I fixed PC cooling.

[@Epsi1ong]

So from what we know about the Optimum cinematic universe he is Optimum Tech, Optimum Plays, Optimum Lifts, and Optimum Car Mods. This man can really do everything

[@AryaStarky]

I wanna marry him

[@LuisGustavoCP]

Optimus prime is the next one

[@RdTrpBrgr]

@@LuisGustavoCP*Optimum Prime

[@rudiruessel9816]

​@@AryaStarkyNo I want😮

[@juzzytin86]

And he has the face

[@zantardis]

A pre-built PC building company could make this their main feature as a concept and really take off. Great idea.

[@P1ayCrackThe5ky]

Ducts to vented case panels has been a thing for decades. This isn't a new concept by any means.

[@zantardis]

@@P1ayCrackThe5ky Doesn't matter, an idea doesn't have to be brand new to be a system seller. It just needs to be marketed well.

[@P1ayCrackThe5ky]

@@zantardis I stated a fact and you are arguing with yourself. You said great idea...it's not his idea or original. It also isn't going to take off. Good luck being delusional and naive...or get out of the basement and go outside. "I fixed PC cooling"...no, you didn't.

[@zantardis]

@@P1ayCrackThe5ky It sounded like you were trying to dismiss the idea as dumb with your first comment. If that wasn't the case I'm sorry for mis-interpreting you. I also didn't feel I was being abrasive with my previous comment, but if you read it as so it wasn't mean't with disrespect.

[@BeX32210]

​@@zantardis These things are pretty much standard in professional workstations and servers for - well - decades. There ist literally no point in marketing this stuff as "feature".

[@fletcherenfield9474]

Just a tip if you ever decide to revisit this or if anyone else tries this, look into using the "sweep" function as well. It lets you "sweep" a curve you've made along a path you've defined. That lets you make complex ducts with gradual curves more easily, and gradual curves are good for airflow.

[@ckngmad1357]

U mean like the inner side barrel gun? Create spinning tornado airflow?

[@Yarsig]

@@ckngmad1357 No. If you take a look at the finished product, 10:27, there's a lot of acute angles, and thus, sharp curves. This can disrupt airflow because the air will run into the angled surface much like a physical object and bounce off, creating turbulence and disrupting the flow of the air coming in behind it. When you have a gradual curve, (like a bell curve from a graph) air will travel much more smoothly, and 'slide' along the curve, rather than 'bounce' off an angle. Think of it like driving. If you take a sharp corner going 50, you'll smash into the guard rail. If you take a gradual curve going 50, you'll stay on the road without having to slowdown much, if at all. What you're saying is rifling, and I think that would actually harm airflow, rather than aid it. Rifling is useful for creating a stabilizing spiral on an object be ejected, (and yes, air) but the only real benefit would be if you're trying to aim the air at a distant target.

[@WolfgangAmadeus117]

That is not what he meant @@ckngmad1357

[@TheAliceQuo]

@@ckngmad1357 no, like a waterslide. his current design has angles which means the air will hit the walls and bounce off and cause turbulence. With curves instead it will create a laminar flow and increase the airflow significantly.

[@AntJets82]

Thank you for this

[@xxitz_pr0gxx631]

I saw someone else cover this in s YT short a few days ago. I liked the video, and I'm glad the algorithm blessed me with your long form video over this build!

[@trollidk]

Probably ztt

[@Cam-i]

Man this guy is dedicated to everything he does and I’m all for it

[@Cam-i]

@@phoenix1453 I'm confused by your question. I just love his videos.

[@Jamey_ETHZurich_TUe_Rulez]

He can cool cpu to sub ambient temp if he printed adapter which allows 16 fans to blow in parallel to that radiator. But he does only one fan as lenovo, dell and other premade pc manufacturers do it. So he is true original. ( sarcasm, last part )

[@QuirkyAvik]

you are making that judgement from video he to uploads, he decides everything about the video and thinks about it before uploading. this is not the real person even this guy would tell this to you. don't turn people into something impossible and then later fault them for that.

[@Cam-i]

@@QuirkyAvik alright

[@RobertIsaac]

I started doing this with cardboard and masking tape back in 1998. I spent more than a decade having people mock the low-key mods, but I also achieved some pretty epic overclocks. As you've identified in many videos before thhere are really only a couple of parts that are properly temperature-sensitive; the rest just need to be 'cool enough'. You've really added a great engineered look for the first time that I've seen. It's the same outcome as cardboard and tape, but the result is something I'd be happy to show off in a case modding context. The one lesson I learned the hard way was to not take incidental airflow away from the MOSFETs on the motherboard. Keep an eye on those temps for reliability, SSD and RAM aren't as big a drama that way. Looks like the airflow pattern from the top rear intake fan is probably doing an ideal job of keeping the key motherboard and RAM parts cool in this instance though.

[@mine5066]

Same. Recently modded my 10 year old PC with cardboard and OCed the CPU from 2.9 to 3.7 GHz. Cardboard (shoe cartons) and some tape are a really easy way to do this.

[@Slay_No_More]

I never modded my PC with cardboard but I admire the idea.

[@zaidlacksalastname4905]

​@@Slay_No_Moresame

[@fabianmuhlberger6153]

Those memories, it was a great time on overclockers

[@DEJ915]

I used posterboard when I did mine, thinner so easier to fit in the right places.

[@shoppster300]

This is actually awesome. I'm a 3D modeller/designer in the manufacturing industry and there are several ways to use the loft and shell commands to optimise your current design. Airflow clings to edges and 3D printing ridges and those straight lines would be causing some turbulence, decreasing the overall efficiency. I would be rounding everything possible to lessen this. However, you are 90% there and I'm definitely going to use this design methodology on my next build. I also have the advantage of 3D rendering skills so I can design this and also test how it will look before printing. Thanks for this idea!

[@arnoutdecock476]

I was thinking about the turbulence as well. Although it look nice to have straight ducts going through the case, they will not be the most effecient towards air flow. Also, fdm might not be the way to go to make the most productive parts.

[@benjaminoechsli1941]

I love when a community shares what it knows to fill in the gaps in individuals' expertise. If you do fine-tune the project, please let us know how it comes out!

[@s.a.f.7191]

I def want to try this, but my 3d printer is too tiny. Question though. I thought the same with curving the parts, but with such a short distance would the riges really cause that much of a difference?

[@esoel]

Please share your designs if you do! It would be great to see that!

