got to do the same thing so thanks for showing me. this looks about as fun as pulling the motor out of my 13' awd ats caddy. PLEASE POST YOUR VIDEO OF INSTALL BACK IN!! want to see how big of a pain it is to get the input shaft of the trans lined up with the engine and push together.
@daren9721 Жыл бұрын
Thanks for the vid , I supercharged my z06 2 yrs ago now she's blowing white smoke and pressure through the vented oil cap . Probably a head gasket and piston rings . Time for forged components. 😅
@nickg0411 Жыл бұрын
doin the same exact job...the video is gonna help alot thanks!
@slightlymodified501 Жыл бұрын
No prob
@corvette3611 ай бұрын
Bought a C6 a few months ago. Timing chain snapped and junked everything 10 days after that. Should have it back soon.
@TheJimmy5454 Жыл бұрын
Andrew your the MAN!!
@KenchenZ06 Жыл бұрын
Nice video! Now I can go buy me a cheap c5🎉🎉
@artacosta3329 Жыл бұрын
Another one? Hahahaha, miss you bro. Love the video.
@slightlymodified501 Жыл бұрын
Hey Art!!! Hahah. You know me, gotta stay busy! Thanks bro, miss you too!
@j1mmys4ndusky Жыл бұрын
If you haven't put the engine back in yet I would recommend installing an external bleeder on the clutch slave cylinder!
@slightlymodified501 Жыл бұрын
Its been back in for a few months. I did do an external bleeder. Best $50 ever spent haha
@handyishrandyish334 Жыл бұрын
Did it go back in with exhaust manifolds on?
@slightlymodified501 Жыл бұрын
@@handyishrandyish334 It’s possible with them on but I left them off for more wiggle room
@dpmesseАй бұрын
I have a C5 with rear seal leak.... I have to pull the Tq tube/trans/diff, or the engine. ugh. All to get to a $10 part.
@handyishrandyish334 Жыл бұрын
More views needed! Great vid
@slightlymodified501 Жыл бұрын
Thank you!
@maxx236 Жыл бұрын
Just to reiterate, you didn’t move the steering rack to clear the engine getting out. Just removed the hard-lines at the front and unbolted the linkage below the alternator to allow the cradle to drop correct?
@slightlymodified501 Жыл бұрын
I was able to drop the cradle without unbolting the steering linkage. And yes I just removed that upper hardline so I wouldn’t damage it. The load leveler helped a ton tilting the engine to clear the rack!
@Zach-td5mb7 ай бұрын
I wanna watch but the eating sounds are driving me fuckin nuts
@slightlymodified5017 ай бұрын
Lol. My baddddd
@lelandcoberley8723 Жыл бұрын
Yup!
@jackalack7234 Жыл бұрын
How the hell did you get the damn thing off the drive shaft. I have spent 3 days trying to pull the motor off of the torque tube and no luck. Please help
@slightlymodified501 Жыл бұрын
Did you pull the bolts off the bell housing to engine or torque tube to bellhousing
@jackalack7234 Жыл бұрын
@@slightlymodified501eah man, all 7 bolts are off of the bell housing. I finally got the bell housing separated from the engine like an 1/8 inch with a pry bar, but it’s not coming out. I appreciate you replying
@handyishrandyish334 Жыл бұрын
I’m goin back in with mine next month is there any pointers or any thing I should leave off to make easier?
@slightlymodified501 Жыл бұрын
I actually have the video almost edited. I have been lagging. Went pretty smooth. Hardest part was mating the motor to the trans. Everything else went smoothly
@handyishrandyish334 Жыл бұрын
I await the vid! Thanks man
@handyishrandyish334 Жыл бұрын
Did you get it back in yet?
@castlegarage696910 ай бұрын
Ok thats loud that sounds like in top end but cant tell from a vidio metal in oil is not good..if sound goes away after warm its piston slap
@natez0690 Жыл бұрын
Any chance the noise is a worn loose bearing in the torque tube? Those make noise before they totally come apart and eat into the torque tube housing. Doesn’t sound like rod knock to me.
@slightlymodified501 Жыл бұрын
You are kind of right. It was not rod knock. The rod/main bearings were completely fine. There was brass colored metal in the oil and my engine guy said he found a worn out cam bearing. Not really sure at this point. I should probably check that torque tube tube though.
@handyishrandyish334 Жыл бұрын
Did you leave Bell housing on torque tube for install
@slightlymodified501 Жыл бұрын
I did, only because that was the way I removed it
@ryanfoster5742 Жыл бұрын
Good job man, any update?
@nzb3290 Жыл бұрын
Did you replace clutch too?
@slightlymodified501 Жыл бұрын
Yessir. Stage 2
@SLVRFOX88 Жыл бұрын
Found a cheap c5 that needs the engine installed give me a idea on how it would go back together
@slightlymodified501 Жыл бұрын
Cool!
@davidncw46135 ай бұрын
cool ty
@TCKBUBBA11 ай бұрын
Piston slap probably
@slightlymodified50111 ай бұрын
I thought so too. But why the metal in the oil?
@TCKBUBBA8 ай бұрын
@@slightlymodified501might e scored the cylinder walls a bit my car sounds exactly like what yours did seems fine been driving it since no issues whatsoever
@raysegura66695 ай бұрын
Shit man good job 👏🏼
@TheRMMFilms Жыл бұрын
i swear my man makes money just to buy himself more problems hahahaah