrew6533]

Just done this on my hyundai i40 ..64 plate ..and thanks saved hundreds of pounds ...👌

[@herreraschannel8930]

welcome! glad it helped!

[@sylviaisgod6947]

Thanks, I just replaced my clutch master cylinder, car is 13 years old 172k miles, it solved the gears crunching when I put on reverse. The hole was very worn out. BTW, there is a bleeder screw on the slave cylinder.

[@OriginalBernieBro]

Getting ready to perform this fix on 2015 Elantra, meanwhile my 2024 Santa Fe is back at the dealer with a leaking sunroof seems its draining into the windshield!

[@threedaysgracefanful]

Very helpful, thank you so much. Will be doing this repair to my 2013 Elantra coup soon

[@herreraschannel8930]

glad I helped! thank you for watching.

[@threedaysgracefanful]

@@herreraschannel8930 hey actually just one question, where is the clutch bleeder valve on the transmission? I was unable to find mine. I would legit be so grateful if you made a video explaining it

[@herreraschannel8930]

@@threedaysgracefanful there are 2 ways of bleeding it one on the master clutch cylinder and one infront of your engine almost in the middle part its hard to see it on top, you have to see the location underneath then open the valve from the top.

[@p3k4d0rproductionz]

Can I replace only the push rod that is woreout?

[@herreraschannel8930]

@@p3k4d0rproductionz unfortunately no you have to buy the whole clutch master cylinder.

[@measurram9236]

the video helps as mine just went out at a red light....that mixed with the fact my transmission fluid was way too low and wouldn't let me shift gears....yea big bad problem...thanks for the video though...now I'll know how to replace the part

[@travels_wright]

How did you know your transmission fluid was low and how did you fill it back up?

[@jabs8540]

Definitely useful, i might need to do this some time after replacing my clutch on my Elantra

[@herreraschannel8930]

yeah, the thing is wearing out again and I may have to replace it before the winter comes.

[@andymartinez1426]

Thanks for video my Veloster 2012 is already giving up

[@juansantos1336]

Hey! Thanks for the video. Hey do you know why would the clutch pad will wear out after replacing the master cylinder?

[@w4rf4c39]

It wouldn’t. The clutch pad likely was on it’s last leg. I suspect my clutch disc but I see my master leaking. I’m going to replace the master cylinder but anticipate having to also do the clutch if this doesn’t take care of it

[@falconsallday1825]

I just recently had my slave and master cylinders replaced. I was able to get pressure in the clutch after the repair but after sitting overnight, the problem with no pressure came back. My mechanic and i are really confused why this happened. Do you have any experience with this?

[@rolandolayvar4328]

Salamat po manong sa inyong video. Medyo mahirap na makita yung master cylinder sa engine bay.

[@Will-mx7gl]

Thanks bud , I have 2013 elentra gt ,I heard grind when I reversed , same problem , so I will replace it soon , Thanks

[@Mtl167]

Can you please explain how u bled the system

[@allaboutphones7488]

you dont need to just leave it open and it will bleed it self... press clutch few times with lip open

[@adriansicat8662]

Hi, Thanks for making this video. Yesterday, I was driving my elantra MT. I was on full stop and when the traffic light turned green, I had difficulty switching from neutral to first gear. I turned off my engine for 10secs, and started it again. The clutch went up automatically and I was able to switch the gear to 1st gear

[@herreraschannel8930]

check your clutch hydraulic the master or the slave one infront of the engine below the intake manifold.

[@abhishekdsilva9673]

Useful video mate. Thanks

[@martinolligarcia6337]

I buy a hyunday with thr clutch too low almost touch the back , I think can change...thanks for you advice my frien.

[@herreraschannel8930]

welcome!

[@ferryman4520]

I tried every fix including master and slave cyls, damper, it seems to last for a time but back to low bite.

[@herreraschannel8930]

yes because of the cheap plastic rod they use on the master cylinder. We just have to deal with it.

[@jaxonburt3670]

How did you bleed the master. Day two and I still can’t figure it out! Costing me more in renting a car then to take it to a mechanic.

[@herreraschannel8930]

what is the problem are you having right now? is it hard to get into gears? or you don't have pedal at all?

[@sylviaisgod6947]

There's a bleeder valve on the sl*ve cylinder

[@calebyounkin1001]

Is their some kinda clip or something other than the two bolts to get the master cylinder out I took the 2 bolts out and it still won't come out.

[@herreraschannel8930]

sorry this might be late but you have to twist the clutch cylinder clockwise and push it out.

[@GuyCook-i1b]

What happens when you can't push clutch pedal in after replacing master and slave clcindar

[@lowcabbie]

how long did it take?

[@herreraschannel8930]

I am sorry how long did it take? can you clarify it pls thank you.

[@markbibbins6813]

Thanks very helpful

[@dennismacaspac2516]

Boss anung dot ang fluid sa clutch master

[@herreraschannel8930]

kung ano ung dot flud nung brake mo un din ang gamit sa clutch master cylinder sir.

[@calebyounkin1001]

Please help 08 Elantra

[@herreraschannel8930]

what is the problem?

[@sylviagriffen639]

I need help with what to order. The clutch pin finally went today 2005 Elantra

[@herreraschannel8930]

@@sylviagriffen639 can you take a picture of the part?

[@jtoney4726]

Clutch pedal still stays on the floor after replacing have to pull pedal up no pressure building

[@beefcakees]

Haha, I can see the satisfaction of completing a job. Still a little confused on the bleeding..

[@herreraschannel8930]

yes especially if you saved a ton on labour and parts.

[@tofu7397]

I will say that if you replace this and are capable, fitting a metal bushing in the master cylinder rod wouldn't hurt. they wouldn't wear out if they weren't made from plastic or at least had a bushing. such a silly issue.

[@herreraschannel8930]

Yes that's what I thought but when I did that the center of the hole is not accurate it is in off position. Now it is starting to wear out again. That plastic rod.

[@sylviaisgod6947]

Clutch master cylinder $40 on Amazon.