[@char_noir]

@@arnoutdecock476 you can increase wall thickness and provide some kind of smooth transition for airflow inside, keeping oustide edgy

[@henryd4331]

I owned an HP server in a tower format that had similar contraptions inside. That PC is about 15 years old now and I always wondered why this hasn't become mainstream.

[@MichaelJacksonFromSega]

Because there are endless variations of hardware, cooling systems and cases that people use in their builds. And to make it go off you need something that will fit everyone's build which is nearly impossible and makes the process personalized each time which is increasing the cost of build too much for the consumer to be justified compared to the traditional ways of cooling systems. It also doesn't look as cool as when you have a clean build and can see all the parts lit up with rgbs. That's pretty much it.

[@dreykzero2549]

Enterprise hardware such as servers, workstations an etc always includes systems like this

[@thenozar7603]

As a mech engineer who's worked with Fusion360 heaps and on the uni racing team, this video couldn't have ticked more geek tickboxes. Love the car brag, certainly earned the rights

[@iamChermac]

This is definitely mech eng eye candy. I did my first degree 20+ years ago, so this video made me especially smile at how far accessibility of 3D modelling and rapid prototyping has come.

[@bocahdongo7769]

It's a painted love to design those thing to really nail the goddamn dimension and tolerance with almost zero trial. The skill I'm still struggle with until this day

[@adriansolis5362]

Man, this channel never ceases to amaze. Just pure curiosity, talent, engineering, and application (with excellent video production as a bonus).

[@Daeronicus]

I remember back in the 90s you could see PC cases with direct airflow designs all over the place. They were pretty awesome but very limited on what hardware you could use.

[@CASyHD.]

Still on Modern Systems. Just upgraded the pc from my girlfriend which had that.

[@MartinKrol]

Hp used to do this in their workstations. Not sure if they still do it or not. But it was a common thing on mid/ high end workstations. Hp z800 comes to mind

[@aker2KK]

Dell had is air shrouds as well.. even some generics cases had them in the Prescott era

[@kael13]

@@aker2KK Yup.. This is nothing new in the slightest. Mac Pros have them, too. I guess it could be deemed novel because you 3D print to fit your own parts.

[@chris_kazuki]

I think dell still does it in some of of there pcs

[@zachwright1819]

This is absolutely killer man.. I think this is a huge deal. Such an accessible idea, but its a proof of concept that payed off so well that it's impossible to ignore. The accessibility of this compared to water cooling solutions is night and day. Anybody with access to a 3D printer (even at their local library), a set of calipers, adn the willingness to spend a couple hours learning to model everything can take advantage of this and really push their hardware. I will be looking into doing this for my PC. The optimization opportunities are unreal with a 10 degree variance. Even just pushing it back up to the same temps afterwards would be some crazy performance upgrades. Good shit man

[@wattrash]

Did you do it ?

[@anofrommedog]

Such a massive improvement in CPU and GPU temps, would love to see some data posted on how the VRMs/RAM/other components are doing.

[@Chickenkeeper]

This, particularly M.2 SSDs too. And if there are rises in the temps of the other components is there a healthy middle ground that can be reached where everything either benefits or doesn't noticably change?

[@Rave.-]

Burning. They are burning.

[@brunogm]

Will try this without ducts to see if at least mobo components and CPU lower

[@kwinzman]

7:36

[@halomunkey]

@@kwinzman that graph is still from the 4090 actually (VRAM)

[@wani2000]

This has to be one of the absolutely best aesthetically looking tech videos of all time. Content value is also sky high as this was an awesome and impressive video to say the least! Well done Optimal Tech, keep this up and you'll be nr1 in no time!

[@RomanShein1978]

Aesthetically, maybe, but in technical terms it is not the best idea. The airflow is needed for RAM, VRM, chipset, and add-in cards.

[@DonOfAnn]

dude really said optimal tech when the name is right under the video 🤦‍♂

[@wani2000]

Who's got time to read properly these days. I also commented on my phone so it was probably autocorrected@@DonOfAnn

[@Y2Kvids]

Aesthetic wise , that British guy makes the best .

[@dfgdfg_]

@@Y2KvidsDIY Perks?

[@kvernesdotten]

There has been some stuff like this tried in the past commercially, but it never really succeeded. This is a super complex topic though, not only because fluid dynamics is a masters degree on its own, but you also have to account for all the other parts of the computer that needs some cooling, an almost infinite amount of hardware configurations, the fact that cooling with air is not the same as pushing air into a turbo for fuel, that there is another medium that actually transfers the heat between the source and the air you are moving, fire hazards, material science, the fact that people really like to see their components, convection etc etc. I have seen shrouds like this in the past (dont remember what company) but I like to think there is a reason why they never really took off and that the go-to solution for custom heat exchange is water cooling. But at least it goes to show that theres potential!

[@fubar12345]

Well put, should be upvoted more. I had a case in 2003 that had air flow ducting, I ended up removing it when I upgraded to a larger CPU cooler. As you noted, many parts - capacitors, memory modules etc. are intended to be cooled by the general air flow throughout the case.

[@LutraLovegood]

This was pretty common in the commercial space. For consumers though it's too expensive outside of prebuilts, there are too many possible configurations for anything but the simplest designs, and at that point you can do it yourself if you care that much about airflow.

[@8654ZuluFoxtrot]

I'm starting a new build and doing research on cooling. This was interesting but I doubt will work for the reasons you stated. I was going to post something similar, then saw your post. Well said!

[@Havok412]

​@@8654ZuluFoxtrot Honestly keep at it! In general the whole case's internals should be designed to allow for better airflow. Most cases are too boxy where the air will bounce around and cause turbulence. Also there's tones of gaps throughout most cases to allow different sized hardware to be mounted and things like the I/O slots in the back and if you don't have some positive pressure it will just suck in air and dust that further mess with the whole thing. PC case should look alien like on the inside if airflow is a top concern

[@brkbtjunkie]

The powermac g5 was very successful. They cooled 2 physical processors in the tower this way.

[@samchenmusik]

Your channel is SERIOUSLY underrated... Love your content!

[@rototype786]

Server hardware has been doing this for years and its good to see it finally implemented into desktops. I have seen some older dells and HPs that have intake ducts, but I think this is the first time I've seen a full intake/exhaust setup. Good job my guy! Well Done!

[@davidbischi]

seen it on plenty of OEM towers in computer labs while serviceing them. kind of a pain most often to take them out tho 😅

[@Kasapin5033]

Never Dells and HPs, as well as Lenovo workstations are still doing it. They achieve some impressive numbers with pretty small fans. Quiet too!

