I 3D Printed 1000 Death Korps Of Kreigsmen

[@battlebrothersam]

Get 12% off the equipment below using code: sam12 Sonic Mega 8K S: phrozen3d.net/xWsgJ Wash Mega S: phrozen3d.net/a8TaY Cure Mega S: phrozen3d.net/CDJbO Aqua Gray 8k: phrozen3d.net/SjVbd

[@the_brick_films]

Is there a smaller printer you would recommend? I looked at the old video of when you first started to print the death korps, and the 3d printer you recommend in that video is now out of stock if you could recommend one that will be great if not then oh well

[@ChrisR2020]

Maybe you could help me trouble shoot something. I had a failed print in my Sonic mighty 8k and it has been making noises at the start of the print on every print after it. Also, the early layers are all bunched up now. Do I need to replace my Z axis motor?

[@BenHyle]

1000 Kriegsman? Oh, so the first attack wave. Of thirty.

[@Bluecho4]

That day.

[@diplomat8482]

@@Bluecho4 During lunch

[@dantegaelach736]

In the second sector

[@PoorhammerPatreon]

@@dantegaelach736of vraks alone

[@owenmurray7588]

without artillery support

[@dalemoody8025]

Literally printing a new company per plate, glorious.

[@RoseKindred]

Right? I just imagine having a whole army of Blood Knights/Grave Gaurd from the older VC lists. Last I looked they were like 120 for 5 knights. FIVE! And you could not even make them all knights, it was 4 and 1 champion.

[@Bluecho4]

It's very appropriate, since Krieg are effectively mass produced soldiers. Even employing proscribed technology like Vita-Wombs (allegedly).

[@ClemiHW]

@@RoseKindred insane to believe back then plastic soldiers were made out of plastic because it was cheap

[@RoseKindred]

@@ClemiHW I am assuming the increase is from them shifting it to "finecast" aka, failcast (hey, I learned that term from one of their employees). Which is even more absurd because it does not cost that much to make 1 unit. I could understand if they redesigned the knights like they did the coach, but at the time they were the same model, just produced differently.

[@ClemiHW]

@@RoseKindred In France back in June they increased the price to 6% more, if that's because they're shifting to finecast then that's a huge loss I think most people are now switching to proxies and just use official merch for tournaments

[@tommygoodwin7240]

Next challenge should be printing an entire space marine chapter Helmets only

[@tommygoodwin7240]

Or chaos war band

[@alvaroaugustomeridio]

Next challenge is to make a video without using the word sonic or 8k

[@fuzztsimmers3415]

why

[@brayanfisk8769]

What about a full space marine legion

[@nikushim6665]

In before GW has a panic attack and sends out its team of lawyers.

[@G4rr0.]

Your mission, should you choose to accept it: Print out a life sized Kreigsman.

[@unknowncommenter6698]

I mean it took a lot of glue to assemble 3D-printed BFG9000 (yes I remember hearing that ID Software did in fact make a life sized copy of BFG9000 on a 3d printer), so I bet life sized Kriegsman would take a lot of effort to assemble and probably some steel rods as base.

[@vast9467]

yeah it would be easier to just make it out of other materials

[@fernandoarrellaga6035]

Don't know about your idea with those little ones, but you could made a tremendously epic diorama, with 1 or 2 titans and hundreds of death soldiers by their feets

[@Kids_Scissors]

Seeing that many miniatures all lined up like that on a print bed kinda reminds me of Emperor Qinshihuang's Mausoleum with the clay soldiers

[@richardpearce2186]

Be interesting to see a cost breakdown of 3d printing vs paying games workshops hyper inflated prices.

[@ThatPNWGuy2024]

Even the very first 3d printers could print faster than 80% of painters can even paint. These new huge ones for personal use you would easily print way more than you could ever paint.

[@RoseKindred]

I would be afraid of overloading a plate that size. Just surprising how much can fit, but one shift or wobble... or cat, and so much wasted time/resin. At least the bad prints do make good scatter terrain when cleaned.

[@lordnovas]

Modern printers are strong, pack your plate until you can't see the bottom of your build plate. You will maximize your use of resin

[@razelbliztkrieg3851]

My man made a entire army on his own to fight the heretic with the machine that the good emperor made using his bare hands

[@blissfulbadger]

New challenge: Print the full contents and expansions (and terrain!) of the new Epic, better than the box. And paint them. In a week.

[@tabletoppainter7390]

would it be difficult to make it a snapfit so it would be easier to asamble to the bases or arms?

[@cheeseant2574]

Noooo!!!!! You can’t do that! That’s $7000 for less than a pound of plastic! Nooooooo!

[@esurfrider7687]

If you’ve got some 3D modeling skills you could make use of the vertical build volume and stack the miniatures on towers, you could probably print close to 500 or more in 1 print provided that you had enough resin.