[@ryudeshi]

@@davidbischi yeah this is nothing new, every workstation in my school district has ducted airflow. My old Pentium 4 Dell tower when I was a kid also had a duct for the CPU cooler to channel cool air in and exhaust out the back.

[@Vanadium]

Haha I want to see the RAM and the m2 data for how good they can really work before performance tanks.

[@pianniello]

i was coming here to say the same - its an economies of scale thing for sure - if HP or Dell designs a server or desktop they plan on selling 900,000 units of, intake ducts are worth designing and paying for, but doing it on a full custom def is super cool. given that PCIe slots, etc are spacially designated by form factors like ATX, ITX, mATX etc. itd be interesting if case manufacturers were to do a bundle deal with cooler, ducts and case. doubt itll happen with how cheap AIOs are these days but still a neat idea.

[@williamhelena7592]

i love how you pivoted to start experimenting and incorporating new things with your channel. SFF is so awesome but it’s even more awesome seeing you talk to the entire PC community. Been a huge fan for YEARS. keep it up dude!

[@mythicul]

The production quality... it's just amazing

[@hagen9027]

it always is

[@mythicul]

@@hagen9027 of course, it gets me every time

[@steelresilience]

he's been this way for years. Its why I'm subscribed despite not watching everything.

[@bmwofboganville456]

Because he edits on a Mac - it has that professional look.

[@jlcgn]

@@bmwofboganville456😂😂😂

[@Pluuton]

Jeez good work! I am early into studying fluid mechanics which I am really interested in, and I can tell you, fluid mechanics but mostly dynamics is said to be the most difficult physics to simulate and understand. Just that you made this work and this well, even though there definitely are things that can be improved, is a super cool thing. Like the fact that you use the simple fact of just flipping the fans, so unconventional and smart. Again great work!

[@TheBlackBeltPanda]

I used to see ducts like this when working on PCs "back in the day", often times from the CPU cooler to a fan mounted on the side panel. Feels like we're coming full circle here XD

[@joseph_p]

Yea, a lot of hp and dells were like that. It makes sense to do stuff like that when mass producing computers. Makes less sense when all the components are custom.

[@Awen24]

This was my thinking too. I had a blue UV reactive shroud for my Athlon XP back in the day!

[@virtuallyreal]

When you have pre determined hardware it makes sense, even now oem will have some shrouding. You don't necessarily even need 3d printer, cad ( cardboard aided design ) will function just the same, when happy, with results, fiber glass it.

[@wnxdafriz]

it was common on the pentium slot card cpu's of the 90's (pretty sure pentium II's).. had a number of them which were more or less my payment when my friends and I used to help the local chapter eagle scouts the guys in charge of the group asked for people to donate their old pc's and we would go through and make the best possible builds out of what was available for people to buy (generally first pc's for grandparents in 2000-2003 time)

[@javiernlt]

My thoughts exactly, old pc's had those ducts: hp, dell and other manufactures.

[@raynjpg]

It used to be more common in older desktop PCs to have a dedicated airflow path for the CPU. My mom's old Windows Vista era PC has a scoop from one of the vents that shoots directly into the CPU fan.

[@Джимми-л1к]

Everything is new, well forgotten old. I hope I translated the old Russian proverb correctly into English.

[@McGreenBean]

i think it was common on older dell pcs at least i can remember dell using it alot in the early 2000s

[@raynjpg]

@@McGreenBean my mom's was an e-machine. pretty sure the company is defunct now.

[@xExekut3x]

bought an old dell optiplex off ebay that was like this. thought it was pretty interesting. and now seeing this, i'm wondering why this isn't more of a thing.

[@raynjpg]

@@xExekut3x one possibility is visual aesthetics. nothing pretty about a fat air duct shooting from the side panel to the CPU. a more likely explanation is diminishing returns. cooling solutions in computers have come very far from cheap fans and shitty heat syncs. these system integrators probably see solutions such as the aforementioned air duct as a waste of development time and money, being that they can get plenty capable cooling out of any regular CPU cooler off the market.

[@twistan4976]

optimum is the fucking goat man. Everything from video quality, quality of projects, to aesthetics are all top class. really pushing the barriers of tech videos, super sick

[@antaresvariant2306]

This is my first time watching one of his vids and I'm legitimately blown away by how beautifully-shot this video was.

[@tofu.delivery.]

and no midroll ads 🙏

[@poeticsilence047]

​​@EuanZhang That's because he has a "real" job outside of KZbin. This is more of a passion thing and it shows.

[@midgetazzy2584]

man the lengthsa u go to for each video is fricken nuts. no one does what u do man fricken love it. followed you since u had like 80,000 subs. also super keen to get my hands on your zero mouse

[@xK3NY0x]

This whole video is just awesome! The content, shots, editing, dedication are pure quality. No weird Intro with annoying music, no subscribe or bell icons with infuriating sound effects. I adore your content!

[@javiej]

I agree. Also without click bait, without boring sponsors and without "let's dive in" moment. Pure joy. Less is more.

[@samuraijaydee]

I did a simpler version of this a while ago, but what I LOVED about your approach was that you built the actually PC first then designed the parts to fit in the virtual machine... I'm going to give that a go. I also didn't know about that ducting tool, although I am only versed in TinkerCAD right now. Thanks for this video!

[@NightVisionOfficial]

Loft is common, if you used F360 for anything with a curve/direction that has a Start and an End you'll know already. It's cool to see your ideas come to life after years, by a youtuber x)

[@MrLukeMedia]

Tinkercad from experience is really limited. I'd recommend starting to learn F360, once you get mildly comfortable with it, it'll already be faster to use than tinkercad.

[@ge7468]

That was crazy. The quality, the editing and the project. Best tech channel right now.

[@Jumbro6]

Linus is out of the realm rn haha

[@palyze]

@@Jumbro6 this is better imo

[@chevyvette96]

totally agree

[@secretmountainlaboratory]

I always wondered if this would work; thanks for taking the time to test it out and prove some theories I had.

[@FlickTheBrick]

It’s pretty normal to see air vents on workstations and some prebuilt PCs. That being said, I really like this project. It was fun watching you combine your various skills with great results!

[@bigdumpfarts]

yeah, I was about to post that he built a Dell from my childhood/teen years but much classier looking

[@ionelum]

@@bigdumpfarts For me this reminds me the HP Workstations series 800 (with wich I worked for a decade) where everything was ducted in a much similar way to this build. Good job!

[@EstelonAgarwaen]

Was about to say, he made an optiplex

[@gmaacentralfounder]

@@EstelonAgarwaen With Pentium 4, no less. :-). This one Dell Optiplex PC had intake funnels and PC fan exhaust duct. All i know it was LOUD. I was toying with the idea of doing something similar (with added difficulty of not having 3D printer or easy access to one), but I passed. And since I watched the JTC's video on how liquid cooling on front intake reduces temperatures (and subsequently extending the lifetime) of every other component in the case, I wouldn't even bother considering...

I was going to rite the same. 😂

[@vagabond8460]

This channel seriously deserves so much more attention than it gets. Optimum brings a certain creativity that bigger channels lost their ability to produce in their content.

[@chrisgarciart]

Fr I can barely stand other tech KZbinrs at this point

[@poeticsilence047]

Once you see those dollar signs who cares about quality content...lol

[@cagneybillingsley2165]

if it was this simple, it'd be done already. people who make videos don't tend to be in the business of revolutionizing industries. well except maybe the mindless entertainment industry

[@BenyaminLorit]

Tunneling like this is one of those things/concepts that I'm sure a lot of us PC enthusiasts have at least briefly imagined in passing and dismissed. Seeing someone actually do it and make it come to life is kinda magical. 😄

[@ThePlacehole]

It used to be a common thing

[@jackson9415]

@@ThePlacehole yeah the older MacPros had it

[@manup1931]

It was pretty normal in prebuilds. But there were also cardboard mods for your GPU and stuff.

[@maciejbogusaw7274]

i actually saw something simmiliar in dell workstations

[@babs_III]

@@jackson9415 the new ones have it too, in fact, most high end workstations and many mass-produced prebuilts have it. It seems it's more a factor of justifying the injection molding costs that limit its use rather than creativity, and in many circumstances it's not worth the added cost.

[@JDFiv]

You're probably the most motivated and cool pc specialist on youtube. Huge respect for what you're doing!

[@CrazyPhys]

This guy is really bringing creativity to the area. And if you think about it, it's not hard to make flexible tubes which can adjust length to fit the hardware's layout.

[@ennayanne]

like those dryer tubes

[@noahbirdrevolution]

@@ennayanne My next build will now have a laundromat theme. lol

[@Kimboslot]

No disrespect, I love this cooling design, but my gateway computer from 2005 utilized the same technique.

[@ennayanne]

@@Kimboslot always ahead of their time

[@Ektuma]

​@@Kimboslotdamn than it feels like pc design went from performance and optimization to aesthetics somewhere down the line

[@Ali-hh6lo]

Another benefit is dust reduction from mixed airflow. This way dust protection would be much better and easy to clean up. Great video great content ! 👍🏻

[@leonardiyapp]

Yupppp

[@RUHappyATM]

Wonder why the pre-built PC companies (like Dell/Alienware) aren't really doing this.

[@Zero-wt7xf]

They do@@RUHappyATM

[@RUHappyATM]

@@Zero-wt7xf Only partially. I do remember the Dell Precision had a chimney/hood from the CPU heat sink to the rear...many years ago.

[@Zero-wt7xf]

HP did it for years, even more on the workstations. Open those up and you couldn't see one component until you removed all the ducting.@@RUHappyATM

[@UserCraft1]

these airflow guides are quite common on workstations and servers, great project!

[@Ober1kenobi]

Yeh it’s nothing new He came across something But yknow I Fixed, lol

[@beardalaxy]

i can imagine something sort of like this has to be similar to what consoles do too, yeah?

[@RannekoPlays]

I literally had a case that came with a shroud for airflow about 20 years ago

[@DuBstep115]

@@Ober1kenobi PCs modularity is its biggest strength and weakness at the same time. None of the parts are optimized, that's why a $400 console beats $800 pc

[@indiviiduall]

@@Ober1kenobihe prob meant he fixed it for himself

[@nathanrichardson2524]

I'm loving these more engineering focused projects! Keep up the good work

[@socialistape629]

Using paper or rubber gaskets might improve even more the performance ! This video was insanely good, bravo.

[@RegazozoGaming]

He could test with some tape before going through all that trouble.

[@simonvutov7575]

Just 3d print the case at this point mate

[@mauree1618]

now that you mention it. @@simonvutov7575 🤔

[@natearrigoni]

Printing a TPU gasket would take like 20 min. Nice.

[@LostRams]

Crazy how you keep a massive project like this to a 10 minute video. Amazing results

[@jmondanaro]

Most older server desktops had directed cowlings for fans blowing on the important components. I always wondered why they weren’t in PCs but I guess the variety of components means that they would always be custom. Thanks for 3d printers!

[@Lishtenbird]

They weren't ubiquitous, but they were there. One of my older systems had an adjustable side-panel duct to feed air directly into the CPU cooler, one of my tower coolers shipped with a flexible exhaust duct, and I remember later using a sheet of plastic to similarly force air through HDDs. But now, side panels are glass, so aesthetics just take priority.

[@squidwardo7074]

They aren't in pcs because it isn't necessary unless your computer is top of the line (in which case watercooling is a better option) or you are doing some serious overclocking

[@superthrustjon]

A year later, I watched this then and it came up on my feed today. To me, this is an absolute common sense cooling design and I can’t believe it’s not being done on prebuilts.

[@JaZoN_XD]

One thing you'd have to think about is RAM and SSD temperatures now that they get basically no airflow at all. Otherwise, this is definitely inspiring me to do something similar :)

[@ThePentosin]

There is still one intake and one exhaust that takes care of case temperature.

[@LumbChu]

This is actually a good point. The case being used I believe is actually designed for negative airflow which just means it's designed for pushing hot air out as the priority. That's why the front intake is actually routed from the opposite side panel. Positive airflow typically leave a mesh grill at the front for direct fan intake. Gamer nexus did a great video on negative airflow cases and the effects of jamming more fans in them. In this case(ha) I think if you were having high temps on ssd or ram already, this would not help those components if the case is truly a close air circuit.

[@bobbienl1]

Also VRM's and chipset. Especially with a 13900k in there

[@littleb9298]

dun worry, he will add some water cooling blocks to them in the next video...

[@meltech4659]

I dont think its a problem because the inside should be way cooler now because of the exhaust channels. And both the unchanneled fans are exclusively taking care of ram chipset etc., which is way more than in most builds

[@ebean9158]

OT, you've easily been my favorite tech youtuber for a while now. Thank you for mad shit like this.

[@Djent_Lover]

More mad shit like "strapping pc to audi roof, test temps" or "pc mounted inside bar fridge temp test" with mint cinematics

[@Redmage913]

“We have the LOUDEST passively-cooled PC setup for you today!” as the Audi zooms by at 90mph.