[@austersimon]

i dare to say that is not really worth it considering the resin use..

[@esurfrider7687]

@@austersimon agreed 👍🏻

[@TsarFrancisDrake]

It's amazing that, whether you go for a bottom-of-the-barrel 3d printer, or a top-of-the-line 8K XL printer, it's still far cheaper than buying the models from GW or Forge. It's just becomes a decision of how much money do you want to save.

[@joshuadtedd]

Can't wait for these files to be DMCA'ed by Games Workshop due to your video again!

[@RileyGein]

Grab em while you can so the creator has a bit of cash to tide them over after having their livelyhood destroyed

[@simonrobinson4761]

"For every one of us who falls...TEN MORE WILL TAKE HIS PLACE!"

[@col.hertford9855]

These are Valor Korps and are IP neutral. The issue with Krieg is they are pretty much exact copies of historical WW1 uniforms. Only the helmet badge is GW IP.

[@tweedle634]

GW's CEO is throwing punches in the air right now.

[@Curufinwex]

Did you consider aligning the torso and arms before printing, and printing each model whole? You could have done 10-20 different poses and that might have saved you all the hassle of gluing.

[@LordSlayne]

Battle Brother Snitch

[@jp53556]

What is the delicious purple liquid in the wash station ?

[@Ethan-ki9zc]

What kind of lights are those at 7:16?

[@Midwest_Idiot]

New to resin 3D printing, question might sound stupid; but wouldn't this print at a lower quality than a 8K mini due to the pixel density? If it's double the buildplate and prob lcd screen size at the same 8k resolution wouldn't this be more similar to printing in 4K on a mini?

[@faiir]

Yes

[@poldis3d]

6.5 hours for 1 plate of +-40mm minis ? I dont know your settings but they are very slow, mine will take 3 hours maximum for such plate.

[@sheynchapman9829]

What Kreig models are those? I'm just curious as I want to print those ones as well

[@Madlarkin00]

Just curious what slicer your using for this printer

[@marianocoutoune]

Creo que es chitubox

[@dylans7742]

I think you should print the basis for every Tau horde army! 1830pts of 60 Kroot Carnivores, 30 Kroot Farstalkers, 60 Breachers, 60 Strikers, 30 Pathfinders. 3 Recon Drones, 30 Gun Drones, 12 Support Turrets, and then add Shadowrun and a rando character.

[@alphawolf2993]

I need to start a youtube channel just for all the free printers you guys get...

[@Lesardah]

Brother, I think you just sold me on joining your Patreon. I owe you anyway - your advice this last year has saved me tons. And my Grey Knights thank you for it.

[@ipbk8471]

Where can i get the STLs. Sorry if i missed it in the video

[@malyxxplays7949]

i'm having so much trouble with my printer. sometimes the models arent even there and i have half a completed build plate! frustrating

[@TsarFrancisDrake]

Some slicers let you fuse model parts within the program itself before printing. Doing that could have saved you a good chunk of time gluing the parts together after printing.

[@glitchedprints9128]

Saves time building but opens up a whole new issue with orientation and snapping those thin gun barrels. For space marine models, definitely, for thinner figures better to stay safe and keep seperate

[@scottyboy6269]

​@glitchedprints9128 blend resin and they won't snap, are bendable etc

[@Henners1991]

Hey! Is there any reason you prefer Chitubox over Lychee? I find the former really janky and full of odd little glitches. Plus Lychee's new auto-support features seem to work so well (though you do need to give models a manual check at the end). My current workflow is; manually orient the model, use "magic" auto-supports, then use the "generate supports only on islands" feature (detailed island scan), manually add/alter any supports and then use the magic "Optimize" function. It's yet to cause me any major failures, though I did have an incident with a couple of halberds where I hadn't properly checked the bottoms of the blades.

[@boycie18]

Worst part of chitubox I'm finding is the camera movement rotating around objects in the scene. It doesn't rotate around what you've got selected and makes traversing it absolute hell...

[@maxwallace2123]

where'd you get the 3D models?

[@Henners1991]

For combatting the colder temperatures you mentioned, YMMV but I wouldn't recommend upping your exposure times across the board; I just increased the times on my initial burn-in layers (and upped the burn-inlayer count to 10, with 25 transitional layers). Thataway the machine and resin get headed up, but only the rafts are affected. I'd be too scared of affecting the quality of the miniatures if I messed with the print settings that actually affect them. I also have my printer in its own closed cabinet, that retains heat fairly well. Not sure if this affects anything all that much, but I also have an FDM printer at the base of the cabinet which I run a short job on first before any resin print, hoping it'll heat the space above a smidge. Perhaps it's just superstition! But I get it to print 10 small bases or something like that.

[@christopherdecock703]

So now that you can print a company at a time, how much are you charging for a plate?