[@TheAdminFromHell]

If anyone makes this, make sure you still have airflow over the motherboard, you can run into a lot of weird system glitches if you get hotspots on your motherboard! The 2003 Mac G5, HP Z400 from 2009, Z420 from 2013/2014 all had airflow guides. (and probably every Workstation released since)

[@tobireindl]

Same as I thought. RAM slots and SSD drives need some "fresh air" too, so I guess you heat up the other stuff with this solution.

[@kajim8172]

yup

[@PBST_RAIDZ]

​Yeah plus its an nzxt case which are normally look pretty over perform well, I could see the working better with other cases though.

[@triliner254]

There are 2 system fans which are not connected to the ducts. So interior temp should be fine.

[@LordCohliani]

Not every fan was ducted so I think that's the point.

[@Fransenn]

funny thing is. fan ducting was common back in the y2k and in the 90s. so back to the future?

[@piersonm5574]

Would love to see a company do pre-builts like this, with stock hardware but custom ducts. That way you can always remove the ducts if you upgrade

[@gazpitchy]

Dell have always used vents in their desktops

[@PostingCringeOnMain]

@@gazpitchyI was 2 seconds away from saying that Dell Optiplex 755 systems from like.... 2007... had directional fan ducts in. Literally a shroud at the front and the back that surrounded the CPU block which meant they could run all day on a tiny, slow speed fan that didn't make a ton of noise when you had 100 of them all running in an open plan office.

[@alphadragongamingFTW]

Back in the day before people cared about how the interior of the PC looked and most PCs were solid and did not use any glass there were directional fans with Shrouds pushing air to a particular point.

[@flawns]

yeah ... Dell has been doing this since the 90s

[@robster7787]

Have you ever taken apart a Dell optiplex?

[@josecruz8803]

As a car enthusiast myself, I absolutely love this idea and way of thinking! Some notes though: -The rest of the parts/components on the motherboard need decent airflow too. The only air they are getting from this set up is from the bottom of the front fans blowing in, and the rear back fan is the exhaust fan for the case itself. With the GPU in the way the air is likely splitting the 1 intake fans airflow, best case scenario half towards the motherboard and half the glass (which is useless, and more than half is likely going this way). This could be fixed with a piece that moves air from that front fan directly to the motherboard. -The SSD must be an M.2 under one of those plates with the ROG eye on it, which does not look like is getting much airflow as is, meaning the SSD is getting much less from the one fan when it was likely used to getting it from the bottom fan (floor-fan? That's what I call mine) as well. -When you remember that he said he "drastically" reduced those fans speeds because they "aren't really doing anything", you start to realize the case isn't getting much airflow to the other components. Might want to make sure those are at a decent speed if they are not already. Still, an awesome video!

[@ov3rkill]

This. I was thinking the same especially the components VRM and southbridge as those things insanely heats up. Although modern motherboards have heatsinks on them, it would be great to see it properly dissipated too.

[@crawfordbrown75]

Smooth out those bends with a fillet, get as much laminar flow going in, and less static pressure will be required, airflow should improve significantly more on the CPU. (master of eng. - thesis on airflow in medical devices) - currently in that scenario the air will be separating massively, with lots of turbulent air only getting to the bottom half of the air cooler just so you know. Try and straight line the air as much as possible. Edit: P.s commented before watching

[@Meat__Sweats]

I was thinking the same thing, but At least with the current design, there isn't much space to round out the CPU duct because of the GPU duct competing for the same space. I'm sure there is a complex design that somehow smooths the curves of both, but it might be too much work for minimal pay-off.

[@DuyLeNguyen]

At these relatively low Reynolds number and mass flow rate, does it matter that much though (been about a decade since the last time I touched an analytical fluid dynamics textbook, but if memory serves right, it should not matter too much at this type of scale and ambient conditions)

[@ApacheVR-4]

I think that if I were to design something like this, I would have the Upper fan at the front of the case act as intake and the Top fan that he is currently using as intake for the CPU as the new exhaust for the GPU. You would have to get a bit more creative with making the 2 tubes move past one another, but you would get a much more direct airflow path for both CPU and GPU. Hell, you MIGHT even be able to use both top fans as exhaust for the GPU that way. It's worth noting that I think this is why most SFF cases do so well with thermals and smaller coolers compared to their larger tower brethren. Many SFF cases place the components where they bring in fresh air from one side and exhaust out the other side fairly efficiently.

[@rustler08]

@@DuyLeNguyen No, it's not going to matter that much

[@identity__thief]

Do remember the limits of 3d printers. Overhangs of >45° cause problems without supports

[@joshgrundon6019]

As an automotive engineer and giant pc nerd, this is the sickest thing i've ever seen. So cool man, and even cooler that it decreases temps by such a significant amount too!

[@FragEightyfive]

Some old systems had them, like 1990/early 00's when desktop processors started to need fans, through at least the early 2010's. I want to say HP and Compaq had some for sure. About 10-12 years ago I did a few different ducts to accommodate a few different sized fans. Worked great.

[@mesasone2280]

Ducting was pretty common in the modding scene in the early 2000s

[@TheSd1cko]

I had an old Dell in early 2000's that was given to me for parts / to mess about with and that too had ducted intakes and exhausts

[@squidwardo7074]

Yep. They don't need them anymore because CPUs are much more efficient now

[@MrMaxim]

You're doing amazing stuff and always pushing it. What a beautiful thing to see.

[@user-yu4ps3rh3p]

make content

[@omster_]

Hah didn't expect to see BananaMan himself here

[@CobraF1]

Fascinating and beautiful. I really like that modern car engine look with no wasted space. Really cool performance improvement!

[@gerarbasa]

MAN i need you to fix your keywords for this video. I saw a post about this months ago and wanted to rewatch it and lasted AGES!!! I need you to enhance your SEO 4 this video. IDK why, i searched through all search engines just to find it with fixing cooling. BRO!! "3d printed airflow fix pc" might be much much better keywords for this video. hope this help you get more and more views bcuz that project is AMAZING and MUST be a new standard in pc industry

[@scottdickson9224]

Bro I'd been kicking this idea around for years. Super, super stoked to see someone take it to the extreme. Excellent work mate.

[@shlubbert3355]

I've always been super intrigued by the airflow shrouds in server and workstation cases, so it's awesome to see you take a stab at this. Might be interesting to see how the airflow path could be improved further with alternative case layouts and component orientations.

[@LS-xb2fh]

I would love to see how cases with the PSU at the front (e.g. JONSBO D40) work in this regard. With bottom and rear intake and top exhaust, that layout allows both the CPU and GPU to get fresh air. But I have not found anyone who tested one of those cases with a back to front CPU cooler flow direction.

[@KalebSDay]

You truly are one of the best in class for presentation/editing. Thanks for making/sharing this! Super cool and aesthetically pleasing build :D Damn that performance & noise reduction is nice

[@dangahagan7645]

Still maybe my favorite video you've ever done. Hope to see some stuff like this again in the future.

[@BasicTriGuy]

How does this man not have more subs? His content is interesting, original, and pertinent. 10/10 love the output mate!

[@sykodelicninja4346]

He's growing nonstop, one day he will be huge and replace MKBHD

[@cjm5002]

The exact reason for that is the complete opposite of the giant tech channels: hes not a sellout shill!

[@theredscourge]

A note to anyone else attempting this - you need some airflow left for the VRMs on the motherboard and a little for RAM, SSDs, etc, so don't duct every single fan unless you've got a solution for those too.

[@rtopz1]

Seriously, too many shills here, giving mass praise when other parts need cooling

[@junkice6930]

Yeah, that’s the one glaring problem I see with this too. I’d be interested to see the difference in SSD temps/performance especially with this setup, as you’re getting almost zero airflow to it because of the manifolds. This is also one of the more heat sensitive components when it comes to longevity and can have massive consequences if it fails.

[@theredscourge]

@@rtopz1 Don't get me wrong, having dedicated fans for the CPU and GPU and ducting them is probably super efficient, but the PC builder definitely needs to leave at least one fan with no ducting unless these other components have MASSIVE heatsinks.

[@rtopz1]

@@theredscourge agreed

[@DerUnbekannte]

wonder if he'll see an nvme or something burning up in a few years because its heat sink is now blocked by the huge duct and there's basically no more circulation in the case

[@peter_parkour]

Been a while since I watched your videos, man. I gotta say you have significantly improved. This has been informative, clearly explained, and to the point. Stay humble and cool. I think you may be one of the best tech channels around right now.

[@danlazaro1676]

as much as i loved looking at your air intake and hearing the blow off valve, your fan ducts are by far the coolest thing I've seen in while! now I'm trying to think of custom parts for my PC to make it unique and functional.

[@itsanarse]

This is where a liquid cooled system comes into its own, the heat is immediately exhausted out of the case. Cooling ducts in PCs have been done for years by the likes of Dell and other OEMs, hell I even had my own 'cold air intake' in my PC back in 2009 made out of a Haribos tray. Always good to see some lovely 3D printed parts 👍

[@JosephKinney]

Yep. I went to liquid cooling about 9 years ago and haven’t looked back. I know that in that time, air coolers have definitely progressed (the Assassin he used in this video is a monster) but, so far, nothing has been able to pull me away.

[@pleaserespond3984]

And if you want even more airflow, you can route the pipes outside the case through a pci slot and put the radiator outside as well. You still want some airflow in the case for the drives, but this way the majority of the heat is immediately dumped outside.

[@shynnsup8383]

@@JosephKinney What are you talking about dude? Fans now a days are as good and quiet as liquid, and they almost never fail compared to liquid. Not to mention its cheaper, easier to build and upgrade, and you don't have the huge risk of flooding and destroying your entire pc. That alone should be enough.

[@ilyarepin7750]

@@JosephKinney if the air cooler breaks, you get a new one. If the water cooler breaks, your parts get soaked in water and fried. No thanks.

[@baal8938]

@@shynnsup8383 absolutely not lol. For GPUs it’s fine for CPUs it depends which one but it’s miles away when it comes to cooling. AiO is safe and almost as good as custom

[@sebastians1511]

always love how much effort goes into your videos. thank you for time that you put in them

[@serialtoon]

Pretty much the reason servers and some OEMs use these cowls. Gotta channel that airflow. Nice video

[@dgevert]

Yeah I instantly thought of OEMs like Dell and HP...they've been doing this for a while.

[@riopower]

my thought same but usually OEMs just draw airflow to CPU cooler but no exhaust like OT did. And look at the performance result. that looks like beating the AIO performance that has possibility of failure in long run.

[@nutty232]

you're my current favorite computer youtuber. thank you for the content!

[@peacelounge]

Some of the best content out in KZbin. As a product design engineer seeing your progress in fusion 360 is awesome.

[@walkinmn]

Ducts on PC modding should be way more popular, really well done. I'm just wondering about sound, would be nice if for a second video you could add noise levels all around because I would think the duct makes it louder but since some fans slowdown that would help, and in case it is louder, I'm guessing some dampening on the connections could help.

[@azur1o]

Since the ducts lead to better air flow which leads to lower fan speeds this should lead to lower noise levels for the same cooling effect.

[@gametime2473]

Ducts make quite a bit less sound.

[@GuitahLin]

This is so dope. Ducted fans have kind of been in my head for a while as I am also a car guy that loves PC gaming but, seeing it come to life in such a clean execution is so cool to see. All I'm wondering about this is the motherboard temps. As the most of the VRMs rely on passive airflow from air blowing about from the fans, I'm thinking in my head that they might not get enough of that and get pretty toasty.

[@tobireindl]

Also the RAM slots and all the storage drives need some fresh air too

[@bunnybag]

This concept is so good and the video is so well made that I've been watching this video regularly as of late.

[@mypeeps1965]

I remember back in the day a lot of pre-build's used to come with air ducting through-out but suffered from limited air intake/ventilation. Brilliant job Ali.

[@akusurejie_6826]

WERE NOW CLOSER INTO PUTTING A TURBO ON OUR PC

[@cocoiwnl]

This is kind of insane and a game changer. You've inspired me to attempt this on my 3d printer and learn fusion as well.

[@HotRatsAndTheStooges]

It really is. I would bet switching the CPU to the best performing AIO out there wouldn't even get you those kind of results. I'd happily eat my words though lol

[@MrDvneil]

no need, just setup intake rear fan, turn your cpu heatsink fans facing front case, and if youi have regular gpu, that would depends on your case, the best solution. well all depends on your case, not all cases have same posibilities.

[@echelonrank3927]

if still moving dirt around in 2023 is not insane and a game changer then i dunno what is he is bringing outdated PC dust accumulation technologies into the modern era of dyson led innovation.....

[@notquiteordinary]

I had an OEM computer from 2007 that did this, so....I'm glad to see you're really innovating here

[@Kazymedic]

Awesome video. This is actually how OEM PC makers like Dell used to make their stuff in the 90's.. Bravo on your efforts! I would buy this set up for sure.