[@NastyStankyChicken]

Dude at 8:09 is that a layered visual effect or is that super glue vapor.

[@carbonatedswag4244]

What website do you get your files from?

[@joancanario6377]

Hello, I'm new to this, important question, why not assemble the miniature in the 3D program and then print the complete figure? Or is there something I don't know about printing them in parts? I'm obviously talking about small miniatures like space marines. Greetings from the Dominican Republic

[@ovarb12]

What's the purple stuff you're using?

[@JacobWilliams-xe9hg]

whats that purple stuff in your wash

[@mikiangel95]

Have you tried the Uniformation GKtwo?

[@kye4216]

Wouldn’t this actually have a worse resolution since the screen is far bigger than the mini but both are 8k?

[@jacobmeader9704]

With all the new hype for the Legions Imperialis game for GW I’d vote to print an entire army in a bottle and compare it against the new plastic kits

[@benjaminrogers8875]

How do you know it's a high-end printer? It has a hinged door.

[@aaronmccullough4926]

If temperatures are critical for good prints, shouldnt they put a heater in there somewhere? I know very little about resin printing

[@johnlansdowne6050]

Here is a big test for you… in keeping with the Krieg theme. The Gnom medium artillery carriage. It’s on myminifactory the creator is Nate Feyma. The tractor in the front is the size of Super heavy Baneblade as is the tractor at the back. The gun is massive. The model takes 6 to 8 litres. I am in no way connected to the creators page I just found it and thought it was absolutely brilliant. Great channel by the way👏🏻

[@Blaz243]

How did you manage to print bases so nicely? Mine come warped or with weird artefacts in first layers. No other prints have this problem

[@michaelsmith8028]

Surely there will be an Imperator Titan print oneday. Even if it is just in 8mm scale for Legions Imperialis.

[@silentwarrior3]

How to get a cease and desist from GW speedrun any % 😂

[@IPrint3dMinis]

I would use it to print giant parts. I can see this as a way to mass produce, so now 3d Printers can make a lot more. Do you notice a quality loss at higher speeds?

[@masongrae5010]

I want to see you print a to scale ship for an army to come out of/be stored in

[@Basedweaboo]

Next challenge: Imperator class titan....I know of like maybe 2 files that exist but they are pretty easy to find. However a Astraeus Super-heavy Tank may be a nice print.

[@alphawolf2993]

Try to come up with a print that uses the entire Z axis to print regular soldiers. You can do this using tiered support layers but its very tricky! You could potentially do 1,000 kriegsmen in a single print.

[@MrSubsound90]

How are the fumes?

[@Hateweek1984]

I'm penut butter and jealous.... this is Epic AF!

[@battlebrothersam]

Haha thanks brother!

[@And-c7n]

You re going to paint them all?

[@L.Blaze_911]

Where are these krieg from ?

[@centurygaming3374]

If i had a 3D printer id do something like that I respect the grind sam

[@MusclePanda90]

Still wondrring how many printers you got lying around xD or you have to send them back?

[@notkonradcurze1347]

will ye ever print heresy brother?

[@battlebrothersam]

eventually, It's something I want to do

[@josgorens1234]

Which is the stl file?

[@GoldbergS1453]

Do you plan on making a video for Legions Imperialis?

[@mrward6510]

GW need to get a grip and drop prices to be anyway competitive

[@Henry-fd4dk]

Your next challenge should be a Necron tombworld that your Krieg army can fight (alongside your titans)

[@Senkiowa]

Surely, you have meant 1000 WarMänner figurines that you only intend to use algonside your other figurines from ConflictPolearm -40000k game, set in a colorful bright future.

[@ApexBovine]

Me, just scrolling: oh cool 1000 points of kreig isnt bad, I wonder- Batte Brother Sam: I'm printing 1000 kreig models. A whole company per plate. me: 0-0 oh...

[@Ashden96]

Here's a challenge for you: try not to get more STL creators into the GW crosshairs.

[@TsarFrancisDrake]

Nah, it's cool. Most STL creators offer their STLs for free when they're just copies of GW's stuff, so even if GW gets them banned off of Cults or Thingiverse, they lose nothing by just putting their models up on pirate sites, or websites based in countries that don't have strict copyright laws. All GW'll accomplish by going after them is just pissing them off.

[@jacko-san7570]

Print the entire Legions Imperialis starter box set, or a Titan in full?

[@GhostWarrior-v6w]

That’s insane did you end up painting them all ?

[@empeming]

Mighty 8k may be cool but still rocking the OG Mars 3 pro USB is what it’s all about

[@CJ-ur3fx]

5:58 - Why are those prints so glossy? High quality prints should have more of a matt finish. Glossy prints can be caused by using low quality resin, having incorrect exposure settings, or too much anti aliasing.