[@jcgongavoe337]

HP workstations are still using them as well

[@robby98756]

I've seen them in servers a little more recent. Super cool (pun retroactively intended)

[@AsthmaQueen]

Yup mid 2000's xps systems even had channel guides

[@tasha1982ify]

DELL still uses it, HP too :)

[@jmckey]

Yep, I have a 10 year old Dell workstation PC with dual Xeons (it's mostly collecting dust now) that has these kind of custom directed plastic channels for the big aluminum heat sinks on the CPUs. There's actually no fans directly on the CPUs, just the airflow that gets pushed over the heatsinks via the channels. It's pretty neat and effective. Just very proprietary, like this setup.

[@Bboyman1150]

A lot of old Dell computers had great airflow paths. Specific the old Pentium D Dell Dimension and some SFF Optiplexes

[@picturemode4609]

Apple used to have it as well.

[@TechandTools1]

My alienware R3 has ducts, well channels inside. Really interesting case

[@itzyamancam8561]

Optimum never disappoints, easily my favorite tech tuber for over the past 2 years. Because of videos like this I’m always inspired to do more with my PC.

[@alwaysemployed656]

I got the same exact case for my production PC build. A lot of people shy away from this case model because of the sealed glass front panel. Mine does good. My personal method for cooling is sandwich several 120mm fans together then daisy chain the connectors so that the fan sandwich runs off the same connector. All OC tests never go above 70c temps. So, the Fan Sandwich method seems to work very well. Is having that many fans noisy? Not mine. I do believe that the fan sandwich moves air so fast, it also dissipates the sound at the same time.

[@Sinsanatis]

this man really does everything i swear. mf is the whole package

[@jrcoulter]

the most eligible bachelor. If i was a lady of a particular persuasion, I'd swoon.

[@Taiylim]

With time and money nearly everyone dedicated enough can. :) He is fortunate to be able to pursue all these hobbies so adamantly without much limitation.

[@Sal3600]

Wow relax people lmao

[@distorteduzi]

​@@TaiylimMany people forget about this if i had the money he has i would probably fo some crazy stuff too

[@user-vl4iq7bj5e]

i really admire how you tackled the problem in your own way with inspiration from working on your car. would love to see you do more projects like this. lets try some custom liquid cooling on the cpu, gpu & ram next?

[@scottlayton2327]

A clean, visually pleasing and dare I say elegant and efficiency look that I'd reckon even Apple would envy. Very nice

[@jylpah]

Super impressive! It’s long time since really heard about innovation in PC case cooling 💡. I have a full mesh case, 360mm AIO cooler for CPU in front sucking air in and top- and back fans pulling air out of the case. Initial plan was to put the AIO at top, but it didn’t fit. Now I suspect that the air just gets stuck inside the case without clear airflow. This video got me thinking how the air is actually moving inside the case.

[@hodgiwabi]

I work at Autodesk, and things like this is why. So cool to see what people do with F360. Looks like a sick build.

[@Y2Kvids]

I also work at Desk .

[@karimsherali3764]

Used auto desk for years in engineering academy at highschool lol

[@Kinvesu]

I also work at autodesk.

[@lachyjp]

As a fellow Bambu X1C owner, I recommend use the Gyroid infill option instead of Grid! It can print less noisy (the head can scratch the infill on grid sometimes) and lessens the chance of tipping over the model. Also, be careful using PLA parts in PCs, tends to warp around 60-65c. Not sure if that is PLA or not you've used. I might still this idea for my own PC, love your content as always!

[@bob38028]

If you’re gonna do it for your GPU make sure you have a Founders Edition card with the instead of just the double tan design that most cards use! That’s really the only reason I believed his manifold is achieving a proper seal with his GPU.

[@joey_f4ke238]

I'm using pla for a gpu duct on my pc and it has been working fine for a year now, the cores might go over 60c but the air coming out of the pc practically never will reach even close to that, it would be 30-40c when it exits the case, unless you are severely lacking ventilation and the pc tower has become an actual oven

[@michaeldethomasis257]

This was a great video keep up the good work man! love to see a bit of car inspired design and engineering mesh with other fields!

[@friendlysurveillancecamera6507]

I had the same idea as you. Today, I'm shopping for a CPU cooling fan, and I've been thinking that to maximize the cooling airflow, it would be better for the fan to go through a smaller opening. It's just a theory I had, and then I stumbled upon your video. It was really great! This concept reminds me of the Venturi effect, where air passing through a smaller opening creates a more focused and cooler airflow, similar to blowing air through pursed lips instead of an open mouth. Thank you

[@FiveMissiles]

interesting because i had this idea about gpus and how they are all semi unique because its hard to replicate a dye and then linus recently posted a video about the same idea but w cpus

[@kfiz9502]

Forcing air through a smaller opening does not reduce air temperature rather it increases velocity. One perceives the air is cooler due to the increased velocity. Think of it this way. The faster you spin a fan (increase velocity), the cooler the air feels yet the air temperature did not change.

[@Ageis86]

This has been done many times before and is a well-known way to cool a PC. But you have a cool take on it, and it looks great! Good job. I used ventilation hose back in 2005-ish to cool my PC.

[@MAXTORRACER]

I was thinking the same thing. I did this back in the late 90s with $3 in pvc pipe from home depot.

[@greatwavefan397]

haha cool take

[@Salamanii]

That's exactly what I thought, I love that we've gone full circle now

[@austinn5877]

I took apart some old Dells years ago that did this for one or two components with some proprietary blue plastic bits.

[@omarassadi2455]

Lol, was thinking the same thing; my Supermicro CSE-836 from like ~13 years ago has a massive shroud to guide the air from the fanwall over the memory, VRM, CPUs, etc. I think the video does a good job showing the average person how much of a difference ducting can make, but the title is very click-baity.

[@ChristopherWoods]

HP, Dell, Lenovo all do this for HEDT and server stuff, but I've always thought with the sort of temps we're dealing with now that this sort of arrangement with flexible connectors could work well for people who want to extract the most from their air cooling system and partition the hot and cold paths. Great vid, and nice five pot ;-)

[@PedroFerrer-vq5sw]

HP, dell and Lenovo also did this on high end workstations like the HP Z620 for ram and cpu cooling

[@xzaz2]

HP and dell even did (?) this for their small office pc's

[@ShreddedShredder0]

I've always wanted to do something like this. I got my inspiration from Dell's own ducts they use on their desktops. You executed it really well.

[@kaktokakto7087]

The biggest problem with this mod is the vram/ram/ssd cooling, and to be honest the way to get simmular results is open air case, aka open air benchmark, if you one a 3d printer you can try something like opf-1/ii/3

[@SreenikethanI]

@@kaktokakto7087 same thoughts

[@HeavenlyPalace-Y2K]

This looks aesthetically pleasing. I did the same mod, except with cardboard and masking tape.

[@brentius]

Very cool, but it would be be interesting to do this in a SFF pc (like the Fractal Terra or the Dan C4SFX). I guess the gains like that would be bigger?

[@zambuzan]

And where would you place ducting in those cases? Literally no leftover space with a full built system in those form factors

[@Felale]

For those it doesn't make sense to do anything but water cooling.

[@DZ-jm1my]

​@@zambuzanEven very short ducts are beneficial, from my knowledge. I'd love to know, though.

[@tanphan1848]

Funny thing is that its a little bit easier to do this on small itx cases. Got a friend with a sandwich setup, he built tunnel for his CPU and it works extremely well. Theres no need to build one for the GPU since its right next to the mesh, all the air is fresh from the outside.

[@Nunkuruji]

This is the aspect of SFF that I find attractive. Many of these designs have the CPU/GPU drawing fresh air directly. What's beneficial isn't necessarily a full duct, but possibly just a gap bridge like the Noctua NA-FD1. The ducts are akin to data center industrial design, which often are also brute forcing with delta fans (wear ear protection in the data center). One could also imagine doing something like not having fans on the CPU tower, and just having them at the ingress/egress of the duct, or removing/replacing GPU fans and ducting the air in a unique way. All of this affects turbulence and perceived noise in different ways, which may or may not always be acoustically pleasant. I'd also be concerned here about the airflow the VRM & RAM are getting.

[@okage_]

your videos get better everytime! keep it up man this was insane

[@endergolem9977]

Even though it's not easily accessible to regular PC enthusiasts, it's a beautiful proof of concept that can really go far. I can envision a small community of 3D printers making custom designs like you did, sprouting up and helping out people who want better cooling. It's honestly brilliant

[@Boris-Vasiliev]

Use cardboard or some plastic sheets instead. Its just an air duct, no need for structural strength ot high precision.

[@froooty3309]

@@Boris-Vasiliev I agree that it can work just as well like that, but I think this is more about how clean and well done this is. Many enthusiasts care about the aesthetics of their computers, and this looks incredible while still being a huge performance uptick

[@sierraecho884]

That´s exactly what I do...

[@wollinger]

Proof of concept....lol

[@Tankashi0]

this is one of most amazing projects i have ever seen put imagine if you made it with clear plastic that would have been amazingly good looking

[@bloomfield295]

With every video this guys is pushing it. Glad to see just a single person crew is making all this possible and other tech channel like linus with all man power and what not are not thinking innovatively. The content this guy is producing is getting better with every video.

[@Mr-R.R.]

linus tech tips isn't about making unique tech stuff lmao what a weird comparison

[@xplat]

Quality over quantity. Linus has to pump videos out constantly to pay his employees. This is more of a passion project for Ali at this point, much like his PC builds and car mods.

[@BilalKhan-zl4vr]

Love your videos man. You really encapsulate what an enthusiast wonders about, and then actually do it rather than wait for the industry. Keep it up❤

[@levistoner]

You can DIY this pretty simply and cheaply with some thin cardboard like cereal boxes or soda cases and some duct tape. I did it years ago on my AMD FX rig, those cpus were known to be little toaster ovens, and it worked great. Dropped the case temp a lot since the cpu and gpu each had their own intake and exhaust vents.

[@MaxBechdel]

I'd love to see that in a like a current $3000 build, and have it showing 10-degree drops or something. Low tech can be high-tech!

[@nicspits9876]

Same for the first I series in 2010, spray painting the cardboard after cutting the pieces, then some nail stenciled logos, looked neat... then I went back to watercooling and a mid case LED fan velcro'd on the non-visible sides to blow up and into the graphics card... :D

[@XavierBetoN]

I did the same air channeling with the idea of "one fan cools the chip, means one fan can take the heat out" got even better results. Now I start to hate 10-fan computer cases that can't cool but just induce dust and brute force and consume unnecesary power and produce noise for no reason just to watch some RGBs. People don't think at all, they just want turning things with lights. Thanks for making a great explanation about this.

[@fermitupoupon1754]

We used to do this in the 90s with cardboard and craft paper. Then we graduated to custom loops with external radiators. The latter is still my preferred way of doing things. Though it is so much more expensive than some cardboard, it's also so much more effective.

[@mordorson]

Wouldn't water cooling do the same thing as this? Since the radiators are mounted directly to the case fan and all the air flow is being forced through them, it makes sense to me at least.

[@fermitupoupon1754]

@@mordorson this chokes out the case, there's going to be very little residual airflow to cool all of the other things in a system that do need to get rid of some amount of heat. Water cooling doesn't do that. Then there's the bit where my loop can passively dissipate about 100W through the external radiator. There's no way a couple 3d-printed ducts are going to get you that kind of performance. When things like a MoRa or Cuplex Gigant come into the picture, there is very little that can beat water cooling for when it comes to passively cooling even a high end system. It's expensive, that's for sure, but it's extremely effective.

[@leonidastankiangaming]

I love how sleek and clean the design is. My only concern is the temps on other components like the nvme drives and the RAM and the VRMs on the motherboard. Did you take notes of those numbers before and after the mod? I'm genuinely curious.

[@LuLeBe]

This! The thermal design of those expects a normal case with airflow, and not a hotbox with no airflow at all.

[@zl_390]

He did have two case fan, one on top and one on front that's left open wonder if that's enough to provide some airflow to the ram and vrms

[@leonidastankiangaming]

@@zl_390 but those vents obstruct a lot of the air flowing directly to the motherboard. Also he can get way better results with CPU temps by just setting the rear fan to intake and top one to exhaust instead because heat rise. There were a few things that could have been done better tbh.

[@henrypeters6210]

force of convection is completely negligible compared the force exerted by a powered fan@@leonidastankiangaming

[@andrewmoon26]

Had the same question

[@markpew8111]

Yo this content is next lvl bro. You are doing novel things like designing your own super light mice, creating super charged mini-ITX builds and kitting out the inside of this PC with custom airflow kits inspired by the air intakes on high performance cars. All of this with top notch cinematography. You have become my FAVORITE tech KZbinr. Love your work.

[@clookoo2]

that's so funny, I did this once way back in high-school with cardboard and clear tape lol. Yours turned out waaay nicer obvs, cheers dude