[@kanadaj3275]

Dirty IPA during cleanup or not enough washing can also cause glossy prints because the resin residue on the surface fills the microtexture that would result in a matte finish.

[@nickrivas6429]

Oh so these are those infamous Vitawombs!

[@sthom9461]

That's my patreon sub model over there on the far left. My hat's on crooked. Thanks, from one Sam to another. Also, recommended challenge: chaos kitbash. Choose two armies and Frankenstein enough models together to make a 500 point army. Adeptus Tau, Death Death Guard of Krieg, etc etc etc. It would be an experiment with creativity and using/printing alterations.

[@bon3tynormy]

can you get something to paint them all at once

[@nicolasweber1442]

What file did u use? I’ve Downloaded many great Krieg files, but never found any with that German spike on the helmet. Great video btw

[@augustusgraham3112]

it's the valour korp from The Makers Cult

[@augustusgraham3112]

They're by far the best and most modular Krieg models on the market. Best presupports ever.

[@RileyGein]

Get em while you can because Sam has essentially greenlit exterminatus on these models

[@JacksonRed]

maybe for your next challenge should be an ork gargant to go againts the warlord titan, not only would it be a great test for the printers but they would look amazing together on a shelf.

[@coupleofdevilskc3fu]

When is the necron army video coming? :c

[@noaht2125]

Sooooo this is where you team up with Eric’s Hobby Workshop for an epic collab with this… right? 👀

[@XorxoxTalarius]

So basically, I would be able to print whole EPIC army per plate. Not to mention whole Battlefleet Gothic fleet per plate :D Do want. But printer itself is bit expensive for me :D

[@MADSAHAD]

2 mins 7 seconds in and I needed to stop, I could hear Slaanesh whispering to me, tell me that I should be nothing but jealous of you and Khorne telling it could be mine only if I put one skull at the foot of his throne. Back down to my basement, I will throw out all of my childrens toys and my wife's stuff, I have no clue what any of it is and or does besides not help me print models. It starts now, for the Emperor!!!!

[@seanjones2524]

The Mega 8kS is selling for £1500. So I'd just go an buy the actual models and save the money rather than print my own, unless I wanted 2,000 figures, which I don't.

[@HumanbeingIthink]

You don't need the mega 8ks you could just get an elegoo mars 5 or another budget printer and it would work just fine

[@HumanbeingIthink]

Also mate you are not getting 1000 kriegsman for 1500

[@seanjones2524]

@@HumanbeingIthink "unless I wanted 2000 figures, which I dont"

[@HumanbeingIthink]

@@seanjones2524 still 1500 won't buy 1000 minitures so it would be worth it way before you reach 2000

[@seanjones2524]

@@HumanbeingIthink "...which I don't"

[@lolomistrzepik6167]

I think why not print 15 milion of krieg 😂

[@manny1manito2]

Oh you're using the Valour Korps Kriegsman! thats so nice i just bought them lets see how they turn out!!

[@dragonwyrmdracodracul8361]

New challenge? Life-sized dinosaur. Not the big ones, but a chicken-sized one. I think there are some nice STLs out there that are like that. The dinosaur could double as a unit for an exodite army.

[@BrotherBoot97]

*heavy gasmask breathing*

[@takedasamurai238]

I am way mental than you I have printed 4500 kriegs :D I love to see you did it. epic video

[@battlebrothersam]

wtf you mad lad!!!! well done!! LOL

[@HumanbeingIthink]

How much did it cost in resin?

[@SgtHouse]

Madness! Now print how many Baneblades super tanks on one plate!

[@Newblar]

Alright. Now paint them......lolol. JK man. This is awesome. Ive been looking into upgrading printers to an 8k.

[@americanman8251]

This must be the vetay woom technology used by kreig

[@gundam8655]

... UCV the brick all possible variants from this first entry to the Universal Carrier Vessel line.

[@AsianTrix]

Yes, yes. Make more, even more, and then a bunch MOAR!!!

[@gkr2189]

You sir are a wild man! I love it!

[@Aezarius]

Or maybe a Guard Armored Regiment ...tanks tanks everywhere

[@scottlidstone1902]

Sam's building his own Warhammer World, innit he? Crack on!

[@savage0gre670]

ok but now you have to paint 1000 minis xD

[@CompassionateCoos]

The real challenge is to paint them all!

[@Ollisaa6095]

print out 3 of each baneblade variant :)

[@battlebrothersam]

you madlad... maybe...

[@bengoacher4455]

Would be interesting to see the GW balance sheets and financial statements. I wonder if this is a genuine threat to their business or if they could do a Spotify thing where they release their own blueprints to 3D printer users for a fee that are actually legitimate. Especially if the majority of their money comes from black library, and computer games.

[@edimusprime]

that build plate is